Home › Suspension › REAR SUSPENSION › REAR SHOCK ABSORBER › from 2021.07
RM3700E _53 Suspension _093739 REAR SUSPENSION _0441856 REAR SHOCK ABSORBER A

REAR SUSPENSION  REAR SHOCK ABSORBER  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
C444457N02
4.25,4.583 4.75,5.25 0.5,0.667 1.458,0.583 1.708,0.583 false 1.979,1.833 2.313,1.833 false 4.104,1.385 4.469,1.385 false 4.021,2.667 4.781,2.667 false 4.844,3.625 5.333,3.625 false 1.406,1.625 1.729,1.625 false 1.281,0.406 1.563,0.76 0.281,0.354 18 false 2 1.177,1.438 1.458,1.792 0.281,0.354 18 false 3 2.385,1.646 2.667,2 0.281,0.354 18 false 4 4.552,1.208 4.833,1.563 0.281,0.354 18 false 6 5.198,2.5 5.76,2.813 0.563,0.313 18 false 5 4.656,3.479 4.938,3.833 0.281,0.354 18 false 1 4.281,4.604 4.656,4.844 0.375,0.24 12 false *A

Procedure Part Name Code
Z101186

Z101188

Z101187

1 REAR WHEEL - - - -
2 DECK SIDE TRIM COVER 64715C - - -
3 REAR SHOCK ABSORBER CUSHION RETAINER 48597A (Click here) - -
4 REAR SUSPENSION SUPPORT 48755 - - -
5 REAR SHOCK ABSORBER ASSEMBLY 48540 (Click here) - -
6 REAR SUSPENSION SUPPORT ASSEMBLY 48760B - - -

*A for 2WD - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the rear shock absorber assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedure Effect/Inoperative when not Performed Link
for 2WD:
Rear wheel alignment adjustment
for HV Model TMC Made:
1.

Perform "Reset Memory"

2.

Perform calibration (linear solenoid valve offset learning, SM solenoid valve offset learning, brake pedal stroke sensor assembly zero point calibration, system information memorization, and yaw rate and acceleration sensor zero point calibration)


·

DTCs are stored

·

ABS warning light illuminates

·

Brake system warning light (yellow indicator)

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)
for HV Model TMMF Made:
1.

Perform "Reset Memory"

2.

Perform calibration (brake pedal stroke sensor assembly zero point calibration, system information memorization, and yaw rate and acceleration sensor zero point calibration)


·

DTCs are stored

·

ABS warning light illuminates

·

Brake system warning light (yellow indicator)

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)
for Gasoline Model:
Calibration
·

DTCs are stored

·

ABS warning light illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


for TMC Made:
(Click here)
for TMMF Made:
(Click here)
for AWD:
Rear wheel alignment adjustment
for TMC Made:
1.

Perform "Reset Memory"

2.

Perform calibration (linear solenoid valve offset learning, SM solenoid valve offset learning, brake pedal stroke sensor assembly zero point calibration, system information memorization, and yaw rate and acceleration sensor zero point calibration)


·

DTCs are stored

·

ABS warning light illuminates

·

Brake system warning light (yellow indicator)

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)
for TMMF Made:
Calibration
·

DTCs are stored

·

ABS warning light illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement.)
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking support brake system (Click here)
w/ Advanced Park:
Advanced Park
(Click here)
Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)
·

Parking assist ECU initialization

·

Adjust steering angle


Panoramic view monitor system w/o Advanced Park:
(Click here)
w/ Advanced Park:
(Click here)
w/ Advanced Park:
Advanced Park
(Click here)

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1.REMOVE REAR WHEEL

Hide 64715C 2.REMOVE DECK SIDE TRIM COVER

a.
C444383


Hide 48597A 3.REMOVE REAR SHOCK ABSORBER CUSHION RETAINER

a.
C484090C02
0.813,0.104 1.094,0.417 0.281,0.313 18 true i 4.292,0.104 4.573,0.417 0.281,0.313 18 true ii 0.76,2.031 1.469,2.333 0.708,0.302 18 true iii 0.198,0.135 0.573,0.365 0.375,0.229 12 false *A 3.729,0.146 4.104,0.375 0.375,0.229 12 false *B 4.302,1.99 4.583,2.302 0.281,0.313 18 true iv 1.323,3.479 1.635,3.677 0.313,0.198 10 true *a 3.104,3.354 3.417,3.552 0.313,0.198 10 true *b
*A for 2WD *B for AWD
*a Turn *b Hold


i.

for 2WD:

Support the spring seat of the rear axle beam assembly using a jack and wooden block.

CAUTION:

Do not jack up the rear axle beam assembly too high as the vehicle may fall.


NOTICE:
·

When jacking up the rear axle beam assembly, be sure to jack it up slowly.

·

Make sure to perform this operation with the vehicle kept as low as possible.

·

Keep supporting the rear axle beam assembly with a jack until the installation of the rear shock absorber assembly is completed.




ii.

for AWD:

Support the spring seat of the rear No. 1 suspension arm assembly using a jack and wooden block.

CAUTION:

Do not jack up the rear axle beam assembly too high as the vehicle may fall.


NOTICE:
·

When jacking up the rear No. 1 suspension arm assembly, be sure to jack it up slowly.

·

Make sure to perform this operation with the vehicle kept as low as possible.

·

Keep supporting the rear No. 1 suspension arm assembly with a jack until the installation of the rear shock absorber assembly is completed.




iii.

Using a 5 mm hexagon socket wrench, secure the rear shock absorber assembly rod and remove the nut using a wrench.


iv.

Remove the rear shock absorber cushion retainer.



Hide 48755 4.REMOVE REAR SUSPENSION SUPPORT

a.
C444384


Hide 48540 5.REMOVE REAR SHOCK ABSORBER ASSEMBLY

a.

for 2WD:

C443642N01
0.406,0.063 0.688,0.417 0.281,0.354 18 false i

i.

Remove the bolt while keeping the nut from rotating and remove the rear shock absorber assembly.

NOTICE:

Because the nut has its own stopper, do not turn the nut. Loosen the bolt with the nut secured.




b.

for AWD:

C443643

i.

Remove the bolt and remove the rear shock absorber assembly.



Hide 48760B 6.REMOVE REAR SUSPENSION SUPPORT ASSEMBLY

a.
C429706