Home › Drivetrain › U441E (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSAXLE SYSTEM › 2011.08–2014.07
RM19S0E _52 Drivetrain _051466 U441E AUTOMATIC TRANSMISSION / TRANSAXLE _0248170 AUTOMATIC TRANSAXLE SYSTEM C

U441E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  P0705  Transmission Range Sensor Circuit Malfunction (PRNDL Input)  


DESCRIPTION

The park/neutral position switch detects the shift lever position and sends signals to the ECM.

DTC No. DTC Detection Condition Trouble Area
P0705 One of the following conditions (A), (B) or (C) is met:
·

Wire harness or connector

·

Park/neutral position switch assembly

·

Shift lock control unit assembly (Transmission control switch)

·

ECM


Condition (A):
Any 2 or more of the following signals are ON simultaneously (2 trip detection logic).
·

One of the following conditions is met.

P input signal is ON.

N input signal is ON.

NSW input signal is ON.

·

R input signal is ON.

·

D input signal is ON.

·

2 input signal is ON.

·

L input signal is ON.


Condition (B):
All switches are OFF simultaneously (2 trip detection logic).
·

P input signal is OFF.

·

N input signal is OFF.

·

NSW input signal is OFF.

·

R input signal is OFF.

·

D input signal is OFF.

·

2 input signal is OFF.

·

L input signal is OFF.


Condition (C):
When any of following conditions is met, the 3 position input signal is ON for 2 seconds or more (2 trip detection logic).
·

NSW input signal is ON.

·

P input signal is ON.

·

R input signal is ON.

·

N input signal is ON.

·

2 input signal is ON.

·

L input signal is ON.



MONITOR DESCRIPTION

This DTC indicates a problem with the park/neutral position switch and the wire harness in the park/neutral position switch circuit.

The park/neutral position switch detects the shift lever position and sends a signal to the ECM.

For safety, the park/neutral position switch detects the shift lever position so that the engine can be started only when the shift lever is in P or N.

The park/neutral position switch sends a signal to the ECM according to the shift position (P, R, N, D, 2 or L). The ECM determines that there is a problem with the switch or related parts if it receives 2 or more position signals simultaneously or it receives no position signal. The ECM turns on the MIL and stores the DTC.

