Home › Engine / Hybrid System › 1NZ-FE ENGINE CONTROL › 1NZ-FE SFI SYSTEM › 2011.08–2016.09
RM19S0E _51 Engine / Hybrid System _051448 1NZ-FE ENGINE CONTROL _0248039 1NZ-FE SFI SYSTEM U

1NZ-FE ENGINE CONTROL  1NZ-FE SFI SYSTEM  TERMINALS OF ECM  


U158094E02
5.51,0.26 5.854,0.438 0.344,0.177 10 false A74 2.24,0.25 2.615,0.427 0.375,0.177 10 false B84

HINT:

The standard normal voltage between each pair of ECM terminals is shown in the table below. The appropriate conditions for checking each pair of terminals are also indicated. The result of checks should be compared with the standard normal voltage for that pair of terminals, displayed in the Specified Condition column. The illustration above can be used as a reference to identify the ECM terminal locations.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A74-20 (BATT) - B84-104 (E1) Y - W-B Battery (for measuring battery voltage and for ECM memory) Always 11 to 14 V
A74-2 (+B) - B84-104 (E1) B - W-B Power source of ECM Ignition switch ON 11 to 14 V
A74-1 (+B2) - B84-104 (E1) B - W-B Power source of ECM Ignition switch ON 11 to 14 V
A74-3 (+BM) - B84-43 (ME01) GR - BR Power source of throttle actuator Always 11 to 14 V
B84-85 (IGT1) - B84-104 (E1) W - W-B No. 1 ignition coil (ignition signal) Idling Pulse generation
(See waveform 1)
B84-84 (IGT2) - B84-104 (E1) V - W-B
B84-83 (IGT3) - B84-104 (E1) G - W-B
B84-82 (IGT4) - B84-104 (E1) LG - W-B
B84-81 (IGF1) - B84-104 (E1) Y - W-B No. 1 ignition coil (ignition confirmation signal) Ignition switch ON 4.5 to 5.5 V
Idling Pulse generation
(See waveform 1)
B84-122 (NE+) - B84-121 (NE-) L - P Crankshaft position sensor Idling with warm engine Pulse generation
(See waveform 2)
B84-99 (VV1+) - B84-121 (NE-) W - P Camshaft position sensor Idling with warm engine Pulse generation
(See waveform 2)
B84-108 (#10) - B84-45 (E01) B - BR Fuel injector assembly Ignition switch ON 11 to 14 V
B84-107 (#20) - B84-45 (E01) GR - BR
B84-106 (#30) - B84-45 (E01) P - BR Idling Pulse generation
(See waveform 3)
B84-105 (#40) - B84-45 (E01) L - BR
B84-109 (HT1A) - B84-86 (E03) G - W-B Heated oxygen sensor (sensor 1) heater Ignition switch ON 11 to 14 V
B84-112 (OX1A) - B84-90 (EX1A) B - V Heated oxygen sensor (sensor 1) Engine speed maintained at 2500 rpm for 2 minutes after warming up sensor Pulse generation
(See waveform 4)
B84-47 (HT1B) - B84-86 (E03) L - W-B Heated oxygen sensor (sensor 2) heater Ignition switch ON 11 to 14 V
B84-64 (OX1B) - B84-87 (EX1B) B - GR Heated oxygen sensor (sensor 2) Engine speed maintained at 2500 rpm for 2 minutes after warming up sensor Pulse generation
(See waveform 5)
B84-110 (KNK1) - B84-111 (EKNK) R - G Knock sensor Engine speed maintained at 4000 rpm after warming up engine Pulse generation
(See waveform 6)
A74-8 (SPD) - B84-104 (E1) V - W-B Speed signal from combination meter assembly Driving at 20 km/h (12 mph) Pulse generation
(See waveform 7)
B84-97 (THW) - B84-96 (ETHW) V - BR Engine coolant temperature sensor Idling, Engine coolant temperature 80°C (176°F) 0.2 to 1.0 V
B84-65 (THA) - B84-88 (ETHA) P - G Intake air temperature sensor Idling, Intake air temperature 20°C (68°F) 1.5 to 3.0 V
B84-118 (VG) - B84-116 (E2G) GR - L Mass air flow meter Idling, Shift lever position neutral, A/C switch OFF 0.5 to 3.0 V
A74-24 (W) - B84-104 (E1) B - W-B MIL Ignition switch to ON
(MIL goes on)
Below 1.5 V
Idling 11 to 14 V
A74-48 (STA) - B84-104 (E1) BR - W-B Starter signal Cranking 5.5 V or more
B84-52 (NSW) - A84-104 (E1) BE - W-B Clutch start switch signal*1
Park/neutral position switch signal*2
Ignition switch ON
(clutch pedal depressed)*1
