Home › Drivetrain › CLUTCH › CLUTCH UNIT
RM19S0E _52 Drivetrain _051467 CLUTCH _0248191 CLUTCH UNIT A

CLUTCH  CLUTCH UNIT  INSTALLATION  


PROCEDURE

Hide 31250 1.INSTALL CLUTCH DISC ASSEMBLY

a.
C235155E01
2.56,1.872 2.850,2.014 0.290,0.142 10 SST 2.276,1.866 2.54,1.955 false 0.812,3.795 1.102,3.937 0.290,0.142 10 SST 1.77,2.708 1.461,2.652 false 1.293,2.56 1.443,2.702 0.150,0.142 10 *1 2.29,2.56 2.440,2.702 0.150,0.142 10 *2 2.068,2.777 2.29,2.685 false 1.072,3.56 0.99,3.778 false

Insert SST into the clutch disc assembly, and then insert them both into the flywheel sub-assembly.

Text in Illustration
*1 Clutch Disc Assembly
*2 Flywheel Sub-assembly

SST
09301-00210  

NOTICE:

Insert clutch disc assembly in the correct direction.



Hide 31210 2.INSTALL CLUTCH COVER ASSEMBLY

a.
C235156E01
0.547,1.422 0.702,1.566 0.155,0.144 10 *a 0.984,1.551 0.737,1.534 0.737,1.534 0.916,1.608 false 2.484,0.054 2.589,0.192 0.105,0.137 10 1 2.931,1.094 3.036,1.232 0.105,0.137 10 5 2.421,2.002 2.526,2.140 0.105,0.137 10 2 0.865,2.002 0.970,2.140 0.105,0.137 10 6 0.364,0.948 0.469,1.085 0.105,0.137 10 3 0.908,0.02 1.013,0.157 0.105,0.137 10 7 2.581,0.037 2.836,0.198 0.254,0.161 10 (*b) 2.873,0.054 3.055,0.203 0.182,0.150 10 , 4 2.695,1.627 2.984,1.764 0.288,0.137 10 SST 2.023,1.239 2.667,1.696 false

Align the matchmark on the clutch cover assembly with that on the flywheel sub-assembly.

Text in Illustration
*a Matchmark
*b Temporarily

SST
09301-00210  


b.

Following the procedures shown in the illustration, tighten the 6 bolts in order, starting with the bolt located near the knock pin at the top.

Torque:
19 N*m (195 kgf*cm, 14 ft.*lbf)

HINT:
·

Following the order in the illustration, tighten the bolts evenly one at a time.

·

Move SST up and down, right and left lightly after checking that the disc is in the center, and tighten the bolts.




Hide 31210 3.INSPECT AND ADJUST CLUTCH COVER ASSEMBLY

a.
C235157

Using a dial indicator with a roller instrument, measure the diaphragm spring tip alignment.

Maximum non-alignment:

0.5 mm (0.0197 in.)



b.
C235158E01
2.616,0.808 2.907,0.955 0.292,0.147 10 SST 2.101,1.262 2.577,0.895 false

If the alignment is not as specified, using SST, adjust the diaphragm spring tip alignment.

SST
09333-00013  


Hide 31236B 4.INSTALL RELEASE FORK SUPPORT

a.

Install the release fork support to the manual transaxle assembly.

Torque:
37 N*m (375 kgf*cm, 27 ft.*lbf)


Hide 31126 5.INSTALL CLUTCH RELEASE FORK BOOT

a.

Install the clutch release fork boot to the manual transaxle assembly.


Hide 31232A 6.INSTALL RELEASE BEARING HUB CLIP

a.

Install the release bearing hub clip to the clutch release bearing assembly.


Hide 31204 7.INSTALL CLUTCH RELEASE FORK SUB-ASSEMBLY

a.
C246398

Apply release hub grease to the contact surfaces of the clutch release fork sub-assembly and clutch release bearing assembly, clutch release fork sub-assembly and No. 1 clutch release cylinder push rod, and clutch release fork sub-assembly and release fork support.

Text in Illustration
V100135

Clutch Release Hub Grease

Grease:

Toyota Genuine Clutch Release Hub Grease or equivalent (mineral ingredients should not be included)



b.

Engage the release bearing hub clip and install the clutch release fork sub-assembly to the clutch release bearing assembly.


Hide 31230 8.INSTALL CLUTCH RELEASE BEARING ASSEMBLY

a.
U134704E01
1.51,0.974 1.671,0.801 false 1.593,0.863 1.708,1.000 0.114,0.137 10 A

Apply clutch spline grease to the input shaft spline.

Text in Illustration
V100135

Clutch Spline Grease

Grease:

Toyota Genuine Clutch Spline Grease or equivalent


NOTICE:

Do not apply grease to portion A shown in the illustration.



b.

Install the clutch release bearing assembly with the clutch release fork sub-assembly to the manual transaxle assembly.

NOTICE:

After the installation, move the fork forward and backward to check that the release bearing slides smoothly.