The BIN resistance is equipped for the purpose of correcting variances in brightness (luminous flux) when the light control LED ECU is energizing the LED with a constant current to illuminate it.
Also, it monitors the voltage applied to the BIN resistance in order to detect abnormalities in the energizing current and thereby detect malfunctions.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from | Priority |
|---|---|---|---|---|---|
| B24441C | Low Beam LH Circuit Voltage Out of Range | Detection condition:
Ignition switch is to ON, low beam headlights illuminated Malfunction status:
·
Headlight lens sub-assembly LH (BIN resistance) malfunction ·
Open/short in headlight lens sub-assembly LH (BIN resistance) circuit Malfunction duration:
10 seconds or more |
·
Headlight lens sub-assembly LH ·
Harness or connector ·
Light control LED ECU LH |
Main Body | A |
| B24451C | Low Beam RH Circuit Voltage Out of Range | Detection condition:
Ignition switch is to ON, low beam headlights illuminated Malfunction status:
·
Headlight lens sub-assembly RH (BIN resistance) malfunction ·
Open/short in headlight lens sub-assembly RH (BIN resistance) circuit Malfunction duration:
10 seconds or more |
·
Headlight lens sub-assembly RH ·
Harness or connector ·
Light control LED ECU RH |
Main Body | A |
First perform the communication function inspections in How to Proceed with Troubleshooting to confirm that there are no CXPI communication malfunctions before troubleshooting this symptom.
First perform the communication function inspections in How to Proceed with Troubleshooting to confirm that there are no CAN communication malfunctions before troubleshooting this symptom.
Enter the following menus: Body Electrical / Main Body / Trouble Codes.
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Pre-procedure 1
Turn the ignition switch to ON.
Wait 10 seconds or more.
Turn the GTS on.
Enter the following menus: Body Electrical / Main Body / Trouble Codes.
Procedure 1
Check for DTCs.
| Result | Proceed to |
|---|---|
| B24441C is not output | A |
| B24441C is output | B |
Post-procedure 1
None
A
B
Enter the following menus: Body Electrical / Main Body / Trouble Codes.
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Pre-procedure 1
Turn the ignition switch to ON.
Wait 10 seconds or more.
Turn the GTS on.
Enter the following menus: Body Electrical / Main Body / Trouble Codes.
Procedure 1
Check for DTCs.
| Result | Proceed to |
|---|---|
| B24451C is not output | A |
| B24451C is output | B |
Post-procedure 1
None
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
Interchange the Headlight lens sub-assembly RH with LH and connect the connectors to them.
Clear the DTCs.
Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (w/o Adaptive High Beam System)>DTC CHECK / CLEAR
| Proceed to |
|---|
| NEXT |
NEXT
Pre-procedure 1
Turn the ignition switch to ON.
Wait 10 seconds or more.
Turn the GTS on.
Enter the following menus: Body Electrical / Main Body / Trouble Codes.
Procedure 1
Check for DTCs.
| Result | Proceed to |
|---|---|
| B24451C is output | A |
| B24451C is not output | B |
Post-procedure 1
None
A
B
Pre-procedure 1
Remove the headlight unit assembly RH.
Remove the wire harness.
Procedure 1
| *a | Front view of wire harness connector
(Light Control LED ECU RH) |
| *b | Front view of wire harness connector
(Headlight Lens Sub-assembly RH) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Result |
|---|---|---|---|
| B-12 - C-5 | Always | Below 1 Ω | |
| B-13 - C-4 | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure 1
None
OK
NG
Interchange the Headlight lens sub-assembly LH with RH and connect the connectors to them.
Clear the DTCs.
Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (w/o Adaptive High Beam System)>DTC CHECK / CLEAR
| Proceed to |
|---|
| NEXT |
NEXT
Pre-procedure 1
Turn the ignition switch to ON.
Wait 10 seconds or more.
Turn the GTS on.
Enter the following menus: Body Electrical / Main Body / Trouble Codes.
Procedure 1
Check for DTCs.
| Result | Proceed to |
|---|---|
| B24441C is output | A |
| B24441C is not output | B |
Post-procedure 1
None
A
B
Pre-procedure 1
Remove the headlight unit assembly LH.
Remove the wire harness.
Procedure 1
| *a | Front view of wire harness connector
(Light Control LED ECU LH) |
| *b | Front view of wire harness connector
(Headlight Lens Sub-assembly LH) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Result |
|---|---|---|---|
| B-12 - C-5 | Always | Below 1 Ω | |
| B-13 - C-4 | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure 1
None
OK
NG