WIRING DIAGRAM

C243249E02
0.184,0.648 0.958,0.791 0.774,0.142 10 to ST Relay 0.456,2.284 0.993,2.439 0.537,0.155 10 GAUGE 1.573,0.581 1.678,0.726 0.105,0.145 10 5 1.755,0.761 1.860,0.906 0.105,0.145 10 L 2.931,0.581 3.036,0.726 0.105,0.145 10 4 2.751,0.761 2.869,0.906 0.118,0.145 10 B 2.931,1.141 3.036,1.286 0.105,0.145 10 6 2.663,1.322 2.868,1.467 0.205,0.145 10 PL 2.931,1.505 3.036,1.650 0.105,0.145 10 1 2.663,1.686 2.868,1.831 0.205,0.145 10 RL 2.931,1.884 3.036,2.029 0.105,0.145 10 9 2.663,2.064 2.868,2.209 0.205,0.145 10 NL 2.931,2.262 3.036,2.407 0.105,0.145 10 7 2.663,2.442 2.868,2.588 0.205,0.145 10 DL 2.931,2.64 3.036,2.786 0.105,0.145 10 3 2.663,2.821 2.868,2.966 0.205,0.145 10 2L 2.931,3.005 3.036,3.150 0.105,0.145 10 8 2.663,3.185 2.868,3.331 0.205,0.145 10 LL 1.09,3.269 1.369,3.421 0.279,0.152 10 B69 1.09,3.417 3.543,3.577 2.452,0.160 10 Park/Neutral Position Switch Assembly 1.573,2.079 1.678,2.224 0.105,0.145 10 2 1.74,2.26 2.019,2.405 0.278,0.145 10 RB 1.566,4.303 1.667,4.467 0.101,0.164 10 1 1.745,4.526 2.155,4.676 0.410,0.150 10 NSSD 2.925,4.303 3.026,4.467 0.101,0.164 10 2 2.598,4.526 2.871,4.676 0.273,0.150 10 AT3 1.232,4.676 1.628,4.829 0.397,0.153 10 F25 1.232,4.846 3.273,5.163 2.042,0.317 10 Shift Lock Control Unit Assembly (Transmission Control Switch) 5.425,0.656 5.705,0.805 0.280,0.148 10 B84 5.479,0.475 5.661,0.614 0.182,0.139 10 52 5.773,0.656 6.141,0.805 0.367,0.148 10 NSW 5.425,1.203 5.705,1.351 0.280,0.148 10 B84 5.479,1.021 5.661,1.160 0.182,0.139 10 73 5.773,1.203 6.141,1.351 0.367,0.148 10 P 5.425,1.595 5.705,1.744 0.280,0.148 10 B84 5.479,1.414 5.661,1.552 0.182,0.139 10 53 5.773,1.595 6.141,1.744 0.367,0.148 10 R 5.425,1.973 5.705,2.122 0.280,0.148 10 B84 5.479,1.792 5.661,1.930 0.182,0.139 10 54 5.773,1.973 6.141,2.122 0.367,0.148 10 N 5.425,2.338 5.705,2.486 0.280,0.148 10 B84 5.479,2.156 5.661,2.295 0.182,0.139 10 56 5.479,2.548 5.661,2.687 0.182,0.139 10 55 5.479,2.927 5.661,3.065 0.182,0.139 10 74 5.773,2.338 6.141,2.486 0.367,0.148 10 D 5.425,2.73 5.705,2.878 0.280,0.148 10 B84 5.773,2.73 6.141,2.878 0.367,0.148 10 2 5.425,3.108 5.705,3.257 0.280,0.148 10 B84 5.773,3.108 6.141,3.257 0.367,0.148 10 L 5.479,4.216 5.661,4.354 0.182,0.139 10 26 5.425,4.397 5.705,4.546 0.280,0.148 10 A74 5.773,4.397 6.141,4.546 0.367,0.148 10 3 6.127,4.847 6.505,5.017 0.378,0.170 10 ECM

CAUTION / NOTICE / HINT

DATA LIST


HINT:

Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Turn the ignition switch off.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the intelligent tester on.


e.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data.


f.

In accordance with the display on the tester, read the Data List.



Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Neutral Position SW Signal PNP switch Status/
OFF or ON
·

OFF: Shift lever not in P and N

·

ON: Shift lever in P or N


When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect.
Shift SW Status (R Range) PNP switch Status/
OFF or ON
·

OFF: Shift lever not in R

·

ON: Shift lever in R


Shift SW Status (P Range) PNP switch Status/
OFF or ON
·

OFF: Shift lever not in P

·

ON: Shift lever in P


Shift SW Status (N Range) PNP switch Status/
OFF or ON
·

OFF: Shift lever not in N

·

ON: Shift lever in N


Shift SW Status (D Range) PNP switch Status/
OFF or ON
·

OFF: Shift lever not in D

·

ON: Shift lever in D


Shift SW Status (3 Range) PNP switch Status/
OFF or ON
·

OFF: Shift lever not in 3

·

ON: Shift lever in 3


Shift SW Status (2 Range) PNP switch Status/
OFF or ON
·

OFF: Shift lever not in 2

·

ON: Shift lever in 2


Shift SW Status (L Range) PNP switch Status/
OFF or ON
·

OFF: Shift lever not in L

·

ON: Shift lever in L



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (POWER SOURCE OF PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
a.
U158307E01
0.152,0.064 0.346,0.248 0.194,0.184 10 *a 3.054,0.487 3.276,0.649 0.222,0.162 10 RB 3.013,0.562 2.891,0.562 2.891,0.562 1.921,1.059 false 0.245,1.049 0.534,1.204 0.290,0.156 10 B69