Below 1.5 V
Ignition switch ON
(clutch pedal released)*1
11 to 14 V
Ignition switch ON
(shift lever in P, N)*2
Below 1.5 V
Ignition switch ON
(shift lever not in P, N)*2
11 to 14 V
Cranking 6 to 13 V
B84-115 (VTA1) - B84-91 (ETA) Y - V Throttle position sensor (for engine control) Ignition switch ON, Throttle valve fully closed 0.5 to 1.1 V
Ignition switch ON, Throttle valve fully open 3.2 to 4.8 V
B84-114 (VTA2) - B84-91 (ETA) GR - V Throttle position sensor (for sensor malfunction detection) Ignition switch ON, Throttle valve fully closed 2.1 to 3.1 V
Ignition switch ON, Throttle valve fully open 4.6 to 5.0 V
B84-67 (VCTA) - B84-91 (ETA) W - V Power source of sensor (specific voltage) Ignition switch ON 4.5 to 5.5 V
A74-57 (VCPA) - A74-59 (EPA) G - V Power source of accelerator pedal position sensor (for VPA) Ignition switch ON 4.5 to 5.5 V
A74-55 (VPA) - A74-59 (EPA) R - V Accelerator pedal position sensor (for engine control) Ignition switch ON, Accelerator pedal released 0.5 to 1.1 V
Ignition switch ON, Accelerator pedal fully depressed 2.6 to 4.5 V
A74-56 (VPA2) - A74-60 (EPA2) L - B Accelerator pedal position sensor (for sensor malfunctioning detection) Ignition switch ON, Accelerator pedal released 1.2 to 2.0 V
Ignition switch ON, Accelerator pedal fully depressed 3.4 to 4.7 V
A74-58 (VCP2) - A74-60 (EPA2) W - B Power source of accelerator pedal position sensor (for VPA2) Ignition switch ON 4.5 to 5.5 V
B84-42 (M+) - B84-43 (ME01) G - BR Throttle actuator Idling with warm engine Pulse generation
(See waveform 8)
B84-41 (M-) - B84-43 (ME01) BR - BR Throttle actuator Idling with warm engine Pulse generation
(See waveform 9)
A74-36 (STP) - B84-104 (E1) LG - W-B Stop light switch assembly Brake pedal depressed 11 to 14 V
Brake pedal released Below 1.5 V
A74-35 (ST1-) - B84-104 (E1) Y - W-B Stop light switch assembly (opposite to STP terminal) Ignition switch ON, Brake pedal depressed Below 1.5 V
Ignition switch ON, Brake pedal released 11 to 14 V
B84-49 (PRG) - B84-45 (E01) L - BR Purge VSV Ignition switch ON 11 to 14 V
Idling, under purge control Pulse generation
(See waveform 10)
A74-7 (FC) - B84-45 (E01) V - BR Fuel pump control Ignition switch ON 11 to 14 V
Idling Below 1.5 V
A74-15 (TACH) - B84-104 (E1) LG - W-B Engine speed Idling Pulse generation
(See waveform 11)
A74-27 (TC) - B84-104 (E1) L - W-B Terminal TC of DLC 3 Ignition switch ON 11 to 14 V
B84-100 (OC1+) - B84-123 (OC1-) BR - Y Camshaft timing oil control valve assembly (OCV) Idling Pulse generation
(See waveform 12)
A74-41 (CANH) - B84-104 (E1) L - W-B CAN communication line Ignition switch ON Pulse generation
(See waveform 13)
A74-49 (CANL) - B84-104 (E1) W - W-B CAN communication line Ignition switch ON Pulse generation
(See waveform 14)
A74-31 (ELS1) - B84-104 (E1) R - W-B Electric load Tail light switch on 7.5 to 14 V
Tail light switch off Below 1.5 V
A74-33 (ELS2) - B84-104 (E1) G - W-B Electric load Defogger switch on 7.5 to 14 V
Defogger switch off Below 1.5 V
A74-21 (FANL) - B84-104 (E1) R - W-B Cooling fan relay Ignition switch ON
Cooling fan not operated
11 to 14 V
Idling with A/C ON
or
High engine coolant temperature
Cooling fan operated
Below 1.5 V
A74-22 (FANH) - B84-104 (E1) G - W-B Cooling fan relay No. 2 Idling with high engine coolant temperature
Cooling fan operated at high speed
Below 1.5 V
B84-50 (ALT) - B84-104 (E1) G - W-B Generator assembly Ignition switch ON 11 to 14 V
A74-28 (IGSW) - B84-104 (E1) R - W-B Ignition switch assembly Ignition switch ON 11 to 14 V
A74-44 (MREL) - B84-104 (E1) GR - W-B EFI relay Ignition switch ON 11 to 14 V

