Home › Engine / Hybrid System › 1NZ-FE ENGINE CONTROL › IGNITION COIL AND SPARK PLUG › 2011.08–2016.09
RM19S0E _51 Engine / Hybrid System _051448 1NZ-FE ENGINE CONTROL _0248048 IGNITION COIL AND SPARK PLUG A

1NZ-FE ENGINE CONTROL  IGNITION COIL AND SPARK PLUG  INSTALLATION  


PROCEDURE

Hide 19100P 1.INSTALL SPARK PLUG

a.

Using a 16 mm spark plug wrench, install the 4 spark plugs.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)

NOTICE:

If a component has been dropped or subjected a strong impact, replace it.



Hide 2.INSTALL PLUG CAP

a.
U134210E01
0.684,2.275 1.416,1.76 false 2.692,2.779 1.83,2.108 false 0.593,2.314 1.037,2.634 0.443,0.320 10 *a 2.608,2.797 3.083,3.021 0.475,0.225 10 *1

Clean the plug cap fitting of the No. 1 ignition coil.

Text in Illustration
*1 Plug Cap
*a Plug Cap Fitting

NOTICE:

Foreign matter adhering to the plug cap fitting can cause high-voltage electrical leakage.



b.

Install a new plug cap to the No. 1 ignition coil.

NOTICE:
·

Make sure the plug cap is fully inserted all the way to section A.

·

When installing the plug cap, do not allow any foreign matter to adhere to the plug cap or plug cap fitting.

·

When installing the plug cap, be careful not to damage the plug cap or plug cap fitting.



HINT:

Allowing any foreign matter to adhere to the contact surfaces, or damaging the plug cap or fitting, can result in high-voltage electrical leakage.


A314957E04
6.104,1.865 5.802,1.208 false 5.271,2.271 4.198,0.979 false 3.833,1.979 4.021,1.031 false 3.042,2.302 2.719,0.948 false 2.198,1.948 2.333,1.104 false 1.469,2.365 1.104,1.479 false 0.438,2.073 0.917,1.083 false 0.365,2.104 0.708,2.292 0.344,0.188 10 false *1 2.125,1.969 2.344,2.177 0.219,0.208 10 false *b 3.75,1.948 4.271,2.24 0.521,0.292 10 false *c 1.396,2.385 1.625,2.583 0.229,0.198 10 false *a 2.979,2.344 3.49,2.531 0.51,0.188 10 false *2 5.208,2.281 5.958,2.5 0.75,0.219 10 false *d 6.063,1.906 6.417,2.104 0.354,0.198 10 false *1

Text in Illustration
*1 Spring *2 Inner Tube
*a Area with Talc Applied *b Inner Tube is Pinched
*c Inner Tube is Deformed *d Spring is Pinched

NOTICE:
·

When installing the plug cap, make sure not to pinch the inner tube.

·

When installing the plug cap, make sure the spring is not pinched by the inner tube.

·

After installing the plug cap, look through the tip of the plug cap into the interior and check that the inner tube and spring are not pinched or deformed.



HINT:

If there is any pinching or deformation of the inner tube or spring, the electrical connection between the spring and spark plug terminal will be poor, which can result in engine misfires and DTC output.


NOTICE:

When installing the plug cap, do not remove the talc (white powder) that has been applied to the inner surfaces of the plug cap.


HINT:

If the amount of talc applied is insufficient, this may cause the plug cap and spark plug to become stuck together in the future.


NOTICE:

When installing the plug cap or spark plug, do not apply oil or grease to the engagement surfaces of the plug cap or spark plug.


HINT:

Applying any oil or grease can cause the plug cap to deteriorate, resulting in high-voltage electrical leakage.



Hide 19500D 3.INSTALL NO. 1 IGNITION COIL

a.

Install the 4 No. 1 ignition coils with the 4 bolts.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)

NOTICE:
A268161E01
2.268,1.59 2.463,1.785 0.195,0.195 10 *2 2.268,0.696 2.463,0.891 0.195,0.195 10 *1

If the body or cap of the ignition coil is dropped or subjected to a strong impact, replace the ignition coil with a new one.


Text in Illustration
*1 Body
*2 Cap


b.

Connect the 4 No. 1 ignition coil connectors.