Home › Engine / Hybrid System › 2NZ-FE ENGINE CONTROL › SFI SYSTEM › 2011.08–2014.07
RM19S0E _51 Engine / Hybrid System _051449 2NZ-FE ENGINE CONTROL _0248054 SFI SYSTEM C

2NZ-FE ENGINE CONTROL  SFI SYSTEM  P2121  Throttle / Pedal Position Sensor / Switch "D" Circuit Range / Performance  


DESCRIPTION

Refer to DTC P2120 (See page Engine / Hybrid System>2NZ-FE ENGINE CONTROL>SFI SYSTEM>P2120).

DTC No. DTC Detection Condition Trouble Area
P2121 Either of following conditions 1 or 2 met for 0.5 seconds (1 trip detection logic)
1.

Difference between VPA and VPA2 is less than 0.4 V, or more than 1.2 V. (learned value of accelerator off position)

2.

Difference between VPA and VPA2 is greater than or equal to the specified value.


·

Accelerator pedal sensor assembly

·

ECM



MONITOR DESCRIPTION

The accelerator pedal position sensor is mounted on the accelerator pedal bracket. The accelerator pedal position sensor has 2 sensor elements and 2 signal outputs: VPA and VPA2. VPA is used to detect the actual accelerator pedal angle (used for engine control) and VPA2 is used to detect malfunctions in VPA. When the difference between the output voltages of VPA and VPA2 deviates from the standard, the ECM determines that the accelerator pedal position sensor is malfunctioning. The ECM turns on the MIL and stores the DTC.

MONITOR STRATEGY

Required Sensors/Components Accelerator pedal sensor assembly
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

A199317E03
0.12,0.098 1.732,0.272 1.611,0.174 10 Accelerator Pedal State 0.865,0.418 1.583,0.567 0.719,0.149 10 Depressed 0.95,0.878 1.592,1.034 0.642,0.156 10 Released 0.432,2.405 1.636,2.575 1.205,0.170 10 Ignition Switch ON 2.092,2.489 2.290,2.673 0.198,0.184 10 [A] 4.414,3.434 4.632,3.611 0.218,0.177 10 [C] 5.364,1.69 6.006,1.846 0.642,0.156 10 Released 2.837,3.049 3.646,3.226 0.809,0.177 10 20 seconds 3.006,1.226 3.725,1.375 0.719,0.149 10 Depressed 3.868,1.129 4.058,1.306 0.191,0.177 10 [B] 3.634,2.007 2.767,1.303 2.767,1.303 2.93,1.303 false 4.728,2.416 5.116,1.774 5.116,1.774 5.261,1.774 false 2.59,2.008 3.232,2.164 0.642,0.156 10 Released 2.207,2.416 2.44,2.073 2.44,2.073 2.543,2.073 false

1.

Connect the intelligent tester to the DLC3.

2.

Turn the ignition switch to ON and turn the tester on.

3.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the tester on [A].

6.

Wait for 5 seconds after turning the ignition switch to ON.

7.

Check that 20 seconds or more have elapsed since the ignition switch was turned to ON.

8.

Operate the accelerator pedal in accordance with the following procedure [B].

(a)Enter the following menus: Powertrain / Engine and ECT / Data List / Ptrl Throttle / Accel Sens. No. 1 Volt % and Accel Sens. No.2 Volt %.

(b)Slowly depress the accelerator pedal until Accel Sens. No.1 Volt % is approximately 30% and Accel Sens. No.2 Volt % is approximately 46%, then slowly release the accelerator pedal.

9.

Enter the following menus: Powertrain / Engine and ECT / DTC [C].

10.

Read pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

12.

Input the DTC: P2121.

13.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [B] through [C] again.




FAIL-SAFE

The accelerator pedal sensor assembly has two (main and sub) sensor circuits. If a malfunction occurs in either of the sensor circuits, the ECM detects the abnormal signal voltage difference between the two sensor circuits and switches to fail-safe mode. In fail-safe mode, the functioning circuit is used to calculate the accelerator pedal position to allow the vehicle to continue driving. If both circuits malfunction, the ECM regards the accelerator pedal as being fully released. In this case, the throttle valve remains closed as if the engine is idling.

If a pass condition is detected and then the ignition switch is turned off, the fail-safe operation stops and the system returns to normal.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

HINT:
·

This DTC relates to the accelerator pedal position sensor.

·

Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P2121)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / DTC.


e.

Read DTCs.

Result
Result Proceed to
DTC P2121 is output A
DTC P2121 and other DTCs are output B

HINT:

If any DTCs other than P2121 are output, troubleshoot those DTCs first.




A

2.READ VALUE USING INTELLIGENT TESTER (ACCELERATOR POSITION SENSOR)

B

2.READ VALUE USING INTELLIGENT TESTER (ACCELERATOR POSITION SENSOR)
A160308E03
0.806,1.751 1.044,1.911 0.239,0.161 10 *b 2.395,1.751 2.616,1.911 0.221,0.161 10 *c 1.434,0.233 1.673,0.393 0.239,0.161 10 *a

a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Accel Sensor Out No. 1 and Accel Sensor Out No. 2.


e.

Read the values displayed on the tester.

Standard Voltage:
Accelerator Pedal Operation Accel Sensor Out No. 1 Accel Sensor Out No. 2
Released 0.5 to 1.1 V 1.2 to 2.0 V
Depressed 2.6 to 4.5 V 3.4 to 4.7 V


Text in Illustration
*a Accelerator Pedal Operation
*b Depressed
*c Released



OK

NG

3.REPLACE ACCELERATOR PEDAL SENSOR ASSEMBLY
3.REPLACE ACCELERATOR PEDAL SENSOR ASSEMBLY
a.

Replace the accelerator pedal sensor assembly (See page Engine / Hybrid System>2NZ-FE ENGINE CONTROL>ACCELERATOR PEDAL>REMOVAL).



NEXT

4.CHECK WHETHER DTC OUTPUT RECURS (ACCELERATOR PEDAL POSITION SENSOR DTCS)
4.CHECK WHETHER DTC OUTPUT RECURS (ACCELERATOR PEDAL POSITION SENSOR DTCS)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.



e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON and turn the tester on.


g.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


h.

Enter the following menus: Powertrain / Engine and ECT / DTC.


i.

Read the DTCs.

Result
Result Proceed to
DTC P2121 is output A
DTC is not output B



A

B

END