The main body ECU (multiplex network body ECU) controls the taillight and license plate light.
First perform the communication function inspections in How to Proceed with Troubleshooting to confirm that there are no CAN communication malfunctions before troubleshooting this symptom.
First perform the communication function inspections in How to Proceed with Troubleshooting to confirm that there are no CXPI communication malfunctions before troubleshooting this symptom.
Using the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Tail Light Input Signal | Tail light input | OFF or ON | OFF: Taillight is not input
ON: Tail light is input |
- |
| Tester Display |
|---|
| Tail Light Input Signal |
Display changes according to the taillight illumination condition.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
Turn the light control switch to the TAIL position.
Using the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Tail Light Fuse Shut Off Status | Tail light fuse condition | OFF or ON | OFF: Taillight fuse not shut off
ON: Taillight fuse shut off |
- |
| Tester Display |
|---|
| Tail Light Fuse Shut Off Status |
The Data List value displays "OFF".
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for Sequential Type Turn Signal Light) | B |
| NG (except Sequential Type Turn Signal Light) | C |
A
B
C
Using the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Tail Light Output Signal | Tail light output | OFF or ON | OFF: Taillight is not output
ON: Tail light is output |
- |
| Tester Display |
|---|
| Tail Light Output Signal |
Display changes according to the taillight illumination condition.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
Disconnect the O105 rear combination light lens and body LH connector.
Turn the light control switch to the AUTO (OFF) position.
If the low beam headlights or clearance lights illuminate when the ignition switch is turned ON, shine a light on the automatic light control sensor to turn the low beam headlights off before operating the headlight dimmer switch.
Turn the light control switch to the TAIL position.
Using the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Tail Light Fuse Shut Off Status | Tail light fuse condition | OFF or ON | OFF: Taillight fuse not shut off
ON: Taillight fuse shut off |
- |
| Tester Display |
|---|
| Tail Light Fuse Shut Off Status |
The Data List value displays "OFF".
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereVehicle Exterior>LIGHTING (EXT)>REAR COMBINATION LIGHT ASSEMBLY (for LED Headlight)>REMOVAL
NG
Disconnect the O108 rear combination light lens and body RH connector.
Turn the light control switch to the AUTO (OFF) position.
If the low beam headlights or clearance lights illuminate when the ignition switch is turned ON, shine a light on the automatic light control sensor to turn the low beam headlights off before operating the headlight dimmer switch.
Turn the light control switch to the TAIL position.
Using the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Tail Light Fuse Shut Off Status | Tail light fuse condition | OFF or ON | OFF: Taillight fuse not shut off
ON: Taillight fuse shut off |
- |
| Tester Display |
|---|
| Tail Light Fuse Shut Off Status |
The Data List value displays "OFF".
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereVehicle Exterior>LIGHTING (EXT)>REAR COMBINATION LIGHT ASSEMBLY (for LED Headlight)>REMOVAL
NG
Disconnect the Y13 rear light assembly LH connector.
Turn the light control switch to the AUTO (OFF) position.
If the low beam headlights or clearance lights illuminate when the ignition switch is turned ON, shine a light on the automatic light control sensor to turn the low beam headlights off before operating the headlight dimmer switch.
Turn the light control switch to the TAIL position.
Using the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Tail Light Fuse Shut Off Status | Tail light fuse condition | OFF or ON | OFF: Taillight fuse not shut off
ON: Taillight fuse shut off |
- |
| Tester Display |
|---|
| Tail Light Fuse Shut Off Status |
The Data List value displays "OFF".
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the Y15 rear light assembly RH connector.
Turn the light control switch to the AUTO (OFF) position.
If the low beam headlights or clearance lights illuminate when the ignition switch is turned ON, shine a light on the automatic light control sensor to turn the low beam headlights off before operating the headlight dimmer switch.
Turn the light control switch to the TAIL position.
Using the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Tail Light Fuse Shut Off Status | Tail light fuse condition | OFF or ON | OFF: Taillight fuse not shut off
ON: Taillight fuse shut off |
- |
| Tester Display |
|---|
| Tail Light Fuse Shut Off Status |
The Data List value displays "OFF".
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the Y3 license plate light assembly LH connector.
Turn the light control switch to the AUTO (OFF) position.
If the low beam headlights or clearance lights illuminate when the ignition switch is turned ON, shine a light on the automatic light control sensor to turn the low beam headlights off before operating the headlight dimmer switch.
Turn the light control switch to the TAIL position.
Using the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Tail Light Fuse Shut Off Status | Tail light fuse condition | OFF or ON | OFF: Taillight fuse not shut off
ON: Taillight fuse shut off |
- |
| Tester Display |
|---|
| Tail Light Fuse Shut Off Status |
The Data List value displays "OFF".
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the Y4 license plate light assembly RH connector.
Turn the light control switch to the AUTO (OFF) position.
If the low beam headlights or clearance lights illuminate when the ignition switch is turned ON, shine a light on the automatic light control sensor to turn the low beam headlights off before operating the headlight dimmer switch.
