DATA LIST
Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Warm up the engine.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data.
In accordance with the display on the tester, read the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| N Range Status | Judgment for shift lever N position/
OFF or ON |
·
OFF: Shift lever not in N ·
ON: Shift lever in N |
- |
| Neutral Position SW Signal | PNP switch Status/
OFF or ON |
·
OFF: Shift lever not in P and N ·
ON: Shift lever in P or N |
When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect.
|
| Stop Light Switch | Stop light switch status/
OFF or ON |
·
OFF: Brake pedal is released ·
ON: Brake pedal is depressed |
- |
| SPD (NT) | Input turbine speed/
display: 50 rpm min.: 0 rpm max.: 12750 rpm |
·
Input turbine speed (NT) equal to engine speed: Lock-up ON (After warming up engine) ·
Input turbine speed (NT) nearly equal to engine speed: Lock-up OFF (Idling in P or N position) ·
0 rpm: Vehicle stopped in R position |
- |
| Shift SW Status (P Range) | PNP switch Status/
OFF or ON |
·
OFF: Shift lever not in P ·
ON: Shift lever in P |
When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect.
|
| Shift SW Status (R Range) | PNP switch Status/
OFF or ON |
·
OFF: Shift lever not in R ·
ON: Shift lever in R |
|
| Shift SW Status (2 Range) | PNP switch Status/
OFF or ON |
·
OFF: Shift lever not in 2 ·
ON: Shift lever in 2 |
|
| Shift SW Status (L Range) | PNP switch Status/
OFF or ON |
·
OFF: Shift lever not in L ·
ON: Shift lever in L |
|
| Shift SW Status (N Range) | PNP switch Status/
OFF or ON |
·
OFF: Shift lever not in N ·
ON: Shift lever in N |
|
| Shift SW Status (D Range) | PNP switch Status/
OFF or ON |
·
OFF: Shift lever not in D ·
ON: Shift lever in D |
|
| Shift SW Status (3 Range) | PNP switch Status/
OFF or ON |
·
OFF: Shift lever not in 3 ·
ON: Shift lever in 3 |
|
| A/T Oil Temperature 1 | ATF temperature Sensor Value/
min.: -40°C (-40°F) max.: 215°C (419°F) |
·
Approximately 80°C (176°F): After Stall Test ·
Equal to ambient temperature while engine is cold |
If the value is "-40°C (-40°F)" or "150°C (302°F) or more ", ATF temperature sensor circuit is opened or shorted. |
| Lock Up | Lock Up status/
OFF or ON |
·
OFF: Lock up not operating ·
ON: Lock up operating |
- |
| ST Solenoid Status | Shift Solenoid ST Status/
OFF or ON |
OFF → ON → OFF: Up-shifting and down-shifting between 3rd and 4th gears while driving | - |
| Shift Status | Actual Gear Position/
1st, 2nd, 3rd or 4th |
Same as actual gear | - |
| SLT Solenoid Status | Shift Solenoid SLT Status/
OFF or ON |
·
OFF: Accelerator pedal is depressed ·
ON: Accelerator pedal is released |
- |
| SL Solenoid Status | Shift Solenoid SL Status/
OFF or ON |
·
OFF: Lock Up ·
ON: Except Lock Up |
- |
ACTIVE TEST
Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
It is possible to display the Data List during the Active Test.
Warm up the engine.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Select the following items: Powertrain / Engine and ECT / Active Test.
In accordance with the display on the tester, perform the Active Test.
| Tester Display | Test Part | Control Range | Diagnostic Note |
|---|---|---|---|
| Activate the Solenoid (SLT)* | [Test Details]
Operate shift solenoid SLT and raise the line pressure.
|
ON/OFF | [Vehicle Condition]
·
Vehicle stopped ·
Shift lever in P or N ·
Vehicle speed sensor normal ·
Accelerator pedal is released |
| Activate the Solenoid (S1) | [Test Details]
Operate shift solenoid S1 |
ON/OFF | [Vehicle Condition]
·
Engine stopped ·
Vehicle stopped ·
Shift lever in P or N ·
Vehicle speed sensor normal ·
Transmission control switch normal |
| Activate the Solenoid (S2) | [Test Details]
Operate shift solenoid S2 |
ON/OFF | [Vehicle Condition]
·
Engine stopped ·
Vehicle stopped ·
Shift lever in P or N ·
Vehicle speed sensor normal ·
Transmission control switch normal |
| Activate the Lock Up | [Test Details]
Control shift solenoid SL to set automatic transaxle to lock-up condition. |
ON/OFF | Possible to check SL operation.
[Vehicle Condition] ·
Throttle valve opening angle: 20% or more ·
Vehicle speed: 70 km/h (43 mph) or more ·
Gear: Highest gear |
| Activate the Solenoid (SL) | [Test Details]
Operate shift solenoid SL |
ON/OFF | [Vehicle Condition]
·
Engine stopped ·
Vehicle stopped ·
Shift lever in P or N ·
Vehicle speed sensor normal ·
Transmission control switch normal |
| Control the Shift Position | [Test Details]
Operate shift solenoid valve and set each shift position manually. [Others] ·
Press →button: Shift up ·
Press ←button: Shift down |
1st/2nd/3rd/4th | Possible to check operation of shift solenoid valves.
[Vehicle Condition] Vehicle speed: Less than 50 km/h (30 mph) |
| Activate the Solenoid (ST) | [Test Details]
Operate shift solenoid ST |
ON/OFF | [Vehicle Condition]
·
Vehicle stopped ·
Shift lever in P or N ·
Vehicle speed sensor normal |
*: Activate the Solenoid (SLT) in the Active Test is performed to check the line pressure changes by connecting SST to the automatic transaxle, which is used in the Hydraulic Test (See page Drivetrain>U441E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>HYDRAULIC TEST) as well.
The pressure values in Active Test and Hydraulic Test are different from each other.