Home › Drivetrain › DRIVE SHAFT / PROPELLER SHAFT › FRONT DRIVE SHAFT ASSEMBLY
RM19S0E _52 Drivetrain _051469 DRIVE SHAFT / PROPELLER SHAFT _0248206 FRONT DRIVE SHAFT ASSEMBLY A

DRIVE SHAFT / PROPELLER SHAFT  FRONT DRIVE SHAFT ASSEMBLY  REASSEMBLY  


PROCEDURE

Hide 41336E 1.INSTALL FRONT DRIVE SHAFT DUST COVER

a.
C306547E01
0.154,1.024 0.463,1.199 0.309,0.175 10 SST 0.876,1.287 0.515,1.113 0.515,1.113 0.993,1.591 false 0.646,0.127 0.816,0.306 0.170,0.179 10 *a 0.835,0.217 1.165,0.251 false

Using SST and a press, install a new front drive shaft dust cover to the front drive inboard joint assembly until it is flush with the end.

Text in Illustration
*a Press

SST
09527-10011  

NOTICE:
·

Install the front drive shaft dust cover in the correct orientation.

·

Do not deform the front drive shaft dust cover.




Hide 43420G 2.INSTALL FRONT DRIVE SHAFT HOLE SNAP RING LH

a.

Install a new front drive shaft hole snap ring LH.


Hide 43410N 3.INSTALL FRONT DRIVE SHAFT HOLE SNAP RING RH

HINT:

Use the same procedure for the RH side as for the LH side.


Hide 4.INSTALL FRONT AXLE OUTBOARD JOINT BOOT

a.
C177228E04
2.537,1.055 2.752,1.225 0.215,0.170 10 *a 2.05,0.848 2.483,1.149 false

Wrap the spline of the front drive outboard joint shaft assembly with protective tape.

Text in Illustration
*a Protective Tape


b.

Install new parts to the front drive outboard joint shaft assembly in the following order.

i.

Front No. 2 axle outboard joint boot clamp


ii.

Front axle outboard joint boot


iii.

Front axle outboard joint boot clamp



c.

Pack the joint portion of the front drive outboard joint shaft assembly and front axle outboard joint boot with grease.

Standard Grease Capacity:
Drive Shaft Type Grease Capacity
Type A 90 to 100 g (3.2 to 3.5 oz.)
Type B 116 to 126 g (4.1 to 4.4 oz.)


HINT:
C306538E02
0.365,1.05 0.576,1.215 0.210,0.165 10 (A)

Measure the diameter (A) as shown in the illustration to determine the drive shaft type.


Diameter (A):
Drive Shaft Type Diameter
Type A 23.65 mm (0.931 in.)
Type B 24.10 mm (0.949 in.)



d.

Install the front axle outboard joint boot to the front drive outboard joint shaft assembly groove.

NOTICE:

Keep the groove free of grease.



Hide 43447D 5.INSTALL FRONT NO. 2 AXLE OUTBOARD JOINT BOOT CLAMP

CAUTION:

Wear protective gloves to avoid injuries to your hands.


a.
C415871C01
2.156,1.5 2.677,1.5 false 0.833,1.24 1.354,1.24 false 1.917,2.031 2.438,2.031 false 2.708,1.438 3.021,1.594 0.313,0.156 10 false *a 0.667,1.177 0.979,1.333 0.313,0.156 10 false *b 1.729,1.948 2.042,2.104 0.313,0.156 10 false *c
*a Fulcrum Point
*b Lever Push Position
*c Band Support Position


Install the front No. 2 axle outboard joint boot clamp to the front axle outboard joint boot and temporarily fold back the lever at the fulcrum point.

NOTICE:
·

Set the lever to the guide groove correctly and install the clamp as far to the inside of the vehicle as possible.

·

Check the band and the lever for any deformation before folding back the lever.

·

The lever folds easily at the fulcrum point when pushed at the position shown in the illustration.

·

When folding back the lever, do not push at the end of the lever.

C415873C01
6.771,1.49 6.125,1.49 true 5.948,1.417 6.26,1.573 0.313,0.156 10 false *a
*a Temporary Claw - -


·

If the lever bends in the middle, it may not engage with the temporary claws or may not be held in the correct position.




b.

As shown in the illustration, while pressing the outboard joint area against the work surface, firmly press the lever into place by rolling the outboard joint area forward from the folded fulcrum point to the temporary claw area until a click sound is heard.

