Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › REAR INVERTER › from 2021.07
RM3700E _51 Engine / Hybrid System _093506 HYBRID / BATTERY CONTROL _0446831 REAR INVERTER A

HYBRID / BATTERY CONTROL  REAR INVERTER  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
A490436N01
6.479,0.229 6.813,0.229 false 6.094,2.031 6.427,2.031 false 3.99,0.844 4.323,0.844 false 5.719,3.542 6.052,3.542 false 0.417,3.323 0.51,3.573 0.51,3.573 0.677,3.573 false 6.26,0.115 6.938,0.458 0.677,0.344 18 false 1 3.74,0.698 4.063,1.01 0.323,0.313 18 false 3 6.51,1.906 6.833,2.219 0.323,0.313 18 false 4 6.344,3.396 6.667,3.708 0.323,0.313 18 false 5 0.74,3.438 1.063,3.75 0.323,0.313 18 false 2 5.375,2.844 5.625,3.01 0.25,0.167 10 false x6

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
2 SERVICE PLUG GRIP G3834 - - -
3 REAR NO. 1 FLOOR BOARD 58415Q - - -
4 REAR DECK FLOOR BOX 64993 - - -
5 HYBRID INVERTER PROTECTOR ASSEMBLY G92D0 (Click here) - -

A462813N01
2.948,1.406 2.948,1.646 false 5.24,0.906 4.917,0.906 false 6.458,0.292 6.792,0.292 false 5.229,2.063 5.375,2.323 5.375,2.323 5.531,2.323 false 5.229,4.208 5.229,4.458 false 1.594,1.677 1.594,1.917 false 5.292,3.802 5.521,3.177 5.521,3.177 5.677,3.177 false 2.698,3.573 2.479,3.885 2.479,3.885 2.313,3.885 false 3,5.052 3,5.323 false 1.531,1.917 1.813,2.271 0.281,0.354 18 false 8 2.833,1.635 3.115,1.99 0.281,0.354 18 false 9 4.781,1.844 5.063,2.198 0.281,0.354 18 false 7 6.271,0.156 6.552,0.51 0.281,0.354 18 false 7 5.896,2.219 6.396,2.583 0.5,0.365 18 false 10 5.115,4.521 5.708,4.927 0.594,0.406 18 false 14 1.885,0.927 2.167,1.104 0.281,0.177 10 false x4 3.146,0.635 3.344,0.802 0.198,0.167 10 false x4 4.75,0.24 4.948,0.406 0.198,0.167 10 false x5 5.146,1.5 5.344,1.667 0.198,0.167 10 false x5 3.729,3.823 3.927,3.99 0.198,0.167 10 false x3 5.625,0.781 6.26,1.094 0.635,0.313 18 false 6, 11 6.042,3.052 6.594,3.427 0.552,0.375 18 false 14 1.979,3.76 2.49,4.188 0.51,0.427 18 false 12 2.865,5.354 3.385,5.771 0.521,0.417 18 false 13 6.438,3.5 6.635,3.667 0.198,0.167 10 false x3 3.906,5.198 4.104,5.365 0.198,0.167 10 false x4 5.365,3.854 5.563,4.021 0.198,0.167 10 false x3

Procedure Part Name Code
Z101186

Z101188

Z101187

6 REMOVE INVERTER TERMINAL COVER G9223 (Click here) - -
7 CHECK TERMINAL VOLTAGE - (Click here) - -
8 HV FLOOR UNDER WIRE 821H1 (Click here) - -
9 HV BATTERY PACK WIRE 821H3 (Click here) - -
10 REAR TRACTION MOTOR CABLE - (Click here) - -
11 TEMPORARILY INSTALL INVERTER TERMINAL COVER G9223 (Click here) - -
12 REAR HYBRID MOTOR CONTROL INVERTER ASSEMBLY G92B0 (Click here) - -
13 HV INVERTER COOLING COVER G92B2 (Click here) - -
14 HV INVERTER COOLING FAN G92B1 (Click here) - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear hybrid motor control inverter assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedures Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: When performing learning using the GTS.

Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (w/o Advanced Park) (Click here)
Initialize back door lock Power door lock control system (Click here)

CAUTION:
·
A340386

Orange wire harnesses and connectors indicate high-voltage circuits. To prevent electric shock, always follow the procedure described in the repair manual.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION

·
A340358

To prevent electric shock, wear insulated gloves when working on wire harnesses and components of the high voltage system.



HINT:

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Parking support brake system (Click here)
Pre-collision system
Parking support brake system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 1. PRECAUTION

Z101186

Click here(Click here)

Hide 58415Q 3.REMOVE REAR NO. 1 FLOOR BOARD

Hide 64993 4.REMOVE REAR DECK FLOOR BOX

Hide G92D0 5.REMOVE HYBRID INVERTER PROTECTOR ASSEMBLY

Z101186

NOTICE:

When removing the hybrid inverter protector assembly, be careful not to damage the parts around it.



a.
A458333


Hide G9223 6.REMOVE INVERTER TERMINAL COVER

Z101186

CAUTION:

Be sure to wear insulated gloves.


NOTICE:
·

Make sure to pull the inverter terminal cover straight out, as a connector is connected to the inside of the inverter terminal cover.

·

Do not touch the waterproof seal of the inverter terminal cover.

·

Do not allow any foreign matter or water to enter the rear hybrid motor control inverter assembly.

·

Make sure that the interlock is installed to the inverter terminal cover.




a.
A458334C01
3.396,2.021 3.615,2.333 3.615,2.333 3.948,2 true 3.594,2.323 3.01,2.083 true 3.333,1.583 3.167,1.583 3.167,1.583 2.958,1.781 true 3.583,2.354 3.896,2.552 0.313,0.198 10 false *b 3.385,1.51 3.698,1.708 0.313,0.198 10 false *a
*a Interlock *b Waterproof Seal



Hide 7.CHECK TERMINAL VOLTAGE

Z101186

CAUTION:

Be sure to wear insulated gloves.


NOTICE:
·

Do not allow any foreign matter or water to enter the rear hybrid motor control inverter assembly.

·

Do not use A terminal for measurement.




a.
A458335N01
3.25,1.75 3.417,1.75 3.417,1.75 3.719,1.885 true 3.104,1.688 3.26,1.885 0.156,0.198 10 false A 0.521,0.073 0.729,0.385 0.208,0.313 18 false i

i.

Using a voltmeter, measure the voltage between the terminals of the 2 phase connectors.

Standard Voltage:

0 V


HINT:

Use a measuring range of DC 750 V or more on the voltmeter.




Hide 821H1 8.DISCONNECT FLOOR UNDER WIRE

Z101186

CAUTION:

Be sure to wear insulated gloves.


NOTICE:
·

Do not allow any foreign matter or water to enter the rear hybrid motor control inverter assembly.

·

Do not touch the waterproof seal or terminals of the HV floor under wire.

·

Do not damage the terminals, connector housing or rear hybrid motor control inverter assembly during disconnection.

·

Insulate the disconnected terminals with insulating tape.




a.
A458336C01
3.125,2 3.458,2 true 2.927,1.927 3.24,2.125 0.313,0.198 10 false *a 0.479,0.073 0.76,0.396 0.281,0.323 18 false i
*a Waterproof Seal - -


i.

Using an insulated tool, remove the 4 bolts and disconnect the HV floor under wire from the rear hybrid motor control inverter assembly.



Hide 821H3 9.DISCONNECT HV BATTERY PACK WIRE

Z101186

CAUTION:

Be sure to wear insulated gloves.


NOTICE:
·

Do not allow any foreign matter or water to enter the rear hybrid motor control inverter assembly.

·

Do not touch the waterproof seal or terminals of the HV battery pack wire.

·

Do not damage the terminals, connector housing or rear hybrid motor control inverter assembly during disconnection.

·

Insulate the disconnected terminals with insulating tape.

·

Make sure to pull the HV battery pack wire straight out, as a connector is connected to the inside of the inverter terminal cover.




a.
A458337C01
3.021,2.094 3.354,2.094 true 3.771,2.385 4.104,2.385 false 2.833,2.031 3.146,2.229 0.313,0.198 10 false *b 4.167,2.313 4.479,2.51 0.313,0.198 10 false *a 0.49,0.073 0.667,0.385 0.177,0.313 18 false i
*a Interlock *b Waterproof Seal


i.

Using an insulated tool, remove the 4 bolts and disconnect the HV battery pack wire from the rear hybrid motor control inverter assembly.



