Home › Engine / Hybrid System › 2NZ-FE ENGINE CONTROL › SFI SYSTEM › 2011.08–2014.07
RM19S0E _51 Engine / Hybrid System _051449 2NZ-FE ENGINE CONTROL _0248054 SFI SYSTEM C

2NZ-FE ENGINE CONTROL  SFI SYSTEM  P0031  Oxygen Sensor Heater Control Circuit Low (Bank 1 Sensor 1)  P0032  Oxygen Sensor Heater Control Circuit High (Bank 1 Sensor 1)  P0037  Oxygen Sensor Heater Control Circuit Low (Bank 1 Sensor 2)  P0038  Oxygen Sensor Heater Control Circuit High (Bank 1 Sensor 2)  


DESCRIPTION

The heated oxygen sensor is used to monitor the oxygen concentration in the exhaust gas. For optimum catalytic converter operation, the air-fuel mixture must be maintained near the ideal stoichiometric air-fuel ratio. The heated oxygen sensor output voltage changes suddenly in the vicinity of the stoichiometric air-fuel ratio. The ECM adjusts the fuel injection time so that the air-fuel ratio is nearly stoichiometric. The heated oxygen sensor generates a voltage between 0 and 1 V in response to the oxygen concentration in the exhaust gas.

If the oxygen concentration in the exhaust gas increases, the air-fuel ratio is described as lean. The heated oxygen sensor voltage drops to below 0.45 V and the heated oxygen sensor informs the ECM of the lean condition. If there is little oxygen in the exhaust gas, the air-fuel ratio is described as rich. The heated oxygen sensor voltage increases to above 0.45 V and the heated oxygen sensor informs the ECM of the rich condition.

A112653E01
0.241,2.312 0.669,2.478 0.428,0.167 10 Cover 0.952,2.387 0.655,2.387 false 1.311,2.442 2.2,2.618 0.89,0.176 10 Exhaust Gas 1.86,0.265 2.717,0.464 0.857,0.199 10 Atmosphere 3.394,0.34 3.98,0.549 0.586,0.209 10 Housing 3.444,0.665 4.683,0.836 1.239,0.171 10 Platinum Electrode 3.444,0.971 4.665,1.324 1.221,0.353 10 Solid Electrolyte (Zirconia Element) 3.444,1.864 3.951,2.04 0.507,0.176 10 Heater 3.444,2.147 4.632,2.355 1.188,0.209 10 Coating (Ceramic) 3.444,1.56 4.683,1.731 1.239,0.171 10 Platinum Electrode 4.113,0.335 5.096,0.53 0.983,0.195 10 Output Voltage 4.796,2.246 6.833,2.468 2.037,0.223 10 Richer - Air-fuel Ratio - Leaner 5.115,0.179 6.476,0.388 1.361,0.209 10 Ideal Air-fuel Mixture 3.37,0.411 3.116,0.651 false 3.426,1.036 2.881,1.036 false 3.422,0.722 2.858,0.902 false 3.425,1.63 2.902,1.484 false 3.422,1.932 2.769,1.7 false 3.43,2.213 2.873,1.901 false 2.32,2.117 1.771,2.425 false

HINT:
·

Sensor 1 refers to the sensor mounted in front of the Three-Way Catalytic Converter (TWC) and located near the engine assembly.

·

Sensor 2 refers to the sensor mounted behind the TWC and located far from the engine assembly.



A254131E01
4.561,1.606 4.973,1.746 0.413,0.140 10 OX1A 4.561,1.033 4.973,1.172 0.413,0.140 10 HT1A 5.168,2.755 5.581,2.895 0.413,0.140 10 MREL 5.168,2.176 5.581,2.315 0.413,0.140 10 EX1A 5.168,1.597 5.581,1.736 0.413,0.140 10 OX1A 5.168,1.033 5.581,1.172 0.413,0.140 10 HT1A 3.893,0.874 4.336,1.030 0.443,0.156 10 Heater 3.883,1.39 4.345,1.544 0.461,0.154 10 Sensor 2.119,2.422 2.909,2.598 0.790,0.176 10 EFI MAIN 0.47,1.047 0.973,1.402 0.503,0.355 10 from Battery 1.095,1.304 1.761,1.450 0.665,0.147 10 EFI MAIN 0.962,3.487 1.465,3.657 0.503,0.170 10 Ground 3.472,2.065 4.971,2.211 1.498,0.147 10 Heated Oxygen Sensor 3.449,1.598 3.654,1.747 0.205,0.149 10 E2 3.451,1.042 3.654,1.189 0.202,0.147 10 +B 0.063,0.066 2.534,0.250 2.471,0.184 10 Reference (System Diagram Sensor 1): 5.944,3.431 6.313,3.582 0.369,0.151 10 ECM

