13201
1.INSPECT CONNECTING ROD THRUST CLEARANCE
Using a dial indicator, measure the thrust clearance while moving the connecting rod back and forth.
0.16 to 0.36 mm (0.0063 to 0.0142 in.)
0.36 mm (0.0142 in.)
13041
2.INSPECT CONNECTING ROD OIL CLEARANCE
Check that the matchmarks on the connecting rod and cap are aligned to ensure correct reassembly.
Using SST, remove the 2 connecting rod cap bolts.
Clean the crank pin and bearing.
Check the crank pin and bearing for pitting and scratches.
Lay a strip of Plastigage across the crank pin.
| *1 | Plastigage |
Make sure that the connecting rod and its cap are in the correct combination and that the front mark on the cap is facing in the correct mounting orientation, then install the cap onto the connecting rod.
| *a | Front Mark |
Apply a light coat of engine oil to the threads of the connecting rod cap bolts.
Using SST, tighten the bolts in several steps to the specified torque.
Mark the front of the connecting cap bolts with paint.
| *a | Paint Mark |
|
Engine Front |
Further tighten the cap bolts by 90° as shown in the illustration.
Do not turn the crankshaft.
Remove the 2 bolts, connecting rod cap and lower bearing.
Measure the Plastigage at its widest point.
| *1 | Plastigage |
0.012 to 0.038 mm (0.00047 to 0.0015 in.)
Completely remove the Plastigage after the measurement.
When replacing a bearing, replace it with one with the same number as marked on the connecting rod. There are 3 sizes of standard bearings, marked 1, 2 and 3 accordingly.
| *a | Mark 1,2 or 3 |
| *b | Front Mark |
| Mark | mm (in.) |
|---|---|
| 1 | 1.491 to 1.494 (0.0587 to 0.0588) |
| 2 | 1.494 to 1.497 (0.0588 to 0.0589) |
| 3 | 1.497 to 1.500 (0.0589 to 0.0591) |
11791
3.INSPECT CRANKSHAFT THRUST CLEARANCE
Using a dial indicator, measure the thrust clearance while moving the crankshaft back and forth with a screwdriver.
0.09 to 0.19 mm (0.0035 to 0.0075 in.)
0.30 mm (0.0118 in.)
If the thrust clearance is greater than the maximum, replace the thrust washers as a set. Check the crankshaft and block for wear. Repair or replace the parts if necessary.
Thrust washer thickness: 2.43 to 2.48 mm (0.0957 to 0.976 in.)
11401
4.INSPECT CYLINDER BLOCK FOR WARPAGE
Using a precision straightedge and feeler gauge, measure the warpage of the surface which is in contact with the cylinder head gasket.
| *1 | Straightedge |
0.05 mm (0.0020 in.)
5.INSPECT CYLINDER BORE
Using a cylinder gauge, measure the cylinder bore diameter at positions A and B in the thrust and axial directions.
| *a | Thrust Direction |
| *b | Axial Direction |
| *c | Center |
|
Engine Front |
75.000 to 75.013 mm (2.9528 to 2.9533 in.)
75.013 mm (2.9533 in.)
Calculate the difference between the maximum diameter and the minimum diameter of the 4 measured values.
0.10 mm (0.0039 in.)
If the difference is greater than the limit, replace the cylinder block.
13101
6.INSPECT WITH PIN PISTON SUB-ASSEMBLY
Using a micrometer, measure the piston diameter at a right angle to the piston pin center line, and at the position 27.6 to 27.8 mm (1.0866 to 1.0945 in.) from top of the piston head.
74.935 to 74.945 mm (2.9502 to 2.9506 in.)
Using a caliper gauge, measure the piston pin hole diameter.
18.013 to 18.016 mm (0.7092 to 0.7093 in.) at 20°C (68°F)
Using a micrometer, measure the piston pin diameter.
18.001 to 18.004 mm (0.7087 to 0.7088 in.)
Subtract the piston pin diameter measurement from the piston pin hole diameter measurement to calculate the oil clearance.
0.009 to 0.015 mm (0.0004 to 0.0006 in.)
0.050 mm (0.0020 in.)
If necessary, replace the piston and piston pin together.
13101
7.INSPECT PISTON CLEARANCE
Subtract the piston diameter measurement from the cylinder bore diameter measurement to calculate the oil clearance.
0.045 to 0.068 mm (0.0018 to 0.0027 in.)
0.08 mm (0.0032 in.)
13011
8.INSPECT RING GROOVE CLEARANCE
Using a feeler gauge, measure the clearance between a new piston ring and the wall of the ring groove.
0.03 to 0.07 mm (0.0012 to 0.0028 in.)
0.02 to 0.06 mm (0.0008 to 0.0024 in.)
0.07 to 0.13 mm (0.0028 to 0.0052 in.)
13011
9.INSPECT PISTON RING END GAP
Using a piston, push the piston ring, a little beyond the bottom of the ring travel, 110 mm (4.33 in.) from the top of the cylinder block.
Using a feeler gauge, measure the end gap.
