Home › Drivetrain › DRIVE SHAFT / PROPELLER SHAFT › REAR DRIVE SHAFT ASSEMBLY › from 2021.07
RM3700E _52 Drivetrain _094372 DRIVE SHAFT / PROPELLER SHAFT _0444428 REAR DRIVE SHAFT ASSEMBLY A

DRIVE SHAFT / PROPELLER SHAFT  REAR DRIVE SHAFT ASSEMBLY  INSTALLATION  


CAUTION / NOTICE / HINT

COMPONENTS (INSTALLATION)
C445434N01
5.323,1.323 6.042,1.49 0.719,0.167 5.281,1.281 6.083,1.531 0.802,0.25 4.906,1.729 5.146,1.396 5.146,1.396 5.323,1.396 false 3.417,2.365 3.583,2.365 3.583,2.365 4.438,2.052 false 3.24,2.24 3.521,2.594 0.281,0.354 18 false 1 4.74,1.563 5.021,1.917 0.281,0.354 10 false x4 4.938,1.708 5.219,2.063 0.281,0.354 10 false x4 5.396,1.323 6.479,1.656 1.083,0.333 8 false 56 (571, 41)

Procedure Part Name Code
Z101186

Z101188

Z101187

1 REAR DRIVE SHAFT ASSEMBLY 42340B (Click here) - -

V111893

Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf)
V103638

Do not apply lubricants to the threaded parts

C445435N01
3.25,2.25 4.156,2.417 0.906,0.167 3.208,2.219 4.198,2.458 0.99,0.24 0.104,1.083 1.083,1.271 0.979,0.188 0.063,1.042 1.115,1.313 1.052,0.271 5.771,1.385 5.979,1.125 5.979,1.125 6.146,1.125 false 4.167,2.344 4.25,2.344 4.25,2.344 4.313,1.76 false 1.083,1.167 1.25,1.167 1.25,1.167 1.344,1.469 false 6.458,0.208 6.865,0.208 false 1.573,1.948 1.74,1.948 1.74,1.948 1.823,1.448 false 0.75,2 0.917,2 0.917,2 1,1.667 false 6.24,1.021 6.521,1.375 0.281,0.354 18 false 4 1.396,1.823 1.677,2.177 0.281,0.354 18 false 3 3,2.188 3.281,2.542 0.281,0.354 18 false 2 2.844,2.229 3.125,2.583 0.281,0.354 10 false ● 0.135,1.094 1.292,1.26 1.156,0.167 8 false 8.5 (87, 75 in.*lbf) 3.292,2.26 4.26,2.458 0.969,0.198 8 false 216 (2203, 159) 6.292,0.073 6.573,0.427 0.281,0.354 18 false 5 0.583,1.948 0.865,2.302 0.281,0.354 10 false *1

Procedure Part Name Code
Z101186

Z101188

Z101187

2 REAR AXLE SHAFT NUT 42312B (Click here) - -
3 REAR SKID CONTROL SENSOR 89544E (Click here)
4 REAR WHEEL - - - -
5 CHECK FOR SPEED SENSOR SIGNAL - (Click here) - -

*1 NO. 2 PARKING BRAKE WIRE ASSEMBLY - -
V111893

Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) ● Non-reusable part
V103638

Do not apply lubricants to the threaded parts - -

CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 42340B 1.INSTALL REAR DRIVE SHAFT ASSEMBLY

a.
C446098C01
2.75,0.656 2.385,1.427 2.385,1.427 2.875,0.958 true 5.5,1.167 5.667,1.167 5.667,1.167 5.667,1.5 true 5.5,1.25 5.667,1.25 true 0.396,0.083 0.677,0.438 0.281,0.354 18 false i 3.938,0.104 4.438,0.365 0.5,0.26 18 true ii, iii 2.281,1.49 2.594,1.688 0.313,0.198 10 false *a 5.563,1.5 5.802,1.667 0.24,0.167 10 true *a
*a Matchmark - -


i.

Align the matchmarks and install the rear drive shaft assembly to the rear axle hub and bearing assembly.

NOTICE:
·

Do not damage the rear drive shaft outboard joint boot.

·

Check that there is no foreign matter on the contact surfaces.




ii.

Align the matchmarks on the rear drive shaft assembly and differential side gear shaft sub-assembly.

NOTICE:

Do not damage the rear drive shaft inboard joint boot.



iii.

Install the 4 nuts and 4 washers.

Torque:
56 N*m (571 kgf*cm, 41 ft.*lbf)



Hide 42312B 2.INSTALL REAR AXLE SHAFT NUT

a.
C446099N02
3.865,0.073 4.375,0.365 0.51,0.292 18 true ii, iii 0.427,0.083 0.708,0.438 0.281,0.354 18 false i 2,2.083 2.292,2.323 0.292,0.24 18 true iv

i.

Clean the threaded parts on the rear drive shaft assembly and a new rear axle shaft nut using non-residue solvent.

NOTICE:
·

Be sure to perform this work even when using a new rear drive shaft assembly.

·

Keep the threaded parts free of oil and foreign matter.




ii.

Keep depressing the brake pedal to prevent the rear drive shaft assembly from rotating.


iii.

Using a 30 mm deep socket wrench, temporarily install the rear axle shaft nut.

Torque:
216 N*m (2203 kgf*cm, 159 ft.*lbf)


iv.

Using a chisel and hammer, stake the rear axle shaft nut.



Hide 89544E 3.INSTALL REAR SKID CONTROL SENSOR

Z101186

Click here(Click here)

Hide 4.INSTALL REAR WHEEL