Home › Engine / Hybrid System › 2NZ-FE ENGINE CONTROL › SFI SYSTEM › 2014.07–2016.09
RM19S0E _51 Engine / Hybrid System _051449 2NZ-FE ENGINE CONTROL _0248054 SFI SYSTEM J

2NZ-FE ENGINE CONTROL  SFI SYSTEM  ECM Power Source Circuit  


DESCRIPTION

When the ignition switch is turned to ON, the battery voltage is applied to the IGSW terminal of the ECM. The output signal from the MREL terminal of the ECM causes a current to flow to the EFI MAIN relay coil, closing the EFI MAIN relay contacts and supplying power to terminal +B and +B2 of the ECM.

WIRING DIAGRAM

A254094E06
6.079,5.301 6.269,5.455 0.189,0.155 10 E1 6.079,4.726 6.491,4.870 0.412,0.144 10 MREL 6.079,4.301 6.375,4.445 0.296,0.144 10 +B2 6.079,3.855 6.278,3.999 0.199,0.144 10 +B 6.079,2.961 6.476,3.105 0.397,0.144 10 IGSW 5.721,5.288 5.996,5.429 0.275,0.141 10 B84 5.721,4.72 5.996,4.861 0.275,0.141 10 A74 5.721,4.28 5.996,4.420 0.275,0.141 10 A74 5.721,3.845 5.996,3.985 0.275,0.141 10 A74 4.493,2.967 4.704,3.108 0.211,0.141 10 1D 4.493,4.291 4.704,4.432 0.211,0.141 10 1E 4.493,4.716 4.704,4.857 0.211,0.141 10 1D 1.686,2.963 1.892,3.104 0.206,0.141 10 1C 1.688,4.719 1.884,4.860 0.195,0.141 10 1E 3.965,2.668 4.181,2.808 0.216,0.141 10 1D 5.721,2.964 5.996,3.105 0.275,0.141 10 A74 0.591,4.998 1.059,5.149 0.468,0.151 10 Battery 0.444,4.097 0.815,4.246 0.371,0.149 10 MAIN 0.81,3.11 1.014,3.254 0.205,0.144 10 R/I 1.705,4.509 1.891,4.658 0.186,0.149 10 10 1.749,2.772 1.845,2.921 0.096,0.149 10 1 2.86,3.539 3.107,3.688 0.246,0.149 10 IG2 3.597,3.081 3.848,3.235 0.251,0.154 10 IG2 2.508,4.41 3.134,4.554 0.626,0.144 10 EFI MAIN 3.183,4.958 3.816,5.115 0.633,0.158 10 EFI MAIN 4.544,4.512 4.647,4.661 0.103,0.149 10 7 4.544,4.078 4.647,4.227 0.103,0.149 10 4 4.544,2.775 4.647,2.924 0.103,0.149 10 9 3.68,2.665 3.859,2.814 0.179,0.149 10 17 1.409,1.447 1.725,1.598 0.316,0.151 10 AM2 2.302,1.822 3.452,2.145 1.150,0.323 10 Ignition Switch Assembly 3.069,1.229 3.316,1.371 0.247,0.142 10 IG2 2.34,1.227 2.646,1.371 0.306,0.144 10 AM2 2.501,5.425 4.017,5.598 1.516,0.172 10 No. 1 Integration Relay 5.726,5.099 5.977,5.245 0.251,0.145 10 104 5.766,4.532 5.938,4.677 0.172,0.145 10 44 5.805,4.095 5.899,4.241 0.095,0.145 10 1 5.805,3.644 5.899,3.789 0.095,0.145 10 2 5.766,2.778 5.938,2.923 0.172,0.145 10 28 6.319,6.009 6.660,6.165 0.341,0.156 10 ECM 2.2,1.221 2.309,1.382 0.110,0.161 10 5 3.371,1.213 3.485,1.368 0.114,0.154 10 6 2.3,1.647 2.589,1.830 0.289,0.183 10 F13

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

After turning ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



PROCEDURE

1.CHECK TERMINAL VOLTAGE (POWER SOURCE OF NO. 1 INTEGRATION RELAY)
U126247E02
0.26,0.135 0.479,0.323 0.219,0.188 10 false *a 0.656,1.115 0.938,1.302 0.281,0.188 10 false 1C

a.