0.22 to 0.32 mm (0.0086 to 0.0126 in.)
0.32 to 0.47 mm (0.0126 to 0.0185 in.)
0.10 to 0.35 mm (0.0039 to 0.0138 in.)
0.88 mm (0.0346 in.)
1.03 mm (0.0406 in.)
0.82 mm (0.0323 in.)
13265
10.INSPECT CONNECTING ROD BOLT
Using a vernier caliper, measure the diameter of the bolt at the elongated portion.
6.6 to 6.7 mm (0.260 to 0.264 in.)
6.4 mm (0.252 in.)
If the diameter is less than the minimum, replace the bolt.
13411
11.INSPECT CRANKSHAFT
Using a dial indicator and V-blocks, measure the circle runout as shown in the illustration.
0.03 mm (0.0012 in.)
Using a micrometer, measure the diameter of each main journal.
45.988 to 46.000 mm (1.8106 to 1.8110 in.)
Check each main journal for taper and out-of-roundness as shown.
0.02 mm (0.0008 in.)
Using a micrometer, measure the diameter of each crank pin.
39.992 to 40.000 mm (1.5745 to 1.5748 in.)
Check each crank pin for taper and out-of-roundness as shown.
0.02 mm (0.0008 in.)
Wrap the chain around the timing sprocket.
Using a vernier caliper, measure the timing sprocket diameter with the chain.
51.72 mm (2.0362 in.)
50.5 mm (1.988 in.)
Make sure that the vernier caliper is in contact with the chain rollers when measuring.
11416
12.INSPECT CRANKSHAFT BEARING CAP SET BOLT
Using a vernier caliper, measure the tension portion diameter at the elongated portion.
7.3 to 7.5 mm (0.287 to 0.295 in.)
7.2 mm (0.283 in.)
If the diameter is less than minimum, replace the bolt.
11711
13.INSPECT CRANKSHAFT OIL CLEARANCE
Clean each main journal and bearing.
Install the bearing onto the cylinder block and bearing cap. (See page Engine / Hybrid System>2NZ-FE ENGINE MECHANICAL>CYLINDER BLOCK>REASSEMBLY)
Place the crankshaft onto the cylinder block.
Lay a strip of Plastigage across each journal.
| *1 | Plastigage |
Examine the front marks and numbers and install the bearing cap onto the cylinder block.
| *1 | No. 3 Bearing Cap |
| *2 | No. 1,2,4,5 Bearing Cap |
| *a | Front Mark |
| *b | Number |
| *c | Front Mark and Number |
Apply a light coat of engine oil to the threads of the bearing cap bolts.
Using 12 mm socket wrench, tighten the bolts in several steps to the specified torque in the sequence shown in the illustration. (*1)
Mark the front of the bearing cap bolts with paint.
| *a | Paint Mark |
|
Engine Front |
Further tighten the bearing cap bolts by 90° in the same sequence as step (*1).
Check that the painted mark is now at a 90° angle from the front.
Do not turn the crankshaft.
Remove the bearing cap sub-assembly.
Measure the Plastigage at its widest point.
| *1 | Plastigage |
0.01 to 0.023 mm (0.0004 to 0.0009 in.)
0.07 mm (0.0028 in.)
Completely remove the Plastigage after the measurement.
When replacing a standard bearing, replace it with one with the same number. If the number of the bearing cannot be found, select the correct bearing by adding together the numbers imprinted on the cylinder block and crankshaft, then select the bearing with the same number as the total. There are 4 sizes of standard bearings, marked 1, 2, 3 and 4 accordingly.
| *a | Mark |
| Cylinder Block (A)
+ Crankshaft (B) |
0 to 2 | 3 to 5 | 6 to 8 | 9 to 11 |
| Use Bearing | 1 | 2 | 3 | 4 |
| Item | Mark | mm (in.) |
|---|---|---|
| Cylinder block main journal bore diameter (A) | 0
1 2 3 4 5 6 |
50.000 to 50.003 (1.96850 to 1.96862)
50.003 to 50.005 (1.96862 to 1.96870) 50.005 to 50.007 (1.96870 to 1.96878) 50.007 to 50.010 (1.96878 to 1.96890) 50.010 to 50.012 (1.96890 to 1.96898) 50.012 to 50.014 (1.96898 to 1.96906) 50.014 to 50.016 (1.96906 to 1.96913) |
| Crankshaft main journal diameter (B) | 0
1 2 3 4 5 |
45.998 to 46.000 (1.81094 to 1.81102)
45.996 to 45.998 (1.81087 to 1.81094) 45.994 to 45.996 (1.81079 to 1.81087) 45.992 to 45.994 (1.81071 to 1.81079) 45.990 to 45.992 (1.81063 to 1.81071) 45.988 to 45.990 (1.81055 to 1.81063) |
| Standard bearing center wall thickness | 1
2 3 4 |
1.992 to 1.995 (0.07843 to 0.07854)
1.995 to 1.998 (0.07854 to 0.07866) 1.998 to 2.001 (0.07866 to 0.07878) 2.001 to 2.004 (0.07878 to 0.07890) |