*1: for Manual Transaxle

*2: for Automatic Transaxle

WAVEFORM 1


A369820E02
2.719,0.125 3.354,0.323 0.635,0.198 10 false 5 V/DIV. 2.844,0.938 3.229,1.115 0.385,0.177 10 false GND 2.854,1.375 3.24,1.552 0.385,0.177 10 false GND 0.292,0.865 0.635,1.26 0.344,0.396 10 false CH1 (IGT) 0.292,1.281 0.635,1.677 0.344,0.396 10 false CH2 (IGF) 1.333,1.875 2.427,2.073 1.094,0.198 10 false 10 ms./DIV.

Igniter Signal (IGT and IGF signal)
ECM Terminal Name CH1: Between IGT (1 to 4) and E1
CH2: Between IGF1 and E1
Tester Range 5 V/DIV., 10 ms./DIV.
Condition Idling

HINT:

The wavelength becomes shorter as the engine speed increases.



WAVEFORM 2


A063955E78
2.792,0.615 3.188,0.813 0.396,0.198 10 false GND 2.802,1.417 3.125,1.594 0.323,0.177 10 false GND 0.188,0.49 0.552,0.698 0.365,0.208 10 false CH1 0.063,0.667 0.573,0.844 0.51,0.177 10 false (VV1+) 0.167,1.281 0.5,1.458 0.333,0.177 10 false CH2 0.115,1.458 0.573,1.635 0.458,0.177 10 false (NE+) 1.188,1.917 2.073,2.094 0.885,0.177 10 false 20 ms./DIV. 2.656,0.094 3.271,0.292 0.615,0.198 10 false 5 V/DIV.

Crankshaft Position Sensor and Camshaft Position Sensor Signal
ECM Terminal Name CH1: Between VV1+ and NE-
CH2: Between NE+ and NE-
Tester Range 5 V/DIV., 20 ms./DIV.
Condition Idling with warm engine

HINT:

The wavelength becomes shorter as the engine speed increases.



WAVEFORM 3


A369420E02
0.5,0.198 1.208,0.406 0.708,0.208 10 false 20 V/DIV. 0.604,1.542 0.979,1.74 0.375,0.198 10 false GND 1.792,1.875 2.625,2.094 0.833,0.219 10 false 20 ms./DIV.

Fuel Injector Assembly Injection Signal
ECM Terminal Name Between #10 (to #40) and E01
Tester Range 20 V/DIV., 20 ms./DIV.
Condition Idling

HINT:

The wavelength becomes shorter as the engine speed increases.



WAVEFORM 4


A381766E01
1.125,1.948 2.073,2.156 0.948,0.208 10 false 200 ms./DIV. 2.823,1.625 3.219,1.813 0.396,0.188 10 false GND 2.521,0.01 3.406,0.177 0.885,0.167 10 false 200 mV/DIV.

Heated Oxygen Sensor (sensor 1) Signal
ECM Terminal Name Between OX1A and EX1A
Tester Range 200 mV/DIV., 200 ms./DIV.
Condition Engine speed maintained at 2500 rpm for 2 minutes after warming up sensor

HINT:

In the Data List, the items O2S B1S1 show the ECM input values of the heated oxygen sensor (sensor 1).



WAVEFORM 5


U158043E02
0.229,0.104 1.104,0.281 0.875,0.177 10 false 200 mV/DIV. 0.594,1.375 0.979,1.573 0.385,0.198 10 false GND 1.552,1.865 2.521,2.042 0.969,0.177 10 false 200 ms./DIV.

Heated Oxygen Sensor (sensor 2) Signal
ECM Terminal Name Between OX1B and EX1B
Tester Range 200 mV/DIV., 200 ms./DIV.
Condition Engine speed maintained at 2500 rpm for 2 minutes after warming up sensor

HINT:

In the Data List, the items O2S B1S2 show the ECM input values of the heated oxygen sensor (sensor 2).



WAVEFORM 6


A381767E01
2.802,0.99 3.26,1.188 0.458,0.198 10 false GND 2.604,0.198 3.26,0.438 0.656,0.24 10 false 1 V/DIV 1.573,1.604 2.313,1.813 0.74,0.208 10 false 1 ms./DIV

Knock Sensor Signal
ECM Terminal Name Between KNK1 and EKNK
Tester Range 1 V/DIV., 1 ms./DIV.
Condition Engine speed maintained at 4000 rpm after warming up engine

HINT:
·

The wavelength becomes shorter as engine speed increases.

