Home › Drivetrain › U340E (AUTOMATIC TRANSMISSION / TRANSAXLE) › DIFFERENTIAL CASE
RM19S0E _52 Drivetrain _051465 U340E AUTOMATIC TRANSMISSION / TRANSAXLE _0248169 DIFFERENTIAL CASE A

U340E AUTOMATIC TRANSMISSION / TRANSAXLE  DIFFERENTIAL CASE  REASSEMBLY  


PROCEDURE

Hide 41039A 1.INSTALL DIFFERENTIAL GEAR KIT

a.
C081320

After applying Toyota Genuine ATF WS to the differential gear kit (2 front differential pinions and 2 front differential side gears), 2 front differential side gear thrust washers and the 2 front differential pinion thrust washers, and install them to the front differential case.

HINT:

When installing them, set the alignment of the front differential pinions perpendicular to that of the front differential side gear and rotate them so that their holes are aligned with the holes in the differential case.



Hide 41342F 2.INSTALL FRONT NO. 1 DIFFERENTIAL PINION SHAFT

a.
C081321

Install the front No. 1 differential pinion shaft so as to align the straight pin holes in the front No. 1 differential pinion shaft and the differential case.


Hide 41342A 4.INSTALL FRONT DIFFERENTIAL PINION SHAFT STRAIGHT PIN

a.
C081323

Using a pin punch 5 mm and hammer, install the front differential pinion shaft straight pin to the differential case.


b.
C081324

Using a chisel and hammer, stake the differential case hole.


Hide 41221 5.INSTALL FRONT DIFFERENTIAL RING GEAR

D025177

a.

Using ATF and a heater, heat the front differential ring gear to 90 to 110°C (194 to 230°F).

CAUTION:

Use thick gloves to protect your hands as the front differential ring gear is hot.



b.

Clean the contact surface of the differential case and the front differential ring gear.


c.
D025172E11
1.823,1.458 2.677,1.479 false 1.823,1.531 2.677,1.479 false 2.698,1.385 2.865,1.542 0.167,0.156 10 false *a

After moisture on the front differential ring gear has completely evaporated, align the matchmarks on the front differential ring gear and the differential case, and quickly install them.

Text in Illustration
*a Matchmark


d.
U134460

Install 4 new ring gear lock plates with the 8 bolts.

Torque:
88 N*m (898 kgf*cm, 65 ft.*lbf)


e.
C355367E01
0.969,0.615 1.521,0.406 false 1.615,0.271 1.938,0.448 0.323,0.177 10 false SST

Using SST and a hammer, stake the 4 ring gear lock plates.

SST
09930-00010  


Hide 41311F 6.INSTALL FRONT DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING

a.
C355368E01
1.75,0.5 2.469,0.5 2.469,0.5 1.917,0.938 false 2.552,0.417 2.875,0.604 0.323,0.188 10 false SST

Using SST and a press, install the front differential case rear tapered roller bearing inner race to the differential case.

SST
09726-40010  
09950-60020  (09951-00790)


b.
C355369E01
1.417,0.875 1.042,0.344 1.042,0.344 1.5,0.656 false 1.594,1.542 2.219,1.854 2.219,1.854 2.427,1.302 false 0.729,0.25 1.021,0.427 0.292,0.177 10 false SST 2.167,1.906 2.458,2.083 0.292,0.177 10 false SST

Using SST and a press, install the front differential rear case shim and the front differential case rear tapered roller bearing outer race to the transaxle case.

SST
09950-60020  (09951-00720)
09950-60010  (09951-00650)
09950-70010  (09951-07100, 09951-07200)


Hide 41311E 7.INSTALL FRONT DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING

a.
C162532E01
2.43,0.306 2.739,0.474 0.309,0.167 10 SST 1.726,0.496 2.395,0.411 2.395,0.411 1.801,0.72 false

Using SST and a press, install the front differential case front tapered roller bearing inner race to the differential case.

SST
09950-60010  (09951-00460)
09950-70010  (09951-07100)


b.
C355370E01
1.521,1.396 2.635,0.667 2.635,0.667 1.698,1.76 false 2.698,0.552 3.01,0.719 0.313,0.167 10 false SST

Using SST and a press, install the front differential case front tapered roller bearing outer race to the transaxle housing.

SST
09950-70010  (09951-07150)
09950-60020  (09951-00680)