C415872C01
3.604,1.052 3.135,1.406 3.135,1.406 3.708,1.042 true 2.083,1.49 1.594,1.49 true 1.958,2.281 1.688,2.281 1.688,2.281 1.448,1.906 true 5.927,2.229 5.646,1.938 5.646,1.938 5.49,1.938 true 3.823,0.292 4.135,0.448 0.313,0.156 10 false *a 4.104,1.302 4.417,1.458 0.313,0.156 10 false *b 5.24,0.583 5.552,0.74 0.313,0.156 10 false *c 2.979,1.354 3.292,1.51 0.313,0.156 10 false *d 1.208,2.365 1.521,2.521 0.313,0.156 10 false *b 1.427,1.417 1.74,1.573 0.313,0.156 10 false *d 2.01,2.219 2.323,2.375 0.313,0.156 10 false *e 5.281,1.875 5.594,2.031 0.313,0.156 10 false *d
*a Press down *b Contact Point
*c Roll forward *d Temporary Claw
*e Fulcrum Point - -


NOTICE:
·

Do not damage the deflector.

·

Make sure that the outboard joint is in direct contact with the work surface.




c.
C265825C09
1.698,3.74 1.135,4.417 1.135,4.417 1.896,3.771 true 0.979,4.406 1.292,4.604 0.313,0.198 10 false *a
*a Buckle


Using a plastic hammer, tap the buckle to secure it while adjusting the clearance between the lever and the groove to make the clearance between the buckle edge and the lever end even.

NOTICE:
·

Do not use excessive force when tapping with the plastic hammer.

·

Do not damage the front axle outboard joint boot.




Hide 43447E 6.INSTALL FRONT AXLE OUTBOARD JOINT BOOT CLAMP

CAUTION:

Wear protective gloves to avoid injuries to your hands.


a.
C107948

Install a new front axle outboard joint boot clamp to the front axle outboard joint boot and provisionally fold back the lever.

NOTICE:
·

Set the lever into the guide groove correctly.

·

Check the band and lever for any deformation before folding back the lever.




b.
C158356E19
2.521,0.948 2.792,1.177 0.271,0.229 10 false *a

Using water pump pliers, pinch the front axle outboard joint boot clamp to provisionally fix it.

Text in Illustration
*a Place the tip near the center of the lever.


c.
C355422

Using a plastic hammer, tap the buckle to fix it while adjusting the clearance between the lever and groove to make the clearances between the buckle edge and lever end even.

NOTICE:

Do not damage the front axle outboard joint boot.



Hide 43474D 7.INSTALL FRONT DRIVE SHAFT DAMPER RH (w/ 1 Clamp)

a.
C306548E01
1.49,0.403 1.726,0.620 0.236,0.217 10 (A)

Install the front drive shaft damper RH to dimension (A) shown in the illustration.

Dimension (A):
Drive Shaft Type Dimension
Type A 416.0 to 420.0 mm
(1.36 to 1.38 ft.)
Type B 425.6 to 429.6 mm
(1.40 to 1.41 ft.)


HINT:
C306538E03
0.365,1.05 0.576,1.215 0.210,0.165 10 (A)

Measure the diameter (A) as shown in the illustration to determine the drive shaft type.


Diameter (A):
Drive Shaft Type Diameter
Type A 23.65 mm (0.931 in.)
Type B 24.10 mm (0.949 in.)



Hide 43474D 8.INSTALL FRONT DRIVE SHAFT DAMPER RH (w/ 2 Clamps)

a.
C306540E01
1.324,0.482 1.534,0.647 0.210,0.165 10 (A)

Install the front drive shaft damper RH to dimension (A) shown in the illustration.

Dimension (A):
Drive Shaft Type Dimension
Type A 452.0 to 456.0 mm
(1.48 to 1.50 ft.)
Type B 461.6 to 465.6 mm
(1.51 to 1.53 ft.)


HINT:
C306538E03
0.365,1.05 0.576,1.215 0.210,0.165 10 (A)

Measure the diameter (A) as shown in the illustration to determine the drive shaft type.


Diameter (A):
Drive Shaft Type Diameter
Type A 23.65 mm (0.931 in.)
Type B 24.10 mm (0.949 in.)



Hide 43474F 9.INSTALL FRONT DRIVE SHAFT DAMPER CLAMP RH (w/ 1 Clamp)

a.

for One Touch Type:

i.
C196491E05
0.079,0.075 0.257,0.257 0.178,0.182 10 *a 0.079,2.27 0.257,2.439 0.178,0.169 10 *b

Install a new front drive shaft damper clamp RH to the front drive shaft damper RH and fix the front drive shaft damper clamp RH with a screwdriver.

Text in Illustration
*a for One Touch Type
*b for Claw Engagement Type



b.

for Claw Engagement Type:

i.

Using needle-nose pliers, engage the 2 claws and install a new front drive shaft damper clamp RH as shown in the illustration.



Hide 43474F 10.INSTALL FRONT DRIVE SHAFT DAMPER CLAMP RH (w/ 2 Clamps)

C306541

a.

Using needle-nose pliers, engage the 4 claws and install 2 new front drive shaft damper clamps RH as shown in the illustration.


Hide 43040 11.INSTALL FRONT DRIVE INBOARD JOINT ASSEMBLY

a.

Install new parts to the front drive outboard joint shaft assembly in the following order.

i.

Front axle inboard joint boot clamp


ii.

Front axle inboard joint boot


iii.

Front No. 2 axle inboard joint boot clamp



b.

Fix the front drive outboard joint shaft assembly in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



c.

Remove the protective tape.


d.
F047445E15
2.063,1.323 2.219,1.771 2.219,1.771 1.521,1.625 true 2.26,1.75 2.427,1.896 0.167,0.146 10 false *a

Align the matchmarks and install the tripod joint assembly to the front drive outboard joint shaft assembly.

Text in Illustration
*a Matchmark

NOTICE:

Face the serrated side of the tripod joint assembly outward and install it to the front drive outboard joint shaft assembly end.



e.

Using a brass bar and hammer, install the tripod joint assembly.

NOTICE:
·

Do not tap the rollers.

·

Keep the tripod joint assembly free of foreign matter.




f.
C160822

Using a snap ring expander, install a new snap ring.


g.

Pack the front drive inboard joint assembly and front axle inboard joint boot with grease.

Standard Grease Capacity:
Drive Shaft Type Grease Capacity
Type A 112 to 122 g (4.0 to 4.3 oz.)
Type B 140 to 150 g (4.9 to 5.3 oz.)


HINT:
C306538E03
0.365,1.05 0.576,1.215 0.210,0.165 10 (A)

Measure the diameter (A) as shown in the illustration to determine the drive shaft type.


Diameter (A):
Drive Shaft Type Diameter
Type A 23.65 mm (0.931 in.)
Type B 24.10 mm (0.949 in.)



h.
C160821E11
0.918,0.354 1.095,0.531 0.177,0.177 10 *a 1.462,1.225 1.136,0.473 1.136,0.473 1.821,0.786 false

Align the matchmarks and install the front drive inboard joint assembly to the front drive outboard joint shaft assembly.

Text in Illustration
*a Matchmark


Hide 12.INSTALL FRONT AXLE INBOARD JOINT BOOT

a.

Install the front axle inboard joint boot to the grooves of the front drive inboard joint assembly and front drive outboard joint shaft assembly.

NOTICE:

Keep the grooves free of grease.



Hide 43448F 13.INSTALL FRONT AXLE INBOARD JOINT BOOT CLAMP

CAUTION:

Wear protective gloves to avoid injuries to your hands.


a.

for One Touch Type:

i.
C107948

Install a new front axle inboard joint boot clamp to the front axle inboard joint boot and provisionally fold back the lever.

NOTICE:
·

Set the lever into the guide groove correctly.

·

Check the band and lever for any deformation before folding back the lever.




ii.
C158356E20
2.479,0.948 2.677,1.146 0.198,0.198 10 false *a

Using water pump pliers, pinch the front axle inboard joint boot clamp to provisionally fix it.

Text in Illustration
*a Place the tip near the center of the lever.


iii.
C355422

Using a plastic hammer, tap the buckle to fix it while adjusting the clearance between the lever and groove to make the clearances between the buckle edge and lever end even.

NOTICE:

Do not damage the front axle inboard joint boot.




b.

for Claw Engagement Type:

i.
C157519

Using needle-nose pliers, engage the 2 claws and install a new front axle inboard joint boot clamp as shown in the illustration.

NOTICE:
·

Do not damage the front axle inboard joint boot.

·

Do not deform the claw of the hook.





Hide 43448G 14.INSTALL FRONT NO. 2 AXLE INBOARD JOINT BOOT CLAMP

CAUTION:

Wear protective gloves to avoid injuries to your hands.


a.

Install a new front No. 2 axle inboard joint boot clamp to the front axle inboard joint boot.


b.
C205466E01
1.445,1.547 1.655,1.712 0.210,0.165 10 (A)

Adjust dimension (A) until the front drive shaft assembly is within the specified length.

Dimension (A):
Drive Shaft Type LH RH
Type A 585.3 mm (1.92 ft.) 827.3 mm (2.71 ft.)
Type B 584.3 mm (1.92 ft.) 826.3 mm (2.71 ft.)


HINT:
C306538E04
0.365,1.05 0.576,1.215 0.210,0.165 10 (A)

Measure the diameter (A) as shown in the illustration to determine the drive shaft type.


Diameter (A):
Drive Shaft Type Diameter
Type A 23.65 mm (0.931 in.)
Type B 24.10 mm (0.949 in.)



c.

for One Touch Type:

i.
C415869C01
2.156,1.542 2.656,1.542 false 0.781,1.135 1.281,1.135 false 1.979,2.073 2.479,2.073 false 2.708,1.469 3.021,1.625 0.313,0.156 10 false *a 0.615,1.063 0.927,1.219 0.313,0.156 10 false *b 1.792,1.99 2.104,2.146 0.313,0.156 10 false *c
*a Fulcrum Point
*b Lever Push Position
*c Band Support Position


Temporarily fold back the lever at the fulcrum point.

NOTICE:
·

Check the band and the lever for any deformation before folding back the lever.

·

The lever folds easily at the fulcrum point when pushed at the position shown in the illustration.

·

When folding back the lever, do not push at the end of the lever.

C415873C01
6.771,1.49 6.125,1.49 true 5.948,1.417 6.26,1.573 0.313,0.156 10 false *a
*a Temporary Claw - -


·

If the lever bends in the middle, it may not engage with the temporary claws or may not be held in the correct position.




ii.

As shown in the illustration, while pressing the inboard joint area against the work surface, firmly press the lever into place by rolling the inboard joint area forward from the folded fulcrum point to the temporary claw area until a click sound is heard.

C415870C01
3.615,1.104 3.365,1.698 3.365,1.698 3.719,1.083 true 2.083,1.49 1.594,1.49 true 5.927,2.219 5.76,1.917 5.76,1.917 5.531,1.917 true 1.885,2.292 1.604,2.292 1.604,2.292 1.365,1.875 true 3.823,0.302 4.135,0.458 0.313,0.156 10 false *a 4.073,1.333 4.385,1.49 0.313,0.156 10 false *b 5.219,0.698 5.531,0.854 0.313,0.156 10 false *c 3.25,1.719 3.563,1.875 0.313,0.156 10 false *d 1.208,2.365 1.521,2.521 0.313,0.156 10 false *b 1.427,1.406 1.74,1.563 0.313,0.156 10 false *d 5.354,1.844 5.667,2 0.313,0.156 10 false *d 1.938,2.25 2.25,2.406 0.313,0.156 10 false *e
*a Press down *b Contact Point
*c Roll forward *d Temporary Claw
*e Fulcrum Point - -


NOTICE:
·

Make sure that the inboard joint is in direct contact with the work surface.

·

Do not damage the front drive shaft dust cover.




iii.
C158764C05
1.802,3.719 1.115,4.375 1.115,4.375 1.615,3.698 true 0.979,4.365 1.292,4.563 0.313,0.198 10 false *a
*a Buckle


Using a plastic hammer, tap the buckle to secure it while adjusting the clearance between the lever and the groove to make the clearance between the buckle edge and the lever end even.

NOTICE:
·

Do not use excessive force when tapping with the plastic hammer.

·

Do not damage the front axle inboard joint boot.





d.

for Claw Engagement Type:

i.
C157518

Using needle-nose pliers, engage the 2 claws and install a new front No. 2 axle inboard joint boot clamp as shown in the illustration.

NOTICE:
·

Do not damage the front axle inboard joint boot.

·

Do not deform the claw of the hook.