Disconnect the park/neutral position switch assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B69-2 (RB) - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Park/Neutral Position Switch Assembly)



OK

2.CHECK HARNESS AND CONNECTOR (NSW TERMINAL VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (NSW TERMINAL VOLTAGE)
a.
U158308E01
0.152,0.064 0.346,0.248 0.194,0.184 10 *a 3.054,0.487 3.276,0.649 0.222,0.162 10 B 3.013,0.562 2.891,0.562 2.891,0.562 2.29,1.059 false 0.245,1.049 0.534,1.204 0.290,0.156 10 B69

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B69-4 (B) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V


Text in Illustration
*a Front view of wire harness connector
(to Park/Neutral Position Switch Assembly)



OK

3.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

NG

8.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM)
3.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
a.
C193931E35
0.085,0.076 0.272,0.252 0.188,0.176 10 *a 0.577,0.259 0.759,0.413 0.182,0.153 10 2L 0.26,0.625 0.391,0.778 0.131,0.153 10 B 0.26,1.68 0.482,1.839 0.222,0.159 10 NL 1.281,1.885 1.503,2.044 0.222,0.159 10 DL 1.727,1.902 1.948,2.061 0.222,0.159 10 PL 2.98,1.369 3.102,1.528 0.122,0.159 10 L 2.16,0.231 2.415,0.390 0.256,0.159 10 RB 2.803,0.613 3.025,0.772 0.222,0.159 10 RL 0.781,0.344 0.903,0.344 0.903,0.344 1.352,0.94 false 0.408,0.713 0.53,0.713 0.53,0.713 1.134,1 false 2.962,1.464 2.84,1.464 2.84,1.464 2.396,1.369 false 0.503,1.753 0.625,1.753 0.625,1.753 1.225,1.462 false 1.499,1.97 1.62,1.97 1.62,1.97 1.794,1.49 false 0.886,1.885 1.107,2.044 0.222,0.159 10 LL 1.086,1.97 1.208,1.97 1.208,1.97 1.381,1.49 false 1.952,1.988 2.074,1.988 2.074,1.988 2.174,1.476 false 2.134,0.33 2.012,0.33 2.012,0.33 1.709,1.04 false 2.782,0.709 2.661,0.709 2.661,0.709 2.069,1.068 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4 (B) - 5 (L) Shift lever in P or N Below 1 Ω
Shift lever not in P and N 10 kΩ or higher
2 (RB) - 6 (PL) Shift lever in P Below 1 Ω
Shift lever not in P 10 kΩ or higher
1 (RL) - 2 (RB) Shift lever in R Below 1 Ω
Shift lever not in R 10 kΩ or higher
2 (RB) - 9 (NL) Shift lever in N Below 1 Ω
Shift lever not in N 10 kΩ or higher
2 (RB) - 7 (DL) Shift lever in D or 3 Below 1 Ω
Shift lever not in D and 3 10 kΩ or higher
2 (RB) - 3 (2L) Shift lever in 2 Below 1 Ω
Shift lever not in 2 10 kΩ or higher
2 (RB) - 8 (LL) Shift lever in L Below 1 Ω
Shift lever not in L 10 kΩ or higher


Text in Illustration
*a Component without harness connected
(Park/Neutral Position Switch Assembly)



OK

4.INSPECT SHIFT LOCK CONTROL UNIT ASSEMBLY (TRANSMISSION CONTROL SWITCH)

NG

4.INSPECT SHIFT LOCK CONTROL UNIT ASSEMBLY (TRANSMISSION CONTROL SWITCH)
a.
C193928E18
0.12,0.035 0.300,0.201 0.180,0.166 10 *a 2.851,0.987 3.270,1.156 0.419,0.170 10 NSSD 1.081,0.099 1.363,0.268 0.282,0.170 10 AT3 1.408,0.189 2.076,0.982 false 2.294,1.043 2.807,1.083 false

