31321
1.INSTALL CLUTCH PEDAL PAD
Install the clutch pedal pad to the clutch pedal sub-assembly.
31322
2.INSTALL CLUTCH PEDAL STOPPER
Install the clutch pedal stopper to the clutch pedal sub-assembly.
31301B
3.INSTALL NO. 1 CLUTCH PEDAL CUSHION
Install the No. 1 clutch pedal cushion to the clutch pedal sub-assembly.
31453B
4.INSTALL CLUTCH MASTER CYLINDER PUSH ROD CLEVIS BUSH
Install a new clutch master cylinder push rod clevis bush to the clutch pedal sub-assembly.
Install the clutch master cylinder push rod clevis bush from the right side of the vehicle.
Apply MP grease to the inside of the clutch master cylinder push rod clevis bush.
|
MP grease |
31324A
5.INSTALL CLUTCH PEDAL SHAFT COLLAR
Apply MP grease to both sides of 2 new clutch pedal bushes.
|
MP grease |
Install the 2 clutch pedal bushes and the clutch pedal shaft collar to the clutch pedal sub-assembly.
31301
6.INSTALL CLUTCH PEDAL SUB-ASSEMBLY
Install the clutch pedal sub-assembly to the clutch pedal support sub-assembly with the bolt and the nut.
Turn the nut while holding the bolt.
31301A
7.INSTALL CLUTCH PEDAL SPRING
Install the clutch pedal spring to the clutch pedal sub-assembly and the clutch pedal support sub-assembly.
31301F
8.INSTALL CLUTCH PEDAL STOPPER BOLT
Install the clutch pedal stopper bolt to the clutch pedal support sub-assembly and temporarily tighten the lock nut.
Tighten the lock nut to the specified torque when adjusting the clutch pedal.
84520E
9.INSTALL NO. 2 CLUTCH START SWITCH ASSEMBLY (w/ Cruise Control System)
Install the No. 2 clutch start switch assembly to the clutch pedal support sub-assembly with the nut.
84520
10.INSTALL CLUTCH START SWITCH ASSEMBLY
Install the clutch start switch assembly to the clutch pedal support sub-assembly with the nut.
55107A
11.INSTALL CLUTCH PEDAL SUPPORT SUB-ASSEMBLY
Install the clutch pedal support sub-assembly to the vehicle with the 2 nuts.
Install the 2 bolts to the clutch pedal support sub-assembly.
Apply MP grease to the clevis pin.
|
MP grease |
Install the clutch master cylinder push rod clevis to the clutch pedal sub-assembly with the clevis pin and a new clip.
Install the clevis pin from the right side of the vehicle.
Connect the connectors and engage the wire harness clamps.
With the clutch pedal fully depressed, check that the clearance shown in the illustration is as specified.
| *a | Clearance |
|
Fully depressed |
2.5 to 5.5 mm (0.098 to 0.217 in.)
12.INSPECT AND ADJUST CLUTCH PEDAL
84520E
13.INSPECT NO. 2 CLUTCH START SWITCH ASSEMBLY (w/ Cruise Control System)
Without depressing the clutch pedal, check that the clearance shown in the illustration is as specified.
| *a | Clearance |
0.5 to 3.5 mm (0.020 to 0.138 in.)
2.5 to 5.5 mm (0.098 to 0.217 in.)
73900
14.INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (w/ Knee Airbag)
Use the same procedure as for LHD models (See page Vehicle Interior>INTERIOR PANELS / TRIM>LOWER INSTRUMENT PANEL>INSTALLATION).
55606
15.INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY
Use the same procedure as for LHD models (See page Vehicle Interior>INTERIOR PANELS / TRIM>LOWER INSTRUMENT PANEL>INSTALLATION).
16.INSPECT CLUTCH START SYSTEM