Home › Drivetrain › U340E (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSAXLE SYSTEM › 2011.08–2016.09
RM19S0E _52 Drivetrain _051465 U340E AUTOMATIC TRANSMISSION / TRANSAXLE _0248156 AUTOMATIC TRANSAXLE SYSTEM C

U340E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  P0787  Shift / Timing Solenoid Low (Shift Solenoid Valve ST)  P0788  Shift / Timing Solenoid High (Shift Solenoid Valve ST)  


DESCRIPTION

Shift solenoid valve ST is switched OFF-ON-OFF in accordance with signals from the ECM when up-shifting and down-shifting between the 3rd and the 4th gears. This reduces the shock of gear shifting between these positions.

DTC No. DTC Detection Condition Trouble Area
P0787 ECM detects short in solenoid valve ST circuit 4 times when solenoid valve ST is operated (1 trip detection logic).
·

Wire harness or connector

·

Transmission wire

·

Shift solenoid valve ST

·

ECM


P0788 ECM detects open in solenoid valve ST circuit 4 times when solenoid valve ST is not operated (1 trip detection logic).
·

Wire harness or connector

·

Transmission wire

·

Shift solenoid valve ST

·

ECM



MONITOR DESCRIPTION

When there is an open or short circuit in the shift solenoid valve circuit, the ECM detects the problem and the MIL comes on.

WIRING DIAGRAM

C243326E01
0.979,1.959 1.279,2.099 0.300,0.140 10 B74 0.979,2.118 2.165,2.296 1.186,0.178 10 Transmission Wire 6.024,2.177 6.374,2.342 0.350,0.165 10 ECM 5.837,1.092 6.039,1.253 0.202,0.161 10 ST 5.466,1.09 5.752,1.255 0.286,0.165 10 B84 5.522,0.9 5.697,1.054 0.175,0.154 10 80 2.296,1.214 2.497,1.374 0.201,0.159 10 ST 2.615,0.992 2.712,1.148 0.097,0.156 10 2 1.148,1.329 2.041,1.639 0.894,0.310 10 Shift Solenoid Valve ST

PROCEDURE

1.INSPECT TRANSMISSION WIRE (SHIFT SOLENOID VALVE ST)
C229166E13
2.716,0.714 3.115,0.872 0.398,0.158 10 ST 1.998,0.931 2.676,0.803 false 0.059,0.059 0.256,0.223 0.197,0.164 10 *a

a.

Disconnect the transmission wire connector from the transaxle.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (ST) - Body ground 20°C (68°F) 11 to 15 Ω


Text in Illustration
*a Component without harness connected
(Transmission Wire)



OK

2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)

NG

3.INSPECT SHIFT SOLENOID VALVE ST
2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)
U158334E01
1.482,0.254 1.785,0.421 0.303,0.167 10 B84 0.048,0.027 0.258,0.210 0.210,0.182 10 *a 1.812,1.798 2.031,1.948 0.220,0.150 10 ST 2.001,1.235 1.938,1.77 false

a.

Connect the transmission wire connector to the transaxle.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B84-80 (ST) - Body ground 20°C (68°F) 11 to 15 Ω


Text in Illustration
*a Front view of wire harness connector
(to ECM)



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT SHIFT SOLENOID VALVE ST
C355232E01
0.542,3.021 0.729,3.198 0.188,0.177 10 false (+) 0.573,3.667 0.76,3.844 0.188,0.177 10 false (-)

a.

Remove shift solenoid valve ST.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - Solenoid Body 20°C (68°F) 11 to 15 Ω



c.

Connect the positive (+) lead to the terminal of the solenoid connector and the negative (-) lead to the solenoid body to check the solenoid valve operation.

OK:

The solenoid makes operating sounds.


Text in Illustration
*a Component without harness connected
(Shift Solenoid Valve ST)



OK

NG