Turn the light control switch to the TAIL position.
Using the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Tail Light Fuse Shut Off Status | Tail light fuse condition | OFF or ON | OFF: Taillight fuse not shut off
ON: Taillight fuse shut off |
- |
| Tester Display |
|---|
| Tail Light Fuse Shut Off Status |
The Data List value displays "OFF".
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the O105 rear combination light lens and body LH connector.
Disconnect the O108 rear combination light lens and body RH connector.
Disconnect the Y3 license plate light assembly LH connector.
Disconnect the Y4 license plate light assembly RH connector.
Disconnect the Y13 rear light assembly LH connector.
Disconnect the Y15 rear light assembly RH connector.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the 4E power distribution box assembly connector.
Measure the resistance according to the value(s) in the table below.
| Proceed to |
|---|
| OK |
| NG |
OK
for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
NG
Disconnect the O102 rear combination light lens and body LH connector.
Turn the light control switch to the AUTO (OFF) position.
If the low beam headlights or clearance lights illuminate when the ignition switch is turned ON, shine a light on the automatic light control sensor to turn the low beam headlights off before operating the headlight dimmer switch.
Turn the light control switch to the TAIL position.
Using the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Tail Light Fuse Shut Off Status | Tail light fuse condition | OFF or ON | OFF: Taillight fuse not shut off
ON: Taillight fuse shut off |
- |
| Tester Display |
|---|
| Tail Light Fuse Shut Off Status |
The Data List value displays "OFF".
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereVehicle Exterior>LIGHTING (EXT)>REAR COMBINATION LIGHT ASSEMBLY (for Halogen Headlight)>REMOVAL
NG
Disconnect the O104 rear combination light lens and body RH connector.
Turn the light control switch to the AUTO (OFF) position.
If the low beam headlights or clearance lights illuminate when the ignition switch is turned ON, shine a light on the automatic light control sensor to turn the low beam headlights off before operating the headlight dimmer switch.
Turn the light control switch to the TAIL position.
Using the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Tail Light Fuse Shut Off Status | Tail light fuse condition | OFF or ON | OFF: Taillight fuse not shut off
ON: Taillight fuse shut off |
- |
| Tester Display |
|---|
| Tail Light Fuse Shut Off Status |
The Data List value displays "OFF".
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereVehicle Exterior>LIGHTING (EXT)>REAR COMBINATION LIGHT ASSEMBLY (for Halogen Headlight)>REMOVAL
NG
Disconnect the Y3 license plate light assembly LH connector.
Turn the light control switch to the AUTO (OFF) position.
If the low beam headlights or clearance lights illuminate when the ignition switch is turned ON, shine a light on the automatic light control sensor to turn the low beam headlights off before operating the headlight dimmer switch.
Turn the light control switch to the TAIL position.
Using the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Tail Light Fuse Shut Off Status | Tail light fuse condition | OFF or ON | OFF: Taillight fuse not shut off
ON: Taillight fuse shut off |
- |
| Tester Display |
|---|
| Tail Light Fuse Shut Off Status |
The Data List value displays "OFF".
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the Y4 license plate light assembly RH connector.
Turn the light control switch to the AUTO (OFF) position.
If the low beam headlights or clearance lights illuminate when the ignition switch is turned ON, shine a light on the automatic light control sensor to turn the low beam headlights off before operating the headlight dimmer switch.
Turn the light control switch to the TAIL position.
Using the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Tail Light Fuse Shut Off Status | Tail light fuse condition | OFF or ON | OFF: Taillight fuse not shut off
ON: Taillight fuse shut off |
- |
| Tester Display |
|---|
| Tail Light Fuse Shut Off Status |
The Data List value displays "OFF".
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the O102 rear combination light lens and body LH connector.
Disconnect the O104 rear combination light lens and body RH connector.
Disconnect the Y3 license plate light assembly LH connector.
Disconnect the Y4 license plate light assembly RH connector.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the 4D power distribution box assembly connector.
Disconnect the 4E power distribution box assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(O102,O104,Y3,Y4)Location & Routingewd_type=routing;type=c,c,c,c;code=O102,O104,Y3,Y4 Click Connector(O102)Body>Floor Wire>Rear Combination Light Assembly LHewd_type=component;type=c;code=O102;pinno=1 Click Connector(O104)Body>Floor Wire>Rear Combination Light Assembly RHewd_type=component;type=c;code=O104;pinno=1 Click Connector(Y3)Body>No. 2 Back Door Wire>License Plate Light Assembly LHewd_type=component;type=c;code=Y3;pinno=1 Click Connector(Y4)Body>No. 2 Back Door Wire>License Plate Light Assembly RHewd_type=component;type=c;code=Y4;pinno=1 |
||
| O102-1 (B) - Body ground | Always | 10 kΩ or higher |
| O104-1 (B) - Body ground | Always | 10 kΩ or higher |
| Y3-1 (B) - Body ground | Always | 10 kΩ or higher |
| Y4-1 (B) - Body ground | Always | 10 kΩ or higher |
| 4E-30 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
NG