Hide 10.DISCONNECT REAR TRACTION MOTOR CABLE

Z101186

CAUTION:

Be sure to wear insulated gloves.


NOTICE:
·

Do not allow any foreign matter or water to enter the rear hybrid motor control inverter assembly.

·

Do not touch the waterproof seal or terminals of the rear traction motor cable.

·

Do not damage the terminals, connector housing or rear hybrid motor control inverter assembly during disconnection.

·

Insulate the disconnected terminals with insulating tape.

·

Make sure to pull the rear traction motor cable out, as a connector is connected to the inside of the inverter terminal cover.




a.
A458338C01
3.948,1.583 3.573,2 true 4.01,1.5 4.323,1.698 0.313,0.198 10 false *a 0.51,0.083 0.698,0.385 0.188,0.302 18 false i
*a Waterproof Seal - -


i.

Using an insulated tool, remove the 5 bolts and disconnect the rear traction motor cable from the rear hybrid motor control inverter assembly.



Hide G9223 11.TEMPORARILY INSTALL INVERTER TERMINAL COVER

Z101186

CAUTION:

Be sure to wear insulated gloves.


NOTICE:

Do not touch the waterproof seal of the inverter terminal cover.



a.

Temporarily install the inverter terminal cover with the 5 bolts.

A458339N04
2,0.01 2.281,0.365 0.281,0.354 18 false i

i.

Temporarily install the inverter terminal cover with the 5 bolts.



Hide G92B0 12.REMOVE REAR HYBRID MOTOR CONTROL INVERTER ASSEMBLY

Z101186

CAUTION:

Be sure to wear insulated gloves.



a.
A460049N02
0.438,0.083 0.625,0.365 0.188,0.281 18 false i 3.875,0.094 4.063,0.375 0.188,0.281 18 true ii

i.

Disconnect the 2 rear hybrid motor control inverter assembly connectors.

NOTICE:
·

Do not touch the waterproof seal or terminals of the connector.

·

Do not damage the terminals, connector housing or rear hybrid motor control inverter assembly during disconnection.

·

Cover the hole where the cable was connected with tape (non-residue type) or equivalent to prevent entry of foreign matter.

·

Do not allow any foreign matter or water to enter the rear hybrid motor control inverter assembly.

·

Insulate the disconnected terminals with insulating tape.

·

To prevent damage due to staticelectricity, do not touch the terminals of the disconnected connectors.




ii.

Remove the 3 bolts and rear hybrid motor control inverter assembly.

NOTICE:
·

Do not damage the terminals, connector housing or rear hybrid motor control inverter assembly during disconnection.

·

Cover the hole where the cable was connected with tape (non-residue type) or equivalent to prevent entry of foreign matter.

·

Do not allow any foreign matter or water to enter the rear hybrid motor control inverter assembly.

·

Insulate the disconnected terminals with insulating tape.

·

To prevent damage due to staticelectricity, do not touch the terminals of the disconnected connectors.





Hide G92B2 13.REMOVE HV INVERTER COOLING COVER

Z101186

CAUTION:

Be sure to wear insulated gloves.


HINT:

Perform this procedure only when replacement of the HV inverter cooling fan is necessary.



a.
A458342N01
0.458,0.094 0.615,0.385 0.156,0.292 18 false i

i.

Using a T25 "TORX" socket wrench, remove the 4 bolts and HV inverter cooling cover from the rear hybrid motor control inverter assembly.



Hide G92B1 14.REMOVE HV INVERTER COOLING FAN

Z101186

CAUTION:

Be sure to wear insulated gloves.


HINT:

Perform this procedure only when replacement of the HV inverter cooling fan is necessary.



a.
A460050N01
2.469,0.719 2.667,1.063 0.198,0.344 18 true ii 1.51,0.771 1.698,1.063 0.188,0.292 18 true i 4.969,0.406 5.167,0.75 0.198,0.344 18 true iii 4.073,1.177 4.313,1.5 0.24,0.323 18 true iv

i.

Disconnect the rear hybrid motor control inverter assembly.


ii.

Disengage the clamp.


iii.

Disengage the 2 guides.


iv.

Using a T20 "TORX" socket wrench, remove the 3 bolts and HV inverter cooling fan from the rear hybrid motor control inverter assembly.