Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM (w/ Adaptive High Beam System) › from 2021.07
RM3700E _59 Vehicle Exterior _093283 LIGHTING (EXT) _0486937 LIGHTING SYSTEM(w/ Adaptive High Beam System) J

LIGHTING (EXT)  LIGHTING SYSTEM(w/ Adaptive High Beam System)  Taillight Relay Circuit  


DESCRIPTION

The main body ECU (multiplex network body ECU) controls the operation of the TAIL relay.

WIRING DIAGRAM

E456316E02
4.042,3.927 6.448,4.385 2.406,0.458 10 false Power Distribution Box Assembly 5.365,0.854 5.677,1.052 0.313,0.198 10 false IC 4.865,3.313 6.208,3.604 1.344,0.292 10 false CXPI Transceiver 3.583,2.823 3.896,3.021 0.313,0.198 10 false 4E 3.594,2.604 3.906,2.802 0.313,0.198 10 false 30 5.979,4.833 7.146,5.563 1.167,0.729 10 false Main Body ECU (Multiplex Network Body ECU) 0.969,5.313 2.677,5.521 1.708,0.208 10 false : CXPI Communication Line 5.135,2.531 5.448,2.729 0.313,0.198 10 false +B 3.021,4.906 3.573,5.271 0.552,0.365 10 false A 4.542,2.802 4.854,3 0.313,0.198 10 false IPD

E437073E04
5.156,0.156 5.323,0.354 0.167,0.198 10 false A 1.927,0.781 2.094,0.979 0.167,0.198 10 false 1 4.292,0.781 4.458,0.979 0.167,0.198 10 false 2 3.99,0.896 4.229,1.083 0.24,0.188 10 false +S 2.146,0.927 2.385,1.115 0.24,0.188 10 false E 1.844,1.375 2.24,1.563 0.396,0.188 10 false O105 1.844,1.573 4.521,1.823 2.677,0.25 10 false Rear Combination Light Assembly LH 1.938,2.24 2.104,2.438 0.167,0.198 10 false 1 4.333,2.25 4.5,2.448 0.167,0.198 10 false 2 2.125,2.385 2.365,2.573 0.24,0.188 10 false E 3.885,2.375 4.271,2.563 0.385,0.188 10 false SHDI 1.875,2.844 2.271,3.031 0.396,0.188 10 false O108 1.865,3.01 4.542,3.26 2.677,0.25 10 false Rear Combination Light Assembly RH 3.635,3.677 3.802,3.875 0.167,0.198 10 false 1 1.677,3.677 1.844,3.875 0.167,0.198 10 false 2 3.427,3.771 3.667,3.958 0.24,0.188 10 false B 1.865,3.813 2.104,4 0.24,0.188 10 false E 1.688,4.25 1.938,4.448 0.25,0.198 10 false Y3 1.698,4.417 3.813,4.646 2.115,0.229 10 false License Plate Light Assembly LH 3.667,5.021 3.833,5.219 0.167,0.198 10 false 1 1.667,5.01 1.833,5.208 0.167,0.198 10 false 2 1.865,5.167 2.104,5.354 0.24,0.188 10 false E 3.448,5.146 3.688,5.333 0.24,0.188 10 false B 1.688,5.615 1.938,5.813 0.25,0.198 10 false Y4 1.698,5.781 3.813,6.01 2.115,0.229 10 false License Plate Light Assembly RH 5.938,6.073 7.104,6.625 1.167,0.552 10 false Main Body ECU (Multiplex Network Body ECU) 3.656,6.417 3.823,6.615 0.167,0.198 10 false 2 1.656,6.427 1.823,6.625 0.167,0.198 10 false 1 1.875,6.552 2.115,6.74 0.24,0.188 10 false E 3.438,6.531 3.677,6.719 0.24,0.188 10 false B 1.938,7.021 2.24,7.219 0.302,0.198 10 false Y13 1.948,7.177 3.521,7.396 1.573,0.219 10 false Rear Light Assembly LH 3.656,7.875 3.823,8.073 0.167,0.198 10 false 2 1.677,7.865 1.844,8.063 0.167,0.198 10 false 1 1.865,8.01 2.104,8.198 0.24,0.188 10 false E 3.448,8.01 3.688,8.198 0.24,0.188 10 false B 1.948,8.448 2.25,8.646 0.302,0.198 10 false Y15 1.958,8.604 3.531,8.823 1.573,0.219 10 false Rear Light Assembly RH

CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.

·

First perform the communication function inspections in How to Proceed with Troubleshooting to confirm that there are no CXPI communication malfunctions before troubleshooting this symptom.

Click herePower Source / Network>NETWORKING>CXPI COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING



PROCEDURE

1.READ VALUE USING GTS
a.