Disconnect the transmission control switch connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (NSSD) - 2 (AT3) Shift lever in 3 Below 1 Ω
Shift lever not in 3 10 kΩ or higher


Text in Illustration
*a Component without harness connected
(Shift Lock Control Unit Assembly (Transmission Control Switch))



OK

5.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - TRANSMISSION CONTROL SWITCH)

NG

REPLACE SHIFT LOCK CONTROL UNIT ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - TRANSMISSION CONTROL SWITCH)
a.
U158327E02
0.792,0.563 1.135,1.094 true 0.083,0.052 0.271,0.229 0.188,0.177 10 false *a 0.406,0.958 0.677,1.115 0.271,0.156 10 false F25 0.323,0.469 0.719,0.635 0.396,0.167 10 false NSSD

Connect the park/neutral position switch connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F25-1 (NSSD) - Body ground Ignition switch ON
Shift lever in D or 3
11 to 14 V
Ignition switch ON
Shift lever not in D and 3
Below 1 V


Text in Illustration
*a Front view of wire harness connector
(to Shift Lock Control Unit Assembly (Transmission Control Switch))



OK

6.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - ECM)
a.
U158330E02
2.167,1.042 1.74,0.385 true 0.063,0.021 0.25,0.177 0.188,0.156 10 false *a 0.292,1.042 0.563,1.188 0.271,0.146 10 false A74 1.615,0.281 1.729,0.438 0.115,0.156 10 false 3

Connect the transmission control switch connector.


b.

Disconnect the ECM connector.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A74-26 (3) - Body ground Ignition switch ON
Shift lever in 3
11 to 14 V
Ignition switch ON
Shift lever not in 3
Below 1 V


Text in Illustration
*a Front view of wire harness connector
(to ECM)



OK

7.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM)
U158331E01
0.565,0.23 0.868,0.397 0.303,0.167 10 B84 0.048,0.027 0.258,0.210 0.210,0.182 10 *a 2.151,0.336 2.289,0.486 0.138,0.150 10 D 1.382,1.018 2.118,0.428 false 1.695,0.336 1.833,0.486 0.138,0.150 10 2 1.296,1.018 1.66,0.447 false 1.094,1.822 1.232,1.973 0.138,0.150 10 N 1.21,1.018 1.164,1.794 false 1.386,1.822 1.524,1.973 0.138,0.150 10 P 1.382,1.242 1.456,1.794 false 1.678,1.822 1.817,1.973 0.138,0.150 10 L 1.468,1.242 1.731,1.794 false 0.733,1.822 0.871,1.973 0.138,0.150 10 R 1.124,1.018 0.803,1.794 false

a.

Disconnect the ECM connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B84-73 (P) - Body ground Ignition switch ON
Shift lever in P
11 to 14 V
Ignition switch ON
Shift lever not in P
Below 1 V
B84-53 (R) - Body ground Ignition switch ON
Shift lever R
11 to 14 V*
Ignition switch ON
Shift lever not in R
Below 1 V
B84-54 (N) - Body ground Ignition switch ON
Shift lever in N
11 to 14 V
Ignition switch ON
Shift lever not in N
Below 1 V
B84-56 (D) - Body ground Ignition switch ON
Shift lever in D or 3
11 to 14 V
Ignition switch ON
Shift lever not in D and 3
Below 1 V
B84-55 (2) - Body ground Ignition switch ON
Shift lever in 2
11 to 14 V
Ignition switch ON
Shift lever not in 2
Below 1 V
B84-74 (L) - Body ground Ignition switch ON
Shift lever in L
11 to 14 V
Ignition switch ON
Shift lever not in L
Below 1 V


HINT:

*: The voltage will drop slightly due to the back up light being turned on.


Text in Illustration
*a Front view of wire harness connector
(to ECM)



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM)
a.

Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B84-52 (NSW) - B69-4 (B) Always Below 1 Ω
B69-4 (B) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR