Home › Engine / Hybrid System › 2NZ-FE ENGINE CONTROL › SFI SYSTEM › 2011.08–2014.07
RM19S0E _51 Engine / Hybrid System _051449 2NZ-FE ENGINE CONTROL _0248054 SFI SYSTEM C

2NZ-FE ENGINE CONTROL  SFI SYSTEM  P0136  Oxygen Sensor Circuit Malfunction (Bank 1 Sensor 2)  


DESCRIPTION

Refer to P0031 (See page Engine / Hybrid System>2NZ-FE ENGINE CONTROL>SFI SYSTEM>P0031).

HINT:

Sensor 2 refers to the sensor mounted behind the Three-Way Catalytic Converter (TWC) and located far from the engine assembly.


DTC No. DTC Detection Condition Trouble Area
P0136 Following conditions (a) and (b) met for 4 minutes or more after engine warmed up (2 trip detection logic):

(a) Vehicle driven in 1 STOP-and-GO* cycles

(b) Heated oxygen sensor (sensor 2) voltage remains at 0.4 V or more or 0.5 V or less.


·

Open or short in heated oxygen sensor (sensor 2) circuit

·

Heated oxygen sensor (sensor 2)

·

Heated oxygen sensor (sensor 2) heater

·

No. 1 integration relay (EFI relay)


All of following conditions (a), (b), (c), (d) and (e) met (2 trip detection logic):

(a) Cumulative sensor monitoring time 85 seconds or more

(b) Cumulative time while rear heated oxygen sensor voltage less than 0.05 V 60 seconds or more

(c) Cumulative time while rear heated oxygen sensor voltage 0.7 V or more less than 17 seconds

(d) Cumulative time while rear heated oxygen sensor voltage 0.45 V or more less than 17 seconds

(e) Maximum continuous time while rear heated oxygen sensor voltage 0.45 V or more less than 20 seconds



HINT:

*: STOP refers to a vehicle speed of less than 5 km/h (3.1 mph) and GO refers to a vehicle speed of 100 km/h (62.5 mph) or more.


MONITOR DESCRIPTION

The ECM monitors the heated oxygen sensor (sensor 2) to check for the following malfunctions. If any of the malfunctions are detected, the ECM illuminates the MIL and stores a DTC.

·

The heated oxygen sensor (sensor 2) output voltage remains above 0.5 V (rich) or below 0.4 V (lean) while the vehicle is accelerated and decelerated for 4 minutes or more.

·

The heated oxygen sensor (sensor 2) output voltage remains extremely low, below 0.05 V for a long time period of time while the vehicle is driven.


MONITOR STRATEGY

Required Sensor/Components (Main) Heated oxygen sensor (sensor 2)
Required Sensor/Components (Related) Engine coolant temperature sensor, Mass air flow meter, vehicle speed sensor, Throttle with motor body assembly
Frequency of operation Once per driving cycle

TYPICAL ENABLING CONDITIONS

Heated oxygen sensor output voltage:
All of the following conditions A to C are met -
A. Engine Running
B. Time after engine starts 0 seconds or more
C. Cumulative time while heated oxygen sensor is ON 22 seconds or more

Heated oxygen sensor output voltage (crack):
All of the following conditions A to E are met -
A. Engine Running
B. Vehicle speed 3 km/h (1.864 mph) or higher
C. Idle OFF
D. Fuel cut OFF
E. Cumulative time while heated oxygen sensor heater is ON 120 seconds or more

TYPICAL MALFUNCTION THRESHOLDS

Heated oxygen sensor output voltage
All of the following conditions are met -
Frequency of switch time between less than 0.4 V and 0.5 V or more 0 times
Cumulative rear oxygen sensor monitor time 190 seconds or more

Heated oxygen sensor output voltage (crack)
All of the following conditions A to E are met -
A. Cumulative heated oxygen sensor monitoring time 85 seconds or more
B. Cumulative time while heated oxygen sensor voltage is below 0.05 V 60 seconds or more
C. Cumulative time while heated oxygen sensor voltage is 0.7 V or higher Less than 17 seconds
D. Cumulative time while heated oxygen sensor voltage is 0.45 V or higher Less than 17 seconds
E. Maximum time while heated oxygen sensor voltage is 0.45 V or higher Less than 20 seconds

