Home › Engine / Hybrid System › 2NZ-FE INTAKE / EXHAUST › EXHAUST PIPE › 2011.08–2014.07
RM19S0E _51 Engine / Hybrid System _051457 2NZ-FE INTAKE / EXHAUST _0248117 EXHAUST PIPE A

2NZ-FE INTAKE / EXHAUST  EXHAUST PIPE  INSTALLATION  


PROCEDURE

Hide 17408 1.INSTALL EXHAUST TAIL PIPE BAFFLE SUB ASSEMBLY (w/ Side Mudguard)

a.
A173892E02
2.156,1.385 2.479,1.698 false 2.573,0.313 1.917,0.219 true 2.771,0.396 2.75,0.667 false 2.51,1.698 2.719,1.875 0.208,0.177 10 false *1 1.74,0.125 1.938,0.313 0.198,0.188 10 false *a 2.646,0.688 2.802,0.833 0.156,0.146 10 false *b

Align the keyway on a new tail exhaust pipe baffle sub-assembly with the protruding part of the exhaust tail pipe as shown in the illustration.

Text in Illustration
*1 Plastic Hammer
*a Protruding Part
*b Keyway


b.

Using a plastic hammer, uniformly tap in the tail exhaust pipe baffle sub-assembly.


Hide 17410 3.INSTALL FRONT EXHAUST PIPE ASSEMBLY

a.
A128853

Using a vernier caliper, measure the free length of the compression springs.

Minimum length:

41.5 mm (1.634 in.)


If the length is not as specified, replace the compression spring.


b.

Hang the front exhaust pipe assembly with the 3 exhaust pipe supports.


c.
A247549E04
0.271,0.521 0.542,0.667 false 0.281,0.958 0.531,0.896 false 1.958,0.979 2.125,1.229 true 0.115,0.438 0.281,0.656 0.167,0.219 10 false *1 0.115,0.896 0.281,1.104 0.167,0.208 10 false *2 2.063,1.24 2.219,1.438 0.156,0.198 10 false *3 2.75,1.344 2.958,1.594 0.208,0.25 10 false *a

Install the front exhaust pipe sub-assembly onto the exhaust manifold converter sub-assembly with the 2 compression springs and 2 bolts.

Text in Illustration
*1 Exhaust Manifold
*2 Front Exhaust Pipe Assembly
*3 Gasket
*a Space between flanges: 8.5 mm (0.335 in.)

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)

HINT:

After the installation, check that the gaps between the flanges of the exhaust manifold converter sub-assembly and front exhaust pipe assembly are consistent front-to-rear and left-to-right.



Hide 17430 5.INSTALL TAIL EXHAUST PIPE ASSEMBLY

a.
A128853

Using a vernier caliper, measure the free length of the compression springs.

Minimum length:

38.5 mm (1.516 in.)


If the length is not as specified, replace the compression spring.


b.

Hang the front exhaust pipe assembly with the 2 exhaust pipe supports.


c.
A247551E04
2.635,1.104 2.948,1.063 false 2.625,1.333 2.917,1.396 false 1.458,1.365 1.375,1.594 false 0.469,0.625 0.625,0.771 0.156,0.146 10 false *a 2.979,0.958 3.156,1.167 0.177,0.208 10 false *1 2.958,1.333 3.146,1.531 0.188,0.198 10 false *2 1.25,1.594 1.406,1.74 0.156,0.146 10 false *3

Install the tail exhaust pipe assembly onto the front exhaust pipe assembly with the 2 compression springs and 2 bolts.

Text in Illustration
*1 Front Exhaust pipe Assembly
*2 Tail Exhaust Pipe Assembly
*3 Gasket
*a Space between flanges: 6.5 mm (0.256 in.)

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)

HINT:

After the installation, check that the gaps between the flanges of the exhaust manifold converter sub-assembly and front exhaust pipe assembly are consistent front-to-rear and left-to-right.



Hide 57533B 6.INSTALL FRONT FLOOR CENTER BRACE (w/ Side Mudguard)

Hide 89465A 7.INSTALL NO. 2 OXYGEN SENSOR (for Sensor 2)

Hide 8.INSPECT FOR EXHAUST GAS LEAK