Home › Drivetrain › C54 MANUAL TRANSMISSION / TRANSAXLE › TRANSMISSION CONTROL CABLE › from 2014.07
RM19S0E _52 Drivetrain _051468 C54 MANUAL TRANSMISSION / TRANSAXLE _0248196 TRANSMISSION CONTROL CABLE A

C54 MANUAL TRANSMISSION / TRANSAXLE  TRANSMISSION CONTROL CABLE  INSTALLATION  


PROCEDURE

Hide 33820B 1.INSTALL TRANSMISSION CONTROL CABLE ASSEMBLY

a.

Install the transmission control cable assembly to the vehicle with the 3 nuts.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


b.
C303458E01
1.617,0.158 1.786,0.318 0.170,0.161 10 *1 1.8,0.26 2.044,0.407 false 1.101,0.984 1.271,1.144 0.170,0.161 10 *2 1.285,1.069 1.529,0.937 false

Pass the transmission control cable assembly under the transmission control cable support.

Text in Illustration
*1 Transmission Control Cable Assembly
*2 Transmission Control Cable Support

NOTICE:

Do not pass the transmission control cable assembly between the transmission control cable support and dash panel.



c.
C235168E07
2.208,1.74 2.396,1.896 0.188,0.156 10 true *1 1.417,0.271 1.604,0.427 0.188,0.156 10 false *2 2.896,0.958 3.083,1.115 0.188,0.156 10 false *2 0.125,1.635 0.313,1.792 0.188,0.156 10 false *1

Install the transmission control cable assembly to the control cable bracket with 2 new clips B.

Text in Illustration
*1 Clip A
*2 Clip B


d.

Connect the transmission control cable assembly to the manual transaxle assembly with the 2 washers and 2 clips A.


Hide 33820B 2.CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

a.
C288539E01
0.658,1.858 0.827,2.019 0.170,0.161 10 *1 2.789,0.501 2.959,0.661 0.170,0.161 10 *2 1.357,1.673 0.844,1.93 false 2.76,0.614 2.247,0.872 false

Rotate the 2 nuts of the transmission control cable assembly approximately 180° in the direction shown in the illustration, and while holding the nut, push in the lock.

Text in Illustration
*1 Nut
*2 Lock
V100135

Rotate approximately 180°
V100136

Push in

NOTICE:

Do not rotate the nut excessively as it may damage the internal spring and the transmission control cable assembly will not be reusable.



b.
C355425E02
1.281,0.354 1.115,0.24 false 1.656,0.198 1.813,0.396 0.156,0.198 10 false A 0.844,0.896 1,1.094 0.156,0.198 10 true A 2.156,3.021 2.469,3.219 0.313,0.198 10 false *1 2.688,3.063 2.896,3.26 0.208,0.198 10 true *2 0.948,0.125 1.26,0.323 0.313,0.198 10 false *3

Install the transmission control cable assembly to the floor shift shift lever assembly.

Text in Illustration
*1 Clip A
*2 Clip B
*3 Lock

NOTICE:

After installation, make sure that the lock is projecting from A as shown in the illustration.



c.

Engage the clip B to connect the shift cable end of the transmission control cable assembly to the floor shift shift lever assembly.


d.

Connect the select cable end of the transmission control cable assembly to the floor shift shift lever assembly with the clip A.

NOTICE:

Install the end of the transmission control cable assembly so that its adjustment lock section is on the driver side.



Hide 58151 4.INSTALL FRONT NO. 1 FLOOR HEAT INSULATOR

a.

Install the front No. 1 floor heat insulator to the vehicle with the 2 bolts and nut.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


Hide 74431 10.INSTALL BATTERY TRAY

Hide 58910C 12.INSTALL REAR CONSOLE BOX ASSEMBLY

Hide 13.INSPECT FOR EXHAUST GAS LEAK