·

The waveforms and amplitudes displayed differ slightly depending on the vehicle.




WAVEFORM 7


A365942E03
2.729,0.083 3.323,0.271 0.594,0.188 10 false 5 V/DIV. 2.885,1.24 3.26,1.417 0.375,0.177 10 false GND 1.656,1.708 2.458,1.896 0.802,0.188 10 false 20 ms./DIV.

Vehicle Speed Signal
ECM Terminal Name Between SPD and E1
Tester Range 5 V/DIV., 20 ms./DIV.
Condition Driving at 20 km/h (12 mph)

HINT:

The wavelength becomes shorter as the vehicle speed increases.



WAVEFORM 8


A208000E12
2.856,0.973 3.187,1.119 0.331,0.147 10 GND 2.631,0.216 3.176,0.36 0.545,0.144 10 5 V/DIV. 0.501,0.616 0.722,0.759 0.221,0.143 10 M+ 1.323,1.806 1.995,1.965 0.672,0.159 10 1 ms./DIV.

Throttle Actuator Positive Terminal Signal
ECM Terminal Name Between M+ and ME01
Tester Range 5 V/DIV., 1 ms./DIV.
Condition Idling with warm engine

HINT:

The duty ratio varies depending on the throttle actuator operation.



WAVEFORM 9


A245848E14
2.849,0.99 3.182,1.142 0.333,0.151 10 GND 2.627,0.266 3.166,0.409 0.539,0.142 10 5 V/DIV. 0.479,0.626 0.664,0.777 0.184,0.15 10 M- 1.323,1.82 1.996,1.967 0.672,0.147 10 1 ms./DIV.

Throttle Actuator Negative Terminal Signal
ECM Terminal Name Between M- and ME01
Tester Range 5 V/DIV., 1 ms./DIV.
Condition Idling with warm engine

HINT:

The duty ratio varies depending on the throttle actuator operation.



WAVEFORM 10


A205411E04
2.604,0.245 3.229,0.405 0.625,0.16 10 10 V/DIV. 0.469,1.906 1.225,2.084 0.756,0.178 10 20 ms./DIV. 2.681,1.03 3.05,1.202 0.369,0.172 10 GND

Purge VSV Signal
ECM Terminal Name Between PRG and E01
Tester Range 10 V/DIV., 20 ms./DIV.
Condition Idling, under purge control

HINT:

If the waveform is not similar to the illustration, check the waveform again after idling for 10 minutes or more.



WAVEFORM 11


A365942E01
2.729,0.083 3.323,0.271 0.594,0.188 10 false 5 V/DIV. 2.885,1.24 3.26,1.417 0.375,0.177 10 false GND 1.729,1.792 2.531,1.979 0.802,0.188 10 false 10 ms./DIV.

Engine Speed Signal
ECM Terminal Name Between TACH and E1
Tester Range 5 V/DIV., 10 ms./DIV.
Condition Idling

HINT:

The wavelength becomes shorter as the engine speed increases.



WAVEFORM 12


U158044E02
0.448,0.167 1.135,0.365 0.688,0.198 10 false 5 V/DIV. 0.521,1.115 0.958,1.313 0.438,0.198 10 false GND 1.75,1.844 2.813,2.042 1.063,0.198 10 false 1 ms./DIV.

Camshaft Timing Oil Control Valve (OCV) Signal
ECM Terminal Name Between OC1+ and OC1-
Tester Range 5 V/DIV., 1 ms./DIV.
Condition Idling


WAVEFORM 13


A357201E01
2.979,1.396 3.385,1.594 0.406,0.198 10 false GND 2.76,0.292 3.323,0.479 0.563,0.188 10 false 1 V/DIV. 1.469,1.896 2.26,2.083 0.792,0.188 10 false 10 μs./DIV.

CAN Communication Signal (Reference)
ECM Terminal Name Between CANH and E1
Tester Range 1 V/DIV., 10 μs./DIV.
Condition Ignition switch ON

HINT:

The waveform varies depending on the CAN communication signal.



WAVEFORM 14


A357202E01
3.01,1.354 3.385,1.531 0.375,0.177 10 false GND 2.771,0.229 3.385,0.417 0.615,0.188 10 false 1 V/DIV. 1.448,1.865 2.354,2.063 0.906,0.198 10 false 10 μs./DIV.

CAN Communication Signal (Reference)
ECM Terminal Name Between CANL and E1
Tester Range 1 V/DIV., 10 μs./DIV.
Condition Ignition switch ON

HINT:

The waveform varies depending on the CAN communication signal.