Using the GTS, read the Data List.

Body Electrical > Power Distribution Box > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Tail Light Input Signal Tail light input OFF or ON OFF: Taillight is not input
ON: Tail light is input
-
Body Electrical > Power Distribution Box > Data List
Tester Display
Tail Light Input Signal
50003 475 1290
OK:

Display changes according to the taillight illumination condition.



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS

NG

2.READ VALUE USING GTS
a.

Turn the light control switch to the TAIL position.


b.

Using the GTS, read the Data List.

Body Electrical > Power Distribution Box > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Tail Light Fuse Shut Off Status Tail light fuse condition OFF or ON OFF: Taillight fuse not shut off
ON: Taillight fuse shut off
-
Body Electrical > Power Distribution Box > Data List
Tester Display
Tail Light Fuse Shut Off Status
50003 475 1293
OK:

The Data List value displays "OFF".



Result:
Proceed to
OK
NG



OK

3.READ VALUE USING GTS

NG

4.INSPECT REAR COMBINATION LIGHT LENS AND BODY LH
3.READ VALUE USING GTS
a.

Using the GTS, read the Data List.

Body Electrical > Power Distribution Box > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Tail Light Output Signal Tail light output OFF or ON OFF: Taillight is not output
ON: Tail light is output
-
Body Electrical > Power Distribution Box > Data List
Tester Display
Tail Light Output Signal
50003 475 1291
OK:

Display changes according to the taillight illumination condition.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

4.INSPECT REAR COMBINATION LIGHT LENS AND BODY LH
a.

Disconnect the O105 rear combination light lens and body LH connector.


b.

Turn the light control switch to the AUTO (OFF) position.

NOTICE:

If the low beam headlights or clearance lights illuminate when the ignition switch is turned ON, shine a light on the automatic light control sensor to turn the low beam headlights off before operating the headlight dimmer switch.



c.

Turn the light control switch to the TAIL position.


d.

Using the GTS, read the Data List.

Body Electrical > Power Distribution Box > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Tail Light Fuse Shut Off Status Tail light fuse condition OFF or ON OFF: Taillight fuse not shut off
ON: Taillight fuse shut off
-
Body Electrical > Power Distribution Box > Data List
Tester Display
Tail Light Fuse Shut Off Status
50003 475 1293
OK:

The Data List value displays "OFF".



Result:
Proceed to
OK
NG



OK

NG

5.INSPECT REAR COMBINATION LIGHT LENS AND BODY RH
5.INSPECT REAR COMBINATION LIGHT LENS AND BODY RH
a.

Disconnect the O108 rear combination light lens and body RH connector.


b.

Turn the light control switch to the AUTO (OFF) position.

NOTICE:

If the low beam headlights or clearance lights illuminate when the ignition switch is turned ON, shine a light on the automatic light control sensor to turn the low beam headlights off before operating the headlight dimmer switch.



c.

Turn the light control switch to the TAIL position.


d.

Using the GTS, read the Data List.

Body Electrical > Power Distribution Box > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Tail Light Fuse Shut Off Status Tail light fuse condition OFF or ON OFF: Taillight fuse not shut off
ON: Taillight fuse shut off
-
Body Electrical > Power Distribution Box > Data List
Tester Display
Tail Light Fuse Shut Off Status
50003 475 1293
OK:

The Data List value displays "OFF".



Result:
Proceed to
OK
NG



OK

NG

6.INSPECT REAR LIGHT ASSEMBLY LH
6.INSPECT REAR LIGHT ASSEMBLY LH
a.

Disconnect the Y13 rear light assembly LH connector.


b.

Turn the light control switch to the AUTO (OFF) position.

NOTICE:

If the low beam headlights or clearance lights illuminate when the ignition switch is turned ON, shine a light on the automatic light control sensor to turn the low beam headlights off before operating the headlight dimmer switch.



c.

Turn the light control switch to the TAIL position.


d.

Using the GTS, read the Data List.

Body Electrical > Power Distribution Box > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Tail Light Fuse Shut Off Status Tail light fuse condition OFF or ON OFF: Taillight fuse not shut off
ON: Taillight fuse shut off
-
Body Electrical > Power Distribution Box > Data List
Tester Display
Tail Light Fuse Shut Off Status
50003 475 1293
OK:

The Data List value displays "OFF".



Result:
Proceed to
OK
NG



OK

NG

7.INSPECT REAR LIGHT ASSEMBLY RH
7.INSPECT REAR LIGHT ASSEMBLY RH
a.

Disconnect the Y15 rear light assembly RH connector.


b.

Turn the light control switch to the AUTO (OFF) position.

