Home › Engine / Hybrid System › 2NZ-FE FUEL › FUEL INJECTOR › 2011.08–2016.09
RM19S0E _51 Engine / Hybrid System _051452 2NZ-FE FUEL _0248091 FUEL INJECTOR A

2NZ-FE FUEL  FUEL INJECTOR  INSTALLATION  


PROCEDURE

Hide 23250 1.INSTALL FUEL INJECTOR ASSEMBLY

A115499E04
1.761,1.795 2.23,1.466 false 1.556,1.732 1.734,1.911 0.178,0.179 10 *1

Text in Illustration
*1 O-ring

a.

Apply a light coat of gasoline or spindle oil to new O-rings, then install one onto each fuel injector.


b.

Apply a light coat of gasoline or spindle oil to the contact surfaces of the fuel delivery pipe and the O-ring of the fuel injector.


c.
A260536

While turning the fuel injector left and right, install it onto the fuel delivery pipe.

Text in Illustration
V100135

Push
V100136

Turn

NOTICE:
·

Do not twist the O-ring.

·

After installing the fuel injectors, check that they turn smoothly. If not, replace the O-ring with a new one.




Hide 23291 2.INSTALL INJECTOR VIBRATION INSULATOR

a.

Install the 4 new injector vibration insulators onto the cylinder head.


Hide 23807V 3.INSTALL NO. 1 DELIVERY PIPE SPACER

a.

Install the 2 No. 1 delivery pipe spacers onto the cylinder head.

NOTICE:

Install the delivery pipe No. 1 spacer in the correct direction.



Hide 23807 4.INSTALL FUEL DELIVERY PIPE SUB-ASSEMBLY

A115494E09
0.75,0.229 0.906,0.406 0.156,0.177 10 true A 1.469,0.76 1.625,0.938 0.156,0.177 10 true A 2.906,1.781 3.063,1.958 0.156,0.177 10 false B

a.

Install the fuel delivery pipe sub-assembly with the 4 fuel injectors, then provisionally install the 3 bolts.

NOTICE:
·

Do not drop the fuel injectors when installing the fuel delivery pipe sub-assembly.

·

Check that the fuel injectors rotate smoothly after installing the fuel delivery pipe subassembly.




b.

Tighten the 3 bolts to the specified torque.

Torque:
Bolt A : 19 N*m (194 kgf*cm, 14 ft.*lbf)
Bolt B : 9.0 N*m (92 kgf*cm, 80 in.*lbf)


Hide 23901 5.CONNECT FUEL TUBE SUB-ASSEMBLY

A154755

Text in Illustration
V100135

Push

a.

Insert the fuel tube connector into the fuel delivery pipe until a click sound can be heard.

NOTICE:
·

Check that there are no scratches or foreign matter around the disconnected parts of the fuel tube connector and pipe before performing this work.

·

After connecting the fuel tube, check that the fuel tube connector and pipe are securely connected by pulling them.




b.

Install the fuel pipe clamp.


Hide 11201 6.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY

A260538

Text in Illustration
V100155

Seal Packing

a.

Apply seal packing to the cylinder head as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


NOTICE:
·

Remove any oil from the contact surfaces.

·

Install the cylinder head cover within 3 minutes and tighten the bolts within 15 minutes after applying seal packing.

·

Do not start the engine for at least 2 hours after the installation.




b.
A382055E01
0.302,0.104 0.615,0.302 0.313,0.198 10 false 11 0.906,0.125 1.063,0.323 0.156,0.198 10 false 9 1.948,0.125 2.104,0.323 0.156,0.198 10 false 5 3.031,0.156 3.188,0.354 0.156,0.198 10 false 7 0.271,1.021 0.51,1.188 0.24,0.167 10 true 10 1.281,1.042 1.438,1.24 0.156,0.198 10 false 1 2.469,1.042 2.625,1.24 0.156,0.198 10 false 2 0.375,1.813 0.531,2.01 0.156,0.198 10 false 8 0.885,1.656 1.042,1.854 0.156,0.198 10 false 3 1.906,1.698 2.063,1.896 0.156,0.198 10 false 6 3.021,1.677 3.177,1.875 0.156,0.198 10 false 4

Install the cylinder head cover sub-assembly with the 9 bolts, 2 nuts and 2 seal washers.


c.

Tighten the 9 bolts and 2 nuts in the sequence shown in the illustration.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


d.

for LHD:

i.

Connect the connector and 4 wire harness clamps and connect the engine wire harness.


ii.

Install the wire harness bracket with the bolt.

Torque:
13 N*m (130 kgf*cm, 9 ft.*lbf)



e.

for RHD:

i.

Connect the connector and 3 wire harness clamps and connect the engine wire harness.



f.

Connect the 4 fuel injector connectors.


Hide 23820 8.CONNECT FUEL VAPOR FEED HOSE ASSEMBLY

a.

Connect fuel vapor feed hose assembly.


Hide 12261 9.CONNECT VENTILATION HOSE

a.

Connect the ventilation hose.


Hide 11.INSPECT FOR ENGINE OIL LEAK