CONFIRMATION DRIVING PATTERN

A260198E01
0.02,0.546 1.377,0.744 1.357,0.198 10 100 km/h (62.5 mph) 0.972,2.003 1.406,2.215 0.434,0.211 10 Idling 0.188,2.36 1.377,2.572 1.190,0.211 10 Ignition switch ON 1.935,3.04 3.255,3.244 1.319,0.205 10 60 seconds or more 3.725,3.04 4.999,3.248 1.274,0.208 10 5 minutes or more 5.624,3.04 6.391,3.369 0.767,0.330 10 10 seconds or more 2.401,1.919 2.682,2.138 0.281,0.218 10 [A] 4.202,0.434 4.562,0.698 0.361,0.264 10 [B] 6.023,1.919 6.262,2.158 0.239,0.239 10 [C] 6.345,3.53 6.571,3.714 0.225,0.184 10 [D]

1.

Connect the intelligent tester to the DLC3.

2.

Turn the ignition switch on and turn the tester on.

3.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch and turn the tester on.

6.

Start the engine and idle it for 60 seconds or more [A].

7.

Drive the vehicle at more than 100 km/h (62.5 mph) for 5 minutes or more [B].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


8.

Allow the engine to idle for 10 seconds or more [C].

9.

Enter the following menus: Powertrain / Engine and ECT / DTC [D].

10.

Read pending DTC.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

12.

Input the DTC: P0136.

13.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [B] through [F].




WIRING DIAGRAM

CAUTION / NOTICE / HINT

HINT:

Malfunctioning areas can be identified by performing the Control the Injection Volume function provided in the Active Test. The Control the Injection Volume function can help to determine whether the heated oxygen sensor and other potential trouble areas are malfunctioning.

The following instructions describe how to conduct the Control the Injection Volume operation using the intelligent tester.

1.

Connect the intelligent tester to the DLC3.

2.

Start the engine and turn the tester on.

3.

Warm up the engine and run the engine at an engine speed of 2500 rpm for approximately 90 seconds.

4.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume.

5.

Perform the Active Test operation with the engine idling.

6.

Monitor the output voltages of the heated oxygen sensors (O2S B1S1 and O2S B1S2) displayed on the tester.



HINT:
·

Change the fuel injection volume within the range of -12% to +12%. The injection volume can be changed in fine gradations.

·

Each sensor reacts in accordance with increases and decreases in the fuel injection volume.



Tester Display
(Sensor)
Injection Volume Status Voltage
O2S B1S1
(Heated oxygen sensor (sensor 1))
+12% Rich Higher than 0.5 V
-12% Lean Below 0.4 V
O2S B1S2
(Heated oxygen sensor (sensor 2))
+12% Rich Higher than 0.5 V
-12% Lean Below 0.4 V

NOTICE:

The heated oxygen sensor (sensor 1) has an output delay of a few seconds and the heated oxygen sensor (sensor 2) has a maximum output delay of approximately 20 seconds.