NOTICE:

If the low beam headlights or clearance lights illuminate when the ignition switch is turned ON, shine a light on the automatic light control sensor to turn the low beam headlights off before operating the headlight dimmer switch.



c.

Turn the light control switch to the TAIL position.


d.

Using the GTS, read the Data List.

Body Electrical > Power Distribution Box > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Tail Light Fuse Shut Off Status Tail light fuse condition OFF or ON OFF: Taillight fuse not shut off
ON: Taillight fuse shut off
-
Body Electrical > Power Distribution Box > Data List
Tester Display
Tail Light Fuse Shut Off Status
50003 475 1293
OK:

The Data List value displays "OFF".



Result:
Proceed to
OK
NG



OK

NG

8.INSPECT LICENSE PLATE LIGHT ASSEMBLY LH
8.INSPECT LICENSE PLATE LIGHT ASSEMBLY LH
a.

Disconnect the Y3 license plate light assembly LH connector.


b.

Turn the light control switch to the AUTO (OFF) position.

NOTICE:

If the low beam headlights or clearance lights illuminate when the ignition switch is turned ON, shine a light on the automatic light control sensor to turn the low beam headlights off before operating the headlight dimmer switch.



c.

Turn the light control switch to the TAIL position.


d.

Using the GTS, read the Data List.

Body Electrical > Power Distribution Box > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Tail Light Fuse Shut Off Status Tail light fuse condition OFF or ON OFF: Taillight fuse not shut off
ON: Taillight fuse shut off
-
Body Electrical > Power Distribution Box > Data List
Tester Display
Tail Light Fuse Shut Off Status
50003 475 1293
OK:

The Data List value displays "OFF".



Result:
Proceed to
OK
NG



OK

REPLACE LICENSE PLATE LIGHT ASSEMBLY LH

NG

9.INSPECT LICENSE PLATE LIGHT ASSEMBLY RH
9.INSPECT LICENSE PLATE LIGHT ASSEMBLY RH
a.

Disconnect the Y4 license plate light assembly RH connector.


b.

Turn the light control switch to the AUTO (OFF) position.

NOTICE:

If the low beam headlights or clearance lights illuminate when the ignition switch is turned ON, shine a light on the automatic light control sensor to turn the low beam headlights off before operating the headlight dimmer switch.



c.

Turn the light control switch to the TAIL position.


d.

Using the GTS, read the Data List.

Body Electrical > Power Distribution Box > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Tail Light Fuse Shut Off Status Tail light fuse condition OFF or ON OFF: Taillight fuse not shut off
ON: Taillight fuse shut off
-
Body Electrical > Power Distribution Box > Data List
Tester Display
Tail Light Fuse Shut Off Status
50003 475 1293
OK:

The Data List value displays "OFF".



Result:
Proceed to
OK
NG



OK

REPLACE LICENSE PLATE LIGHT ASSEMBLY RH

NG

10.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - REAR COMBINATION LIGHT LENS AND BODY AND LICENSE PLATE LIGHT ASSEMBLY AND REAR LIGHT A)
10.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - REAR COMBINATION LIGHT LENS AND BODY AND LICENSE PLATE LIGHT ASSEMBLY AND REAR LIGHT A)
a.

Disconnect the O105 rear combination light lens and body LH connector.


b.

Disconnect the O108 rear combination light lens and body RH connector.


c.

Disconnect the Y3 license plate light assembly LH connector.


d.

Disconnect the Y4 license plate light assembly RH connector.


e.

Disconnect the Y13 rear light assembly LH connector.


f.

Disconnect the Y15 rear light assembly RH connector.


g.

Disconnect the cable from the negative (-) auxiliary battery terminal.


h.

Disconnect the 4E power distribution box assembly connector.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(O105,O108,Y3,Y4,Y13,Y15)Location & Routing

Click Connector(O105)Body>Floor Wire>Rear Combination Light Assembly LH

Click Connector(O108)Body>Floor Wire>Rear Combination Light Assembly RH

Click Connector(Y3)Body>No. 2 Back Door Wire>License Plate Light Assembly LH

Click Connector(Y4)Body>No. 2 Back Door Wire>License Plate Light Assembly RH

Click Connector(Y13)Body>No. 2 Back Door Wire>Rear Light Assembly LH

Click Connector(Y15)Body>No. 2 Back Door Wire>Rear Light Assembly RH

O105-2 (+S) - Body ground Always 10 kΩ or higher
O108-2 (SHDI) - Body ground Always 10 kΩ or higher
Y3-1 (B) - Body ground Always 10 kΩ or higher
Y4-1 (B) - Body ground Always 10 kΩ or higher
Y13-1 (B) - Body ground Always 10 kΩ or higher
Y15-1 (B) - Body ground Always 10 kΩ or higher
4E-30 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR