Home › Engine / Hybrid System › 1NZ-FE ENGINE CONTROL › INTEGRATION RELAY
RM19S0E _51 Engine / Hybrid System _051448 1NZ-FE ENGINE CONTROL _0248053 INTEGRATION RELAY G

1NZ-FE ENGINE CONTROL  INTEGRATION RELAY  INSPECTION  


PROCEDURE

Hide 82641 1.INSPECT NO. 1 INTEGRATION RELAY

a.

Check the EFI MAIN relay.

i.
U126317E02
0.958,0.354 1.25,0.51 0.292,0.156 10 false 1E 1.917,0.354 2.208,0.51 0.292,0.156 10 false 1D 2.646,0.354 2.938,0.51 0.292,0.156 10 false 1C 0.094,0.063 0.354,0.26 0.26,0.198 10 false *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1C-1 - 1E-4 Battery voltage not applied between 1E-10 - 1D-7 terminals 10 kΩ or higher
Battery voltage applied between 1E-10 - 1D-7 terminals Below 1 Ω


Text in Illustration
*a Component without harness connected
(No. 1 Integration Relay)

If the result is not as specified, replace the EFI MAIN relay.



b.

Check the C/OPN relay.

i.
U126317E02
0.958,0.354 1.25,0.51 0.292,0.156 10 false 1E 1.917,0.354 2.208,0.51 0.292,0.156 10 false 1D 2.646,0.354 2.938,0.51 0.292,0.156 10 false 1C 0.094,0.063 0.354,0.26 0.26,0.198 10 false *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1E-4 - 1E-5 Battery voltage not applied between 1E-11 - 1D-9 terminals 10 kΩ or higher
Battery voltage applied between 1E-11 - 1D-9 terminals Below 1 Ω


Text in Illustration
*a Component without harness connected
(No. 1 Integration Relay)

If the result is not as specified, replace the C/OPN relay.



c.

Check the IG2 relay.

i.
U126317E02
0.958,0.354 1.25,0.51 0.292,0.156 10 false 1E 1.917,0.354 2.208,0.51 0.292,0.156 10 false 1D 2.646,0.354 2.938,0.51 0.292,0.156 10 false 1C 0.094,0.063 0.354,0.26 0.26,0.198 10 false *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1C-1 - 1D-9 Battery voltage not applied between 1E-10 - 1D-17 terminals 10 kΩ or higher
Battery voltage applied between 1E-10 - 1D-17 terminals Below 1 Ω


Text in Illustration
*a Component without harness connected
(No. 1 Integration Relay)

If the result is not as specified, replace the IG2 relay.



d.

Check the HORN relay.

i.
U126317E02
0.958,0.354 1.25,0.51 0.292,0.156 10 false 1E 1.917,0.354 2.208,0.51 0.292,0.156 10 false 1D 2.646,0.354 2.938,0.51 0.292,0.156 10 false 1C 0.094,0.063 0.354,0.26 0.26,0.198 10 false *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1C-1 - 1E-7 Battery voltage not applied between 1C-1 - 1D-18 terminals 10 kΩ or higher
Battery voltage applied between 1C-1 - 1D-18 terminals Below 1 Ω


Text in Illustration
*a Component without harness connected
(No. 1 Integration Relay)

If the result is not as specified, replace the HORN relay.