A259951E01
4.561,1.522 4.973,1.662 0.413,0.140 10 OX1B 4.561,0.949 4.973,1.088 0.413,0.140 10 HT1B 5.168,2.671 5.581,2.810 0.413,0.140 10 MREL 5.168,2.092 5.581,2.231 0.413,0.140 10 EX1B 5.168,1.513 5.581,1.652 0.413,0.140 10 OX1B 5.168,0.949 5.581,1.088 0.413,0.140 10 HT1B 3.893,0.79 4.336,0.946 0.443,0.156 10 Heater 3.883,1.305 4.345,1.459 0.461,0.154 10 Sensor 2.104,2.434 2.816,2.659 0.711,0.225 10 EFI MAIN 0.47,0.963 0.973,1.318 0.503,0.355 10 from Battery 1.095,1.22 1.761,1.366 0.665,0.147 10 EFI MAIN 0.962,3.403 1.465,3.573 0.503,0.170 10 Ground 3.472,1.981 4.971,2.127 1.498,0.147 10 Heated Oxygen Sensor 3.449,1.514 3.654,1.663 0.205,0.149 10 E2 3.451,0.958 3.654,1.105 0.202,0.147 10 +B 0.063,0 2.534,0.184 2.471,0.184 10 Reference (System Diagram Sensor 2): 5.944,3.347 6.313,3.498 0.369,0.151 10 ECM 2.926,1.247 3.619,1.459 0.693,0.211 10 EFI NO. 2

DTC No. DTC Detection Condition Trouble Area
P0031
P0037
Heated oxygen sensor heater current below 0.25 A when heater operates with +B greater than 10.5 V
(1 trip detection logic)
·

Open in Heated oxygen sensor heater circuit

·

Heated oxygen sensor heater

·

No. 1 integration relay (EFI MAIN relay)

·

ECM


P0032
P0038
Heated oxygen sensor heater current exceeds 2 A when heater operates
(1 trip detection logic)
·

Short in Heated oxygen sensor heater circuit

·

Heated oxygen sensor heater

·

No. 1 integration relay (EFI MAIN relay)

·

ECM



MONITOR DESCRIPTION

The sensing portion of the heated oxygen sensor has a zirconia element which is used to detect the oxygen concentration in the exhaust. If the zirconia element is at the proper temperature and the difference in the oxygen concentration between the inside and outside surface of the sensor is large, the zirconia element will generate voltage signals. In order to increase the oxygen concentration detecting capacity in the zirconia element, the ECM supplements the heat from the exhaust with heat from a heating element inside the sensor. When the current in the heated oxygen sensor heater is out of the standard operating range, the ECM interprets this as a fault in the heated oxygen sensor heater. The ECM illuminates the MIL and stores a DTC.

Example: The ECM stores either DTC P0032 or P0038 when the current in the heated oxygen sensor heater is more than 2 A despite the heater being OFF. Conversely, when the heater current is less than 0.25 A despite the heater being ON, DTC P0031 or P0037 is stored.

MONITOR STRATEGY

Required Sensors/Components (Main) Heated oxygen sensor heater
Required Sensors/Components (Related) Vehicle speed sensor
Frequency of Operation Continuous

TYPICAL ENABLING CONDITIONS

Battery voltage 10.5 V or more
Engine Running
Starter OFF

P0031 and P0037
Duration of following conditions 2 seconds or more
Learned heater current during heater OFF Completed

P0032 and P0038
Duration of following conditions 0.1 seconds or more
Learned heater current during heater OFF Completed

TYPICAL MALFUNCTION THRESHOLDS

P0031 and P0037
Heated oxygen sensor heater current when heated oxygen sensor heater ON Less than 0.25 A

P0032 and P0038
Heated oxygen sensor heater current when heated oxygen sensor heater OFF More than 2 A

COMPONENT OPERATING RANGE

Heated oxygen sensor heater current 0.25 to 2 A (when idling with warm engine and battery voltage 11 to 14 V)

CONFIRMATION DRIVING PATTERN

A198819E42
0.749,0.969 1.396,1.162 0.647,0.193 10 3000 rpm 0.946,1.739 1.352,1.900 0.406,0.161 10 Idling 0.21,2.006 1.419,2.344 1.209,0.338 10 Ignition Switch ON 1.926,2.132 2.161,2.297 0.235,0.165 10 [A] 2.762,1.622 2.955,1.815 0.193,0.193 10 [B] 4.026,0.868 4.283,1.006 0.258,0.137 10 [C] 5.39,1.6 5.613,1.782 0.223,0.181 10 [D] 2.272,2.589 3.465,2.745 1.193,0.156 10 5 minutes or more 4.873,2.608 6.066,2.764 1.193,0.156 10 5 minutes or more 3.85,2.617 4.423,2.782 0.573,0.165 10 1 minute 5.98,3.028 6.182,3.230 0.202,0.202 10 [E]

1.

