Home › Drivetrain › CLUTCH › CLUTCH PEDAL(for LHD)
RM19S0E _52 Drivetrain _051467 CLUTCH _0248186 CLUTCH PEDAL(for LHD) A

CLUTCH  CLUTCH PEDAL(for LHD)  INSTALLATION  


PROCEDURE

Hide 31321 1.INSTALL CLUTCH PEDAL PAD

a.

Install the clutch pedal pad to the clutch pedal sub-assembly.


Hide 31301B 2.INSTALL NO. 1 CLUTCH PEDAL CUSHION

a.

Install the No. 1 clutch pedal cushion to the clutch pedal sub-assembly.


Hide 31324A 3.INSTALL CLUTCH PEDAL SHAFT COLLAR

a.
C242407

Apply MP grease to both sides of 2 new clutch pedal bushes.

Text in Illustration
V100135

MP grease


b.

Install the 2 clutch pedal bushes and the clutch pedal shaft collar to the clutch pedal sub-assembly.


Hide 31301 4.INSTALL CLUTCH PEDAL SUB-ASSEMBLY

a.

Install the clutch pedal sub-assembly to the clutch pedal support sub-assembly with the bolt and the nut.

Torque:
37 N*m (375 kgf*cm, 27 ft.*lbf)

NOTICE:

Turn the nut while holding the bolt.



Hide 31301A 5.INSTALL CLUTCH PEDAL SPRING

a.

Install the clutch pedal spring to the clutch pedal sub-assembly and the clutch pedal support sub-assembly.


Hide 31301F 6.INSTALL CLUTCH PEDAL STOPPER BOLT

a.

Install the clutch pedal stopper bolt to the clutch pedal support sub-assembly and temporarily tighten the lock nut.

HINT:

Tighten the lock nut to the specified torque when adjusting the clutch pedal.



Hide 84520 7.INSTALL CLUTCH START SWITCH ASSEMBLY

a.

Install the clutch start switch assembly to the clutch pedal support sub-assembly with the nut.

Torque:
16 N*m (160 kgf*cm, 12 ft.*lbf)


Hide 55107A 8.INSTALL CLUTCH PEDAL SUPPORT SUB-ASSEMBLY

a.
C247293

Apply MP grease to the contact surface of the clutch master cylinder push rod clevis and the clutch pedal sub-assembly.

Text in Illustration
V100135

MP grease


b.

Install the clutch master cylinder push rod clevis to the cutout of the clutch pedal sub-assembly from the left side of the vehicle and push it downward.


c.

Install the clutch pedal support sub-assembly to the vehicle with the bolt and the 2 nuts.

Torque:
for Bolt : 24 N*m (241 kgf*cm, 17 ft.*lbf)
for Nut : 9.0 N*m (92 kgf*cm, 80 in.*lbf)


d.

Connect the connector and engage the wire harness clamp.


e.
C247291E01
0.618,2.905 0.788,3.065 0.170,0.161 10 *a

With the clutch pedal fully depressed, check that the clearance shown in the illustration is as specified.

Text in Illustration
*a Clearance
V100135

Fully depressed

Standard clearance:
for 1NZ-FE:

2.1 to 5.1 mm (0.083 to 0.201 in.)

for 2NZ-FE:

2.0 to 5.0 mm (0.079 to 0.197 in.)



Hide 9.INSPECT AND ADJUST CLUTCH PEDAL

Hide 83100 10.INSTALL COMBINATION METER ASSEMBLY

Hide 55432B 11.INSTALL LOWER INSTRUMENT PANEL FINISH PANEL

Hide 55433D 12.INSTALL LOWER NO. 2 INSTRUMENT PANEL FINISH PANEL

Hide 55606 13.INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY