Home › Engine / Hybrid System › 2NZ-FE ENGINE MECHANICAL › CAMSHAFT
RM19S0E _51 Engine / Hybrid System _051451 2NZ-FE ENGINE MECHANICAL _0248086 CAMSHAFT A

2NZ-FE ENGINE MECHANICAL  CAMSHAFT  REMOVAL  


PROCEDURE

Hide 51441C 1.REMOVE ENGINE UNDER COVER RH (for Plastic Type)

Hide 51405A 2.REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY (for Metal Type)

Hide 12261 4.DISCONNECT VENTILATION HOSE

Hide 23820 5.DISCONNECT FUEL VAPOR FEED HOSE ASSEMBLY

Hide 11201 7.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 12305 8.REMOVE ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH

Hide 13512 9.REMOVE NO. 2 CAMSHAFT

A116206E08
1.719,0.365 0.865,0.24 true 0.656,0.146 0.854,0.333 0.198,0.188 10 false *a

Text in Illustration
*a Alignment Mark

NOTICE:

When rotating the camshaft with the timing chain removed, rotate the crankshaft damper counterclockwise 40 ° from the TDC and align the timing notch with the alignment mark of the timing chain cover to prevent the pistons from coming into contact with the valves.


a.

Set the No. 1 cylinder to TDC/compression.

i.
A116203E26
2.156,1.063 2.469,1.833 true 2.427,1.844 2.594,2.031 0.167,0.188 10 false *a

Turn the crankshaft damper, and align the timing notch with the timing mark "0" of the oil pump.

Text in Illustration
*a Timing Notch


ii.
A116204E23
1.094,0.719 1.135,1.802 1.135,1.802 2.042,1.521 true 2.219,1.021 1.146,1.792 true 1.01,1.813 1.177,1.979 0.167,0.167 10 false *a

Check that both timing marks on the camshaft timing sprocket and camshaft timing gear are facing upward, as shown in the illustration.

Text in Illustration
*a Timing Mark

HINT:

If not, turn the crankshaft 1 complete revolution (360°) and align the marks as above.




b.
A116207E15
1.094,0.729 1.135,1.781 1.135,1.781 2.031,1.521 true 2.208,1.031 1.146,1.771 true 1.167,0.625 2.479,0.167 2.479,0.167 2.188,0.917 true 1.021,1.802 1.208,1.969 0.188,0.167 10 false *b 2.51,0.021 3.302,0.354 0.792,0.333 10 true *a

Place paint marks on the chain where it touches the timing marks on the camshaft timing sprocket and the camshaft timing gear.

Text in Illustration
*a Paint Mark
*b Timing Mark


c.
G100163

Using an 8 mm (0.31 in.) hexagon wrench, remove the screw plug.


d.
A116209E06
1.74,2.625 1.833,3.01 false 1.76,3.021 1.938,3.188 0.177,0.167 10 false *1

Insert a screwdriver into the service hole in the chain tensioner to pull the stopper plate of the chain tensioner upward.

Text in Illustration
*1 Stopper Plate


e.
A116210E09
1.021,2.479 1.021,2.875 true 0.927,2.906 1.115,3.083 0.188,0.177 10 false *1

Using a wrench, rotate the No. 2 camshaft clockwise to push in the plunger of the chain tensioner.

Text in Illustration
*1 Plunger


f.
A116212

Remove the screwdriver from the service hole, then align the hole the stopper plate with the service hole and insert a 3 mm (0.12 in.) diameter bar into the holes to hold the stopper plate.

HINT:
·

Fix the stopper plate using the bar while rotating the camshaft right and left slightly.

·

Hold the bar with tape so that the bar does not come off.




g.
A116213

Using a wrench, hold the hexagonal lobe of the No. 2 camshaft and remove the flange bolt.


h.
A116214E02
0.896,0.74 0.896,0.448 true 1.229,0.792 1.229,0.458 true 1.667,0.802 1.667,0.458 true 2.094,0.802 2.094,0.458 true 2.531,0.792 2.531,0.458 true 0.854,0.26 1.01,0.438 0.156,0.177 10 false 1 2.5,0.26 2.656,0.438 0.156,0.177 10 false 2 1.198,0.26 1.354,0.438 0.156,0.177 10 false 3 2.063,0.26 2.219,0.438 0.156,0.177 10 false 4 1.635,0.26 1.792,0.438 0.156,0.177 10 false 5

Using several steps, loosen and remove the 11 bearing cap bolts uniformly in the sequence shown in the illustration, then remove the No. 1 and No. 2 camshaft bearing caps.

NOTICE:

Loosen the bolts uniformly while keeping the camshaft level.



i.
A116215

Remove the flange bolt and the camshaft timing sprocket.


j.
A116216

Remove the No. 2 camshaft.