A382692E04
0.115,0.552 0.5,0.76 0.385,0.208 10 false Case 0.625,0.438 2.823,0.802 2.198,0.365 10 false Heated Oxygen Sensor (Sensor 1) Output Voltage 5.948,0.479 7.01,0.875 1.063,0.396 10 false Main Suspected Trouble Area 0.219,2.208 0.438,2.448 0.219,0.24 10 false 1 0.583,1.333 1.625,1.615 1.042,0.281 10 false Injection Volume 3.25,2.25 4.219,2.552 0.969,0.302 10 false Output Voltage 1.458,1.604 1.854,1.813 0.396,0.208 8 false +12% 1.469,1.844 1.99,2.083 0.521,0.24 8 false -12% 3.563,2.583 4.542,2.74 0.979,0.156 8 false Higher than 0.5 V 1.188,2.865 1.938,3.01 0.75,0.146 8 false Below 0.4 V 3.25,1.333 4.292,1.615 1.042,0.281 10 false Injection Volume 0.583,2.25 1.552,2.552 0.969,0.302 10 false Output Voltage 4.042,1.583 4.563,1.823 0.521,0.24 8 false +12% 4.052,1.823 4.573,2.063 0.521,0.24 8 false -12% 0.948,2.615 1.969,2.865 1.021,0.25 8 false Higher than 0.5 V 3.813,2.823 4.531,2.99 0.719,0.167 8 false Below 0.4 V 6.469,2.167 6.656,2.427 0.188,0.26 10 false - 0.219,4.25 0.438,4.49 0.219,0.24 10 false 2 0.583,3.385 1.625,3.667 1.042,0.281 10 false Injection Volume 0.583,4.417 1.552,4.719 0.969,0.302 10 false Output Voltage 3.25,3.385 4.292,3.667 1.042,0.281 10 false Injection Volume 3.25,4.417 4.219,4.719 0.969,0.302 10 false Output Voltage 0.583,5.458 1.625,5.74 1.042,0.281 10 false Injection Volume 3.25,5.448 4.292,5.729 1.042,0.281 10 false Injection Volume 3.25,7.542 4.292,7.823 1.042,0.281 10 false Injection Volume 0.573,7.542 1.615,7.823 1.042,0.281 10 false Injection Volume 0.583,6.333 1.552,6.635 0.969,0.302 10 false Output Voltage 3.24,6.333 4.208,6.635 0.969,0.302 10 false Output Voltage 3.25,8.49 4.219,8.792 0.969,0.302 10 false Output Voltage 0.583,8.5 1.552,8.802 0.969,0.302 10 false Output Voltage 1.427,3.688 1.813,3.875 0.385,0.188 8 false +12% 4.063,3.677 4.438,3.854 0.375,0.177 8 false +12% 4.042,5.729 4.448,5.885 0.406,0.156 8 false +12% 1.375,5.74 1.771,5.927 0.396,0.188 8 false +12% 1.438,7.813 1.854,7.99 0.417,0.177 8 false +12% 4.073,7.802 4.448,7.979 0.375,0.177 8 false +12% 4.073,3.885 4.458,4.083 0.385,0.198 8 false -12% 1.438,3.896 1.958,4.135 0.521,0.24 8 false -12% 1.406,5.979 1.813,6.156 0.406,0.177 8 false -12% 4.052,5.948 4.427,6.135 0.375,0.188 8 false -12% 4.094,8.031 4.458,8.229 0.365,0.198 8 false -12% 1.458,8.01 1.833,8.188 0.375,0.177 8 false -12% 0.875,4.813 1.969,5.073 1.094,0.26 8 false Almost no reaction 2.594,2.75 2.844,2.958 0.25,0.208 8 false OK 5.177,2.719 5.427,2.927 0.25,0.208 8 false OK 2.542,4.729 2.792,4.938 0.25,0.208 8 false NG 5.198,4.823 5.448,5.031 0.25,0.208 8 false OK 3.781,4.927 4.521,5.083 0.74,0.156 8 false Below 0.4 V 3.542,4.677 4.49,4.865 0.948,0.188 8 false Higher than 0.5 V 0.885,6.75 1.854,6.927 0.969,0.177 8 false Higher than 0.5 V 1.125,6.99 1.885,7.146 0.76,0.156 8 false Below 0.4 V 3.5,6.865 4.594,7.125 1.094,0.26 8 false Almost no reaction 5.208,6.781 5.458,6.99 0.25,0.208 8 false NG 0.896,8.938 1.99,9.198 1.094,0.26 8 false Almost no reaction 2.542,8.865 2.792,9.073 0.25,0.208 8 false NG 5.208,8.875 5.458,9.083 0.25,0.208 8 false NG 3.51,8.938 4.604,9.198 1.094,0.26 8 false Almost no reaction 0.229,6.271 0.448,6.51 0.219,0.24 10 false 3 0.25,8.458 0.469,8.698 0.219,0.24 10 false 4 5.823,3.333 6.979,3.708 1.156,0.375 10 false - Heated oxygen sensor (Sensor 1) 5.865,3.865 6.969,4.396 1.104,0.531 10 false - Heated oxygen sensor heater (Sensor 1) 5.844,4.625 6.917,5.167 1.073,0.542 10 false - Heated oxygen sensor circuit (Sensor 1) 5.813,8.083 6.813,8.271 1,0.188 10 false - Fuel pressure 5.802,8.396 7.135,9.115 1.333,0.719 10 false - Gas leak from exhaust system (Air-fuel ratio extremely rich or lean) 5.865,7.479 6.781,7.854 0.917,0.375 10 false - Fuel injector assembly 5.813,5.406 6.969,5.781 1.156,0.375 10 false - Heated oxygen sensor (Sensor 2) 5.813,5.958 6.917,6.49 1.104,0.531 10 false - Heated oxygen sensor heater (Sensor 2) 5.833,6.667 6.906,7.208 1.073,0.542 10 false - Heated oxygen sensor circuit (Sensor 2) 3.271,0.427 5.469,0.792 2.198,0.365 10 false Heated Oxygen Sensor (Sensor 2) Output Voltage

HINT:
·

Following the Control the Injection Volume procedure enables technicians to check and graph the voltage outputs of both heated oxygen sensors

·

To display the graph, enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume / O2S B1S1 and O2S B1S2, then press the view button.

·

If the OX1B wire from the ECM connector is short-circuited to the +B wire, DTC P0136 will be stored.



NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0136)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / DTC.


d.

Read DTCs.

Result
Result Proceed to
DTC P0136 is output A
DTC P0136 and other DTCs are output B

HINT:

If any DTCs other than P0136 are output, troubleshoot those DTCs first.




A

2.READ VALUE USING INTELLIGENT TESTER (O2S B1S2)

B

2.READ VALUE USING INTELLIGENT TESTER (O2S B1S2)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / O2S B1S2.


d.

Allow the engine to run at 2500 rpm for 3 minutes.


e.

Depress the accelerator pedal quickly until the engine rpm reaches 4000 rpm 3 times.

Standard Voltage:

Heated oxygen sensor voltage alternates between below 0.4 V and higher than 0.5 V.



A128474E12
1.441,0.459 1.745,0.642 0.304,0.184 10 1 V 2.468,0.216 2.772,0.399 0.304,0.184 10 OK 3.422,0.216 3.726,0.399 0.304,0.184 10 NG 4.376,0.216 4.680,0.399 0.304,0.184 10 NG 5.33,0.216 5.634,0.399 0.304,0.184 10 NG 1.376,0.725 1.744,0.908 0.369,0.184 10 0.5 V 1.357,0.991 1.744,1.175 0.387,0.184 10 0.4 V 1.441,1.257 1.745,1.441 0.304,0.184 10 0 V

Result
Result Proceed to
NG A
OK B


A

3.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE OF HEATED OXYGEN SENSOR (SENSOR 2))

B

7.PERFORM CONFIRMATION DRIVING PATTERN
3.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE OF HEATED OXYGEN SENSOR (SENSOR 2))
a.


OK

4.CHECK TERMINAL VOLTAGE (POWER SOURCE OF HEATED OXYGEN SENSOR (SENSOR 2))

NG

4.CHECK TERMINAL VOLTAGE (POWER SOURCE OF HEATED OXYGEN SENSOR (SENSOR 2))
a.

Disconnect the heated oxygen sensor (sensor 2) connector.


b.

Turn the ignition switch to ON.


c.
U158079E02
1.948,0.927 2.313,0.646 false 1.083,0.156 1.313,0.344 0.229,0.188 10 false *a 0.573,0.979 0.854,1.156 0.281,0.177 10 false F80 2.375,0.5 2.677,0.698 0.302,0.198 10 false +B

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F80-2 (+B) - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Heated Oxygen Sensor (Sensor 2))



OK

5.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR (SENSOR 2) - ECM)

NG

6.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - HEATED OXYGEN SENSOR (SENSOR 2))
5.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR (SENSOR 2) - ECM)
a.

Disconnect the heated oxygen sensor (sensor 2) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F80-1 (HT1B) - B84-47 (HT1B) Always Below 1 Ω
F80-3 (OX1B) - B84-64 (OX1B) Always Below 1 Ω
F80-4 (E2) - B84-87 (EX1B) Always Below 1 Ω
F80-1 (HT1B) or B84-47 (HT1B) - Body ground Always 10 kΩ or higher
F80-3 (OX1B) or B84-64 (OX1B) - Body ground Always 10 kΩ or higher
F80-4 (E2) or B84-87 (EX1B) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - HEATED OXYGEN SENSOR (SENSOR 2))
a.

Disconnect the heated oxygen sensor (sensor 2) connector.


b.

Remove the No. 1 integration relay from the engine room relay block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F80-2 (+B) - 1D-11 Always Below 1 Ω
F80-2 (+B) or 1D-11 - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.PERFORM CONFIRMATION DRIVING PATTERN
a.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.



NEXT

8.CHECK WHETHER DTC OUTPUT RECURS
8.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / DTC.


d.

Read the DTCs.

Result
Result Proceed to
DTC P0136 is output A
DTC is not output B



A

B