The main body ECU (multiplex network body ECU) controls the rear fog light.
for RHD
for LHD
Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.*1
First, confirm that there is no malfunction in the power integration system. Refer to the How to Proceed with Troubleshooting procedure.
First perform the communication function inspections in How to Proceed with Troubleshooting to confirm that there are no CAN communication malfunctions before troubleshooting this symptom.
First perform the communication function inspections in How to Proceed with Troubleshooting to confirm that there are no CXPI communication malfunctions before troubleshooting this symptom.
*1: w/ Entry and Start System
Turn the light control switch to the TAIL position.
Turn the rear fog light switch on.
Using the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Rear Fog Light Fuse Shut Off Status | Rear fog light fuse condition | OFF or ON | OFF: Rear fog light fuse not shut off
ON: Rear fog light fuse shut off |
- |
| Tester Display |
|---|
| Rear Fog Light Fuse Shut Off Status |
The Data List value displays "OFF".
| Result | Proceed to |
|---|---|
| OK | A |
| NG (w/ Rear Turn Signal Light LED Type) | B |
| NG (w/ Rear Turn Signal Light Bulb Type) | C |
A
B
C
Using the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Rear Fog Light Output Signal | Rear fog light output | OFF or ON | OFF: Rear fog light is not output
ON: Rear fog light is output |
- |
| Tester Display |
|---|
| Rear Fog Light Output Signal |
Display changes according to the rear fog light switch operation.
| Proceed to |
|---|
| OK |
| NG |
OK
for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
NG
for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
Disconnect the Y14 rear fog light LED connector.
Turn the rear fog light switch off.
Turn the rear fog light switch on.
Using the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Rear Fog Light Fuse Shut Off Status | Rear fog light fuse condition | OFF or ON | OFF: Rear fog light fuse not shut off
ON: Rear fog light fuse shut off |
- |
The Data List value displays "OFF".
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the Y14*1 or Y12*2 rear fog light LED connector.
*1: for RHD
*2: for LHD
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the 4E power distribution box assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(Y14,Y12)Location & Routingewd_type=routing;type=c,c;code=Y14,Y12 Click Connector(Y14)Body>No. 2 Back Door Wire>Rear Light Assembly RHewd_type=component;type=c;code=Y14;pinno=3 Click Connector(Y12)Body>No. 2 Back Door Wire>Rear Light Assembly LHewd_type=component;type=c;code=Y12;pinno=3 |
||
| Y14-3 (B) or 4E-7 - Body ground*1 | Always | 10 kΩ or higher |
| Y12-3 (B) or 4E-7 - Body ground*2 | Always | 10 kΩ or higher |
*1: for RHD
*2: for LHD
| Proceed to |
|---|
| OK |
| NG |
OK
for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
NG
Disconnect the Y17*1 or Y36*2 rear fog light LED connector.
*1: for RHD
*2: for LHD
Turn the rear fog light switch off.
Turn the rear fog light switch on.
Using the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Rear Fog Light Fuse Shut Off Status | Rear fog light fuse condition | OFF or ON | OFF: Rear fog light fuse not shut off
ON: Rear fog light fuse shut off |
- |
The Data List value displays "OFF".
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the Y17*1 or Y36*2 rear fog light LED connector.
*1: for RHD
*2: for LHD
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the 4E power distribution box assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(Y17,Y36)Location & Routingewd_type=routing;type=c,c;code=Y17,Y36 Click Connector(Y17)Body>No. 2 Back Door Wire>Rear Light Assembly RHewd_type=component;type=c;code=Y17;pinno=1 Click Connector(Y36)Body>No. 2 Back Door Wire>Rear Fog Lightewd_type=component;type=c;code=Y36;pinno=1 |
||
| Y17-1 (B) or 4E-7 - Body ground*1 | Always | 10 kΩ or higher |
| Y36-1 (B) or 4E-7 - Body ground*2 | Always | 10 kΩ or higher |
*1: for RHD
*2: for LHD
| Proceed to |
|---|
| OK |
| NG |
OK
for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
NG