Remove the No. 1 integration relay from the engine room relay block.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
1C-1 - Body ground Always 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to No. 1 Integration Relay)



OK

2.INSPECT NO.1 INTEGRATION RELAY (EFI MAIN RELAY AND IG2 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (NO. 1 INTEGRATION RELAY - BATTERY)

2.INSPECT NO.1 INTEGRATION RELAY (EFI MAIN RELAY AND IG2 RELAY)
a.

Inspect the No. 1 integration relay (See page Engine / Hybrid System>2NZ-FE ENGINE CONTROL>INTEGRATION RELAY>INSPECTION).



OK

3.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - ECM)

NG

3.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - ECM)
a.

Remove the No. 1 integration relay from the engine room relay block.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A74-44 (MREL) - 1D-7 Always Below 1 Ω
A74-2 (+B) - 1E-4 Always Below 1 Ω
A74-1 (+B2) - 1E-4 Always Below 1 Ω
A74-44 (MREL) or 1D-7 - Body ground Always 10 kΩ or higher
A74-2 (+B) or 1E-4 - Body ground Always 10 kΩ or higher
A74-1 (+B2) or 1E-4 - Body ground Always 10 kΩ or higher




OK

4.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)
a.

Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B84-104 (E1) - Body ground Always Below 1 Ω




OK

5.INSPECT ECM (IGSW TERMINAL VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT ECM (IGSW TERMINAL VOLTAGE)
a.
U158078E02
2.854,3.021 2.302,3.344 false 2.042,1.469 2.313,1.865 false 2.875,2.906 3.354,3.125 0.479,0.219 10 false IGSW 0.094,0.083 0.302,0.26 0.208,0.177 10 false *a 0.083,2.344 0.292,2.521 0.208,0.177 10 false *b 0.354,3.198 0.677,3.385 0.323,0.188 10 false A74 0.667,0.323 0.948,0.5 0.281,0.177 10 false B84 2.281,1.865 2.573,2.073 0.292,0.208 10 false E1

Disconnect the ECM connectors.


b.

Turn the ignition switch assembly to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A74-28 (IGSW) - B84-104(E1) Ignition switch ON 11 to 14 V



Text in Illustration
*a Front view of wire harness connector
(to ECM)
*b Front view of wire harness connector
(to ECM)

Result
Result Proceed to
NG A
OK B


A

6.CHECK HARNESS AND CONNECTOR (ECM - NO. 1 INTEGRATION RELAY)

B

6.CHECK HARNESS AND CONNECTOR (ECM - NO. 1 INTEGRATION RELAY)
a.

Remove the No. 1 integration relay from the engine room relay block.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A74-28 (IGSW) - 1D-9 Always Below 1 Ω
A74-28 (IGSW) or 1D-9 - Body ground Always 10 kΩ or higher




OK

7.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH ASSEMBLY - NO. 1 INTEGRATION RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH ASSEMBLY - NO. 1 INTEGRATION RELAY - BODY GROUND)
a.

Remove the No. 1 integration relay from the engine room relay block.


b.

Disconnect the ignition switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1D-17 - F13-6 (IG2) Always Below 1 Ω
1E-10 - Body ground Always Below 1 Ω
F13-6 (IG2) or 1D-17 - Body ground Always 10 kΩ or higher




OK

8.INSPECT IGNITION SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT IGNITION SWITCH ASSEMBLY
a.

Inspect the ignition switch assembly (See page Engine / Hybrid System>2NZ-FE STARTING>IGNITION SWITCH>INSPECTION).



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (IGNITION SWITCH ASSEMBLY - BATTERY)

NG

REPLACE IGNITION SWITCH ASSEMBLY