Home › Engine / Hybrid System › 1NZ-FE FUEL › FUEL TANK
RM19S0E _51 Engine / Hybrid System _051453 1NZ-FE FUEL _0248099 FUEL TANK A

1NZ-FE FUEL  FUEL TANK  REMOVAL  


PROCEDURE

Hide 1. PRECAUTION

a.
A250068E01
1.904,0.751 2.212,0.304 false 2.236,0.188 2.432,0.361 0.196,0.174 10 *1

When removing and storing the fuel tank assembly, arrange the inlet hose as shown in the illustration, and secure the fuel tank assembly using a cord or similar.

Text in Illustration
*1 Cord

NOTICE:

Depending on the arrangement of the inlet hose during storage, the inlet hose and rear suspension may interfere and cause fuel leakage.



Hide 77020A 2.REMOVE FUEL SUCTION TUBE ASSEMBLY WITH PUMP AND GAUGE

Hide 3.DRAIN FUEL

Hide 58153 4.REMOVE FRONT NO. 2 FLOOR HEAT INSULATOR

a.
A247502

Remove the 2 nuts and the front No. 2 floor heat insulator.


Hide 77606F 5.REMOVE FUEL TANK COVER VENT CASE SUB-ASSEMBLY

a.
A247503

Remove the clip.


b.

Remove the bolt and fuel tank cover vent case sub-assembly.


Hide 77209D 6.DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY

NOTICE:

Before disconnecting the fuel tube connector, check for dirt or other foreign matter on the fuel tube connector and the pipe, and clean them if necessary.


a.
A259223E01
2.236,4.157 2.612,4.059 false 2.625,3.944 2.778,4.089 0.153,0.146 10 *1 1.891,2.464 2.044,2.609 0.153,0.146 10 *1 0.648,3.908 0.801,4.053 0.153,0.146 10 *2 1.604,3.501 1.757,3.647 0.153,0.146 10 *3 2.053,3.501 2.205,3.647 0.153,0.146 10 *4 0.833,3.996 1.092,4.082 false 1.624,3.937 1.696,3.679 1.696,3.679 1.764,3.932 false 2.035,3.875 2.134,3.661 false 1.359,1.82 1.511,1.966 0.153,0.146 10 *4 2.076,2.53 2.339,2.324 false 0.931,2.133 1.358,1.95 false

Disengage the fuel tube connector cover.

Text in Illustration
*1 Checker
*2 Fuel Tube Connector
*3 O-ring
*4 Retainer
V100135

Pinch
V100136

Pull


b.

Pinch the retainer by hand from both sides, and pull out the fuel tube connector from the pipe.

NOTICE:
·

If the fuel tube connector and pipe are stuck together, push in and pull out the fuel tube connector while squeezing the pipe to release the connection, and then disconnect the fuel tube connector.

·

Clean away any dirt or foreign matter from the fuel tube connector before performing the operation.

·

The fuel tube connector and pipe are sealed by O-rings, so be careful to prevent damage to and foreign matter sticking to the contact surfaces.

·

Do not use any tools.

·

After disconnecting the fuel tube connector, check that there is no foreign matter on the seal surface of the pipe.

·

After disconnecting the fuel tube, protect the contact surfaces by covering them with a plastic bag.

·

Do not bend or twist the tubes.




Hide 77262 7.DISCONNECT NO. 2 FUEL EMISSION TUBE

NOTICE:

Before disconnecting the fuel tube connector, check for dirt or other foreign matter on the fuel tube connector and the pipe, and clean them if necessary.


a.
A210933E02
2.161,2.833 2.325,2.993 0.164,0.160 10 *1 0.817,2.933 1.012,3.093 0.195,0.160 10 *2 1.522,4.219 1.699,4.380 0.177,0.160 10 *4 0.343,4.14 0.524,4.300 0.182,0.160 10 *3 1.622,0.806 1.803,0.974 0.181,0.168 10 *a 1.692,1.892 1.895,2.052 0.204,0.160 10 *b 2.391,2.939 2.7,3.55 false 1.059,3.038 1.557,3.558 false 0.47,4.099 0.838,3.732 false 1.077,4.03 1.471,4.292 false

Loosen the clamp and disconnect the No. 2 fuel emission tube.

Text in Illustration
*1 Rubber Hose
*2 O-ring
*3 Fuel Pipe
*4 Retainer
*a Pull Back
*b Pull Out

NOTICE:
·

If the fuel tube connector and pipe are stuck together, push in and pull out the fuel tube connector while squeezing the pipe to release the connection, and then disconnect the fuel tube connector.

·

Clean away any dirt or foreign matter from the fuel tube connector before performing the operation.

·

The fuel tube connector and pipe are sealed by O-ring, so be careful to prevent damage to and foreign matter sticking to the contact surfaces.

·

Do not use any tools.

·

After disconnecting the fuel tube connector, check that there is no foreign matter on the seal surface of the pipe.

·

After disconnecting the fuel tube, protect the contact surfaces by covering them with a plastic bag.

·

Do not bend or twist the tubes.




Hide 77100 8.REMOVE FUEL TANK ASSEMBLY

A247506

a.

Remove the bolt.


b.

Disengage the clip as shown in the illustration and remove the fuel tank filler pipe flange plate.


c.

Using an engine lifter, support the fuel tank assembly.


d.
A247508

Separate the 2 fuel hoses shown in the illustration.


e.
A261048

Remove the 4 bolts and fuel tank assembly.

NOTICE:

Make sure that the fuel tank does not fall.



Hide 77209D 9.REMOVE FUEL TANK MAIN TUBE SUB-ASSEMBLY

a.
A247511

Disengage the clamp and remove the fuel tank main tube from the fuel tank assembly.


Hide 77262 10.REMOVE NO. 2 FUEL EMISSION TUBE

a.
A247512

Disengage the clamp and remove the No. 2 fuel emission tube from the fuel tank assembly.


Hide 77701W 11.REMOVE NO. 1 CANISTER OUTLET HOSE SUB-ASSEMBLY

a.
A247513

Remove the No. 1 canister outlet hose from the fuel tank assembly.


Hide 23841H 12.REMOVE FUEL HOSE CLAMP

a.
A247514

Remove the fuel hose clamp.


Hide 77217C 13.REMOVE NO. 2 FUEL TANK FILLER PIPE SUPPORT

a.
A247531

Disengage the clamp as shown in the illustration, and remove the No. 2 fuel tank filler pipe support.


Hide 77216A 14.REMOVE NO. 1 FUEL TANK FILLER PIPE SUPPORT

A247533

a.

Disengage the clamp as shown in the illustration, and remove the No. 1 fuel tank filler pipe support.


Hide 77218A 15.REMOVE NO. 3 FUEL TANK FILLER PIPE SUPPORT

a.
A247529

Disengage the clamp as shown in the illustration, and remove the No. 3 fuel tank filler pipe support.