Home › Drivetrain › CLUTCH › CLUTCH PEDAL(for RHD) › 2011.08–2014.07
RM19S0E _52 Drivetrain _051467 CLUTCH _0248187 CLUTCH PEDAL(for RHD) A

CLUTCH  CLUTCH PEDAL(for RHD)  INSTALLATION  


PROCEDURE

Hide 31321 1.INSTALL CLUTCH PEDAL PAD

a.

Install the clutch pedal pad to the clutch pedal sub-assembly.


Hide 31322 2.INSTALL CLUTCH PEDAL STOPPER

a.

Install the clutch pedal stopper to the clutch pedal sub-assembly.


Hide 31301B 3.INSTALL NO. 1 CLUTCH PEDAL CUSHION

a.

Install the No. 1 clutch pedal cushion to the clutch pedal sub-assembly.


Hide 31453B 4.INSTALL CLUTCH MASTER CYLINDER PUSH ROD CLEVIS BUSH

a.

Install a new clutch master cylinder push rod clevis bush to the clutch pedal sub-assembly.

HINT:

Install the clutch master cylinder push rod clevis bush from the right side of the vehicle.



b.
C235134

Apply MP grease to the inside of the clutch master cylinder push rod clevis bush.

Text in Illustration
V100135

MP grease


Hide 31324A 5.INSTALL CLUTCH PEDAL SHAFT COLLAR

a.
C235135

Apply MP grease to both sides of 2 new clutch pedal bushes.

Text in Illustration
V100135

MP grease


b.

Install the 2 clutch pedal bushes and the clutch pedal shaft collar to the clutch pedal sub-assembly.


Hide 31301 6.INSTALL CLUTCH PEDAL SUB-ASSEMBLY

a.

Install the clutch pedal sub-assembly to the clutch pedal support sub-assembly with the bolt and the nut.

Torque:
37 N*m (375 kgf*cm, 27 ft.*lbf)

NOTICE:

Turn the nut while holding the bolt.



Hide 31301A 7.INSTALL CLUTCH PEDAL SPRING

a.

Install the clutch pedal spring to the clutch pedal sub-assembly and the clutch pedal support sub-assembly.


Hide 31301F 8.INSTALL CLUTCH PEDAL STOPPER BOLT

a.

Install the clutch pedal stopper bolt to the clutch pedal support sub-assembly and temporarily tighten the lock nut.

HINT:

Tighten the lock nut to the specified torque when adjusting the clutch pedal.



Hide 84520E 9.INSTALL NO. 2 CLUTCH START SWITCH ASSEMBLY (w/ Cruise Control System)

a.

Install the No. 2 clutch start switch assembly to the clutch pedal support sub-assembly with the nut.

Torque:
16 N*m (160 kgf*cm, 12 ft.*lbf)


Hide 84520 10.INSTALL CLUTCH START SWITCH ASSEMBLY

a.

Install the clutch start switch assembly to the clutch pedal support sub-assembly with the nut.

Torque:
16 N*m (160 kgf*cm, 12 ft.*lbf)


Hide 55107A 11.INSTALL CLUTCH PEDAL SUPPORT SUB-ASSEMBLY

a.

Install the clutch pedal support sub-assembly to the vehicle with the 2 nuts.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)


b.

Install the 2 bolts to the clutch pedal support sub-assembly.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)


c.
C245271

Apply MP grease to the clevis pin.

Text in Illustration
V100135

MP grease


d.

Install the clutch master cylinder push rod clevis to the clutch pedal sub-assembly with the clevis pin and a new clip.

HINT:

Install the clevis pin from the right side of the vehicle.



e.

Connect the connectors and engage the wire harness clamps.


f.
C242394E01
0.721,2.985 0.891,3.146 0.17,0.161 10 *a

With the clutch pedal fully depressed, check that the clearance shown in the illustration is as specified.

Text in Illustration
*a Clearance
V100135

Fully depressed

Standard clearance:

2.5 to 5.5 mm (0.098 to 0.217 in.)



Hide 12.INSPECT AND ADJUST CLUTCH PEDAL

Hide 84520E 13.INSPECT NO. 2 CLUTCH START SWITCH ASSEMBLY (w/ Cruise Control System)

a.
C245183E01
2.111,2.263 2.280,2.424 0.170,0.161 10 *a

Without depressing the clutch pedal, check that the clearance shown in the illustration is as specified.

Text in Illustration
*a Clearance

Standard clearance:
for 1NZ-FE:

0.5 to 3.5 mm (0.020 to 0.138 in.)

for 2NZ-FE:

2.5 to 5.5 mm (0.098 to 0.217 in.)



Hide 55432B 14.INSTALL LOWER INSTRUMENT PANEL FINISH PANEL (w/o Knee Airbag)

Hide 73900 15.INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (w/ Knee Airbag)

HINT:

Use the same procedure as for LHD models (See page Vehicle Interior>INTERIOR PANELS / TRIM>LOWER INSTRUMENT PANEL>INSTALLATION).


Hide 55606 16.INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

HINT:

Use the same procedure as for LHD models (See page Vehicle Interior>INTERIOR PANELS / TRIM>LOWER INSTRUMENT PANEL>INSTALLATION).