Connect the intelligent tester to the DLC3.

2.

Turn the ignition switch to ON and turn the tester on.

3.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the tester on [A].

6.

Start the engine and idle it for 5 minutes or more [B].

7.

With the vehicle stationary, depress the accelerator pedal and maintain an engine speed of 3000 rpm for 1 minute [C].

8.

Idle the engine for 5 minutes or more [D].

9.

Enter the following menus: Powertrain / Engine and ECT / DTC [E].

10.

Read DTCs.

HINT:
·

If a DTC is output, the system is malfunctioning.

·

If a DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

12.

Input the DTC: P0031, P0032, P0037 or P0038.

13.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit




HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [B] through [E] again.



WIRING DIAGRAM

A254074E01
5.406,0.494 5.673,0.641 0.267,0.147 10 A74 5.403,1.167 5.675,1.304 0.272,0.137 10 B84 5.403,1.522 5.675,1.659 0.272,0.137 10 B84 5.403,2.026 5.675,2.163 0.272,0.137 10 B84 5.403,4.367 5.675,4.504 0.272,0.137 10 B84 5.403,3.867 5.675,4.005 0.272,0.137 10 B84 5.403,3.461 5.675,3.598 0.272,0.137 10 B84 5.778,0.483 6.260,0.652 0.482,0.170 10 MREL 5.778,1.078 6.156,1.215 0.378,0.137 10 HT1A 3.608,1.045 3.986,1.183 0.378,0.137 10 HT1A 5.761,1.41 6.166,1.556 0.406,0.147 10 OX1A 3.584,1.419 3.990,1.566 0.406,0.147 10 OX1A 5.742,1.923 6.120,2.098 0.378,0.174 10 EX1A 3.603,3.329 3.981,3.466 0.378,0.137 10 HT1B 5.755,3.741 6.152,3.888 0.397,0.147 10 OX1B 5.747,3.338 6.125,3.476 0.378,0.137 10 HT1B 3.58,3.745 3.976,3.891 0.397,0.147 10 OX1B 5.745,4.238 6.125,4.396 0.380,0.157 10 EX1B 3.771,1.895 3.979,2.060 0.207,0.165 10 E2 3.724,4.249 3.932,4.414 0.207,0.165 10 E2 4.051,1.055 4.147,1.197 0.096,0.142 10 1 3.001,1.05 3.103,1.204 0.103,0.154 10 2 4.065,3.754 4.175,3.891 0.110,0.137 10 3 4.068,4.244 4.173,4.386 0.105,0.142 10 4 4.058,3.334 4.154,3.476 0.096,0.142 10 1 3.013,3.34 3.116,3.493 0.103,0.154 10 2 4.065,1.414 4.175,1.552 0.110,0.137 10 3 4.065,1.902 4.170,2.044 0.105,0.142 10 4 2.886,2.463 4.426,2.822 1.540,0.359 10 Heated Oxygen Sensor (Sensor 1) 2.886,4.826 4.415,5.165 1.529,0.339 10 Heated Oxygen Sensor (Sensor 2) 5.168,5.494 6.022,5.676 0.854,0.182 10 *: Shielded 5.42,0.979 5.691,1.146 0.272,0.167 10 109 5.424,1.349 5.691,1.505 0.267,0.156 10 112 5.473,1.839 5.650,1.985 0.177,0.146 10 90 5.462,3.278 5.673,3.438 0.211,0.161 10 47 5.462,3.693 5.645,3.868 0.184,0.174 10 64 5.468,4.17 5.667,4.316 0.199,0.147 10 87 5.453,0.314 5.626,0.456 0.174,0.142 10 44 1.48,1.965 2.141,2.121 0.661,0.156 10 EFI MAIN 0.752,2.643 1.412,2.798 0.661,0.156 10 EFI MAIN 0.806,3.282 2.313,3.457 1.508,0.174 10 No. 1 Integration Relay 0.766,3.899 0.978,4.055 0.211,0.156 10 R/I 0.766,4.452 1.167,4.599 0.401,0.147 10 MAIN 0.717,1.143 1.113,1.487 0.397,0.343 10 EFI NO. 2 1.967,1.164 2.163,1.316 0.195,0.151 10 1E 1.967,2.512 2.163,2.663 0.195,0.151 10 1E 2.015,0.936 2.134,1.087 0.119,0.151 10 4 1.949,2.302 2.158,2.462 0.209,0.161 10 10 1.097,0.835 1.302,0.977 0.205,0.142 10 1D 0.552,0.83 0.747,0.982 0.195,0.151 10 1D 1.401,0.832 1.515,0.981 0.114,0.149 10 7 0.834,0.832 1.010,0.981 0.177,0.149 10 11 0.544,3.014 0.755,3.156 0.211,0.142 10 1C 0.848,3.011 0.948,3.187 0.100,0.176 10 1 0.946,5.006 1.421,5.183 0.475,0.177 10 Battery 2.886,2.306 3.223,2.518 0.336,0.211 10 B37 2.886,4.66 3.226,4.833 0.340,0.173 10 F80 6.153,5.14 6.522,5.305 0.369,0.165 10 ECM 3.178,3.337 3.397,3.499 0.219,0.162 10 +B 3.178,1.037 3.397,1.198 0.219,0.162 10 +B 4.574,4.094 4.749,4.268 0.174,0.174 10 * 4.574,1.768 4.749,1.942 0.174,0.174 10 *

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:
·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.

·

Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

Change the fuel injection volume using the Control the Injection Volume function provided in the Active Test and monitor the heated oxygen sensor output voltage (See page Engine / Hybrid System>2NZ-FE ENGINE CONTROL>SFI SYSTEM>P0130). If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.



PROCEDURE

1.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE)
a.

Inspect heated oxygen sensor.

HINT:
·

For the heated oxygen sensor (sensor 1) inspection, refer to the following procedures (See page Engine / Hybrid System>2NZ-FE ENGINE CONTROL>HEATED OXYGEN SENSOR(for Sensor 1)>INSPECTION).

·

For the heated oxygen sensor (sensor 2) inspection, refer to the following procedures (See page Engine / Hybrid System>1NZ-FE ENGINE CONTROL>HEATED OXYGEN SENSOR(for Sensor 2)>INSPECTION).





OK

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF HEATED OXYGEN SENSOR HEATER)

NG

NG

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF HEATED OXYGEN SENSOR HEATER)
a.
U158097E02
1.792,2.313 2.479,1.844 false 1.74,0.865 2.427,0.396 false 0.115,0.094 0.323,0.26 0.208,0.167 10 false *a 0.99,0.792 1.219,0.979 0.229,0.188 10 false *b 0.969,2.229 1.198,2.417 0.229,0.188 10 false *c 2.5,0.302 2.781,0.51 0.281,0.208 10 false +B 2.531,1.74 2.844,1.958 0.313,0.219 10 false +B 0.573,0.875 0.927,1.063 0.354,0.188 10 false B37 0.573,2.333 0.906,2.5 0.333,0.167 10 false F80

Disconnect the heated oxygen sensor (sensor 1 or 2) connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage (for sensor 1):
Tester Connection Switch Condition Specified Condition
B37-2 (+B) - Body ground Ignition switch ON 11 to 14 V


Standard Voltage (for sensor 2):
Tester Connection Switch Condition Specified Condition
F80-2 (+B) - Body ground Ignition switch ON 11 to 14 V



Text in Illustration
*a Front view of wire harness connector
(to Heated Oxygen Sensor)
*b for sensor 1
*c for sensor 2


OK

3.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM)

NG

5.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - NO. 1 INTEGRATION RELAY)
3.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM)
a.

Disconnect the heated oxygen sensor (sensor 1 or 2) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (for sensor 1):
Tester Connection Condition Specified Condition
B37-1 (HT1A) - B84-109 (HT1A) Always Below 1 Ω
B37-1 (HT1A) or B84-109 (HT1A) - Body ground Always 10 kΩ or higher


Standard Resistance (for sensor 2):
Tester Connection Condition Specified Condition
F80-1 (HT1B) - B84-47 (HT1B) Always Below 1 Ω
F80-1 (HT1B) or B84-47 (HT1B) - Body ground Always 10 kΩ or higher




OK

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0031, P0032, P0037 OR P0038)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0031, P0032, P0037 OR P0038)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.



d.

Start the engine.


e.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


f.

Enter the following menus: Powertrain / Engine and ECT / DTC.


g.

Read DTCs.

Result
Result Proceed to
DTC is not output A
DTC P0031, P0032, P0037 or P0038 are output B



A

B

5.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - NO. 1 INTEGRATION RELAY)
a.

Disconnect the heated oxygen sensor (sensor 1 or 2) connector.


b.

Remove the No. 1 integration relay from the engine room relay block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (for sensor 1):
Tester Connection Condition Specified Condition
B37-2 (+B) - 1E-4 Always Below 1 Ω
B37-2 (+B) or 1E-4 - Body ground Always 10 kΩ or higher


Standard Resistance (for sensor 2):
Tester Connection Condition Specified Condition
F80-2 (+B) - 1D-11 Always Below 1 Ω
F80-2 (+B) or 1D-11 - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR