Home › Drivetrain › C54 MANUAL TRANSMISSION / TRANSAXLE › MANUAL TRANSAXLE ASSEMBLY › 2011.08–2014.07
RM19S0E _52 Drivetrain _051468 C54 MANUAL TRANSMISSION / TRANSAXLE _0248199 MANUAL TRANSAXLE ASSEMBLY A

C54 MANUAL TRANSMISSION / TRANSAXLE  MANUAL TRANSAXLE ASSEMBLY  INSTALLATION  


PROCEDURE

Hide 1.INSTALL WIRE HARNESS CLAMP BRACKET

a.

Install the 3 wire harness clamp brackets with 3 bolts to the manual transaxle assembly.

Torque:
13 N*m (130 kgf*cm, 9 ft.*lbf)


Hide 33403K 2.INSTALL SPEEDOMETER DRIVEN HOLE COVER SUB-ASSEMBLY (w/ ABS)

a.

Coat a new O-ring with manual transaxle gear oil and install it to the speedometer driven hole cover sub-assembly.


b.

Install the speedometer driven hole cover sub-assembly with the bolt.

Torque:
11 N*m (115 kgf*cm, 8 ft.*lbf)


Hide 83181G 3.INSTALL SPEEDOMETER SENSOR (w/o ABS)

a.

Coat a new O-ring with manual transaxle gear oil and install it to the speedometer sensor.


b.

Install the speedometer driven gear to the speedometer sensor with the E-ring.


c.

Install the speedometer sensor with the bolt.

Torque:
11 N*m (115 kgf*cm, 8 ft.*lbf)


Hide 30300 4.INSTALL MANUAL TRANSAXLE ASSEMBLY

a.

Align the input shaft with the clutch disc and install the manual transaxle assembly to the engine assembly.


b.

Install the 7 bolts.

Torque:
33 N*m (336 kgf*cm, 24 ft.*lbf)

NOTICE:
·

Insert knock pins into the knock pin holes securely so that the end face of the manual transaxle fits close against the engine before tightening the bolts.

·

Be careful not to pinch wire harness, etc.

·

To avoid damage to the input shaft, do not forcefully shake the manual transaxle.




Hide 12325A 5.INSTALL TRANSVERSE ENGINE ENGINE MOUNTING BRACKET

a.

Remove any adhesive remaining in the 4 bolts holes on the manual transaxle assembly and 4 bolts.


b.
A057108

Apply adhesive to 2 or 3 threads on the end of the 4 bolts.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent.



c.
U158292E02
1.344,1.729 1.969,1.927 0.625,0.198 10 true 1 (*a), 5 1.615,1.26 1.729,1.427 0.115,0.167 10 false 2 1.438,0.542 1.552,0.708 0.115,0.167 10 false 3 2.333,1.792 2.5,1.99 0.167,0.198 10 true 4

Following the procedures shown in the illustration, Tighten the 4 bolts in order.

Text in Illustration
*a Temporarily

Torque:
64 N*m (653 kgf*cm, 47 ft.*lbf)


Hide 12372A 6.INSTALL TRANSVERSE ENGINE ENGINE MOUNTING INSULATOR

a.
C235562E02
2.656,0.271 3.198,0.448 0.542,0.177 10 false 1 (*a), 6 1.99,0.875 2.531,1.052 0.542,0.177 10 true 2 (*a), 7 1.74,1.906 1.865,2.083 0.125,0.177 10 true 3 1.073,1.135 1.198,1.292 0.125,0.156 10 true 4 2.385,1.177 2.51,1.333 0.125,0.156 10 true 5

Following the procedures shown in the illustration, Tighten the 5 bolts in order.

Torque:
52 N*m (530 kgf*cm, 38 ft.*lbf)


b.

Install the transverse engine engine mounting bracket and the transverse engine engine mounting insulator with the bolt and nut.

Torque:
52 N*m (530 kgf*cm, 38 ft.*lbf)

HINT:

Hold the nut and tighten the bolt.



Hide 12313 7.INSTALL TRANSVERSE ENGINE ENGINE MOUNTING CONTROL BRACKET

a.
C116856E02
1.271,0.448 1.896,0.625 0.625,0.177 10 true 1 (*a), 5 0.75,1.833 0.854,1.979 0.104,0.146 10 false 2 2.156,1.74 2.26,1.885 0.104,0.146 10 true 3 2.823,1.094 2.927,1.24 0.104,0.146 10 true 4

Following the procedures shown in the illustration, tighten the 4 bolts in order.

Text in Illustration
*a Temporarily

Torque:
45 N*m (459 kgf*cm, 33 ft.*lbf)


Hide 51201 8.INSTALL FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY

Hide 43420 9.INSTALL FRONT DRIVE SHAFT ASSEMBLIES

Hide 10.CONNECT WIRE HARNESS (w/ ABS)

a.

Connect the back up light switch connector.


b.

Install the ground wire with the bolt.

Torque:
26 N*m (260 kgf*cm, 19 ft.*lbf)


c.

Connect the 4 clamps and install the wire harness with the bolt.

Torque:
13 N*m (130 kgf*cm, 9 ft.*lbf)


Hide 11.CONNECT WIRE HARNESS (w/o ABS)

a.

Connect the speedometer sensor connector.


b.

Connect the back up light switch connector.


c.

Install the ground wire with the bolt.

Torque:
26 N*m (260 kgf*cm, 19 ft.*lbf)


d.

Connect the 4 clamps and install the wire harness with the bolt.

Torque:
13 N*m (130 kgf*cm, 9 ft.*lbf)


Hide 12.INSTALL CONTROL CABLE BRACKET

a.

Install the control cable bracket with the 2 bolts.

Torque:
25 N*m (250 kgf*cm, 18 ft.*lbf)


Hide 33820B 13.INSTALL TRANSMISSION CONTROL CABLE ASSEMBLY

a.

Connect the 2 transmission control cable ends and install the 2 washers and the 2 clips.


b.

Install 2 new clips onto the control cable bracket.


Hide 31470 14.INSTALL CLUTCH RELEASE CYLINDER ASSEMBLY

a.

Install the clutch release cylinder assembly and the clutch pipe with the 4 bolts.

Torque:
12 N*m (120 kgf*cm, 9 ft.*lbf)


Hide 28100 15.INSTALL STARTER ASSEMBLY (for 1NZ-FE)

Hide 28100 16.INSTALL STARTER ASSEMBLY (for 2NZ-FE)

Hide 74431 19.INSTALL BATTERY TRAY

Hide 55711 23.INSTALL OUTER COWL TOP PANEL (for LHD)

Hide 55711 24.INSTALL OUTER COWL TOP PANEL (for RHD)

Hide 55722C 25.INSTALL INNER COWL TOP TO COWL BRACE (for LHD)

Hide 55722C 26.INSTALL INNER COWL TOP TO COWL BRACE (for RHD)

Hide 55815E 27.INSTALL FRONT NO. 1 VENTILATOR SEAL (for LHD)

Hide 55815E 28.INSTALL FRONT NO. 1 VENTILATOR SEAL (for RHD)

Hide 55735D 29.INSTALL FRONT AIR SHUTTER SEAL RH (for LHD)

Hide 55735D 30.INSTALL FRONT AIR SHUTTER SEAL RH (for RHD)

Hide 31.INSTALL FRONT WIPER MOTOR AND LINK

Hide 34.INSPECT FOR MANUAL TRANSAXLE OIL LEAK