Hide 13511 10.REMOVE CAMSHAFT

a.
A116217E03
1.135,1.302 1.135,1.51 true 1.604,1.313 1.604,1.51 true 2.083,1.313 2.083,1.5 true 2.563,1.302 2.563,1.49 true 1.094,1.531 1.25,1.708 0.156,0.177 10 false 2 1.563,1.542 1.719,1.719 0.156,0.177 10 false 4 2.052,1.531 2.208,1.708 0.156,0.177 10 false 3 2.531,1.521 2.688,1.698 0.156,0.177 10 false 1

Using several steps, loosen and remove the 8 bearing cap bolts uniformly in the sequence shown in the illustration, then remove the No. 2 camshaft bearing cap.

NOTICE:

Loosen each bolt uniformly while keeping the camshaft level.



b.
A116218

Hold the chain by hand, and remove the camshaft and the camshaft timing gear assembly.


c.
A035227

Tie the chain with a piece of string as shown in the illustration.


Hide 13050 11.REMOVE CAMSHAFT TIMING GEAR ASSEMBLY

a.

Clamp the camshaft in a vise and confirm that it is locked.

NOTICE:

Do not damage the camshaft.



b.
A116226E22
1.323,2.948 0.802,3.292 true 1.969,3.01 2.656,2.813 true 1.396,3.25 0.875,3.625 true 1.365,3.448 0.813,3.885 true 2.01,3.271 2.594,3.875 true 1.885,3.208 2.479,3.313 true 1.563,0.99 0.948,0.25 0.948,0.25 1.865,0.979 true 1.583,1.135 2.156,1.531 2.156,1.531 1.865,1.125 true 2.635,3.854 2.802,4.021 0.167,0.167 10 false *1 0.635,3.844 0.802,4.01 0.167,0.167 10 false *2 2.198,1.469 2.365,1.635 0.167,0.167 10 false *a 0.75,0.146 0.917,0.313 0.167,0.167 10 false *b 2.688,2.698 2.854,2.865 0.167,0.167 10 false *c 2.521,3.229 2.688,3.396 0.167,0.167 10 false *d 0.667,3.573 0.833,3.74 0.167,0.167 10 false *c 0.635,3.24 0.802,3.406 0.167,0.167 10 false *d

Cover the 4 oil paths of the cam journal with tape as shown in the illustration.

Text in Illustration
*1 Rubber Piece
*2 Vinyl Tape
*a Advance Side Path
*b Retard Side Path
*c Open
*d Close

HINT:

One of the 2 grooves located on the cam journal is for retarding cam timing (upper) and the other is for advancing cam timing (lower). Each groove has 2 oil paths. Plug one of the oil paths for each groove with a piece of rubber before wrapping the cam journal with the tape.



c.

Puncture the tape covering the advance oil path and the retard oil path on the opposite side from the advance oil path.


d.
A116227E07
1.604,0.875 0.875,0.344 true 1.833,0.948 2.583,0.323 true 2.615,0.219 2.792,0.385 0.177,0.167 10 false *a 0.677,0.25 0.854,0.417 0.177,0.167 10 false *b

Apply air at about 150 kPa (1.5 kgf/cm2) pressure into the 2 broken paths (the advance side path and the retard side path).

Text in Illustration
*a Advance Side Path
*b Retard Side Path

NOTICE:

Cover the paths with a piece of cloth to prevent oil splashes.



e.
A116228E11
1.865,1.667 2.5,0.854 true 1.625,1.594 0.854,0.854 true 0.646,0.74 0.823,0.927 0.177,0.188 10 false *b 2.531,0.719 2.708,0.906 0.177,0.188 10 false *a 0.49,2.625 0.698,2.792 0.208,0.167 10 false *d 2.771,2.625 2.979,2.792 0.208,0.167 10 false *c

Confirm that the camshaft timing gear assembly revolves in the timing advance direction when the air pressure on the timing retard path is reduced.

Text in Illustration
*a Advance Side Path
*b Retard Side Path
*c Hold Pressure
*d Decompress

HINT:

The lock pin is released, and the camshaft timing gear revolves in the advance direction.



f.

When the camshaft timing gear reaches the most advanced position, release the air pressure on the timing retard side path, and then release the air pressure on the timing advance side path.

NOTICE:

The camshaft timing gear assembly occasionally shifts to the retard side abruptly, if the air pressure on the advance side path is released first. This often results in the breakage of the lock pin.



g.
A116229

Remove the flange bolt and the camshaft timing gear assembly.

NOTICE:
·

Do not remove the other 4 bolts.

·

When reusing the camshaft timing gear, unlock the lock pin inside the camshaft timing gear first.