12363A
1.INSTALL ENGINE MOVING CONTROL ROD
Install the engine moving control rod with the bolt.
Temporarily tighten the transaxle side, and then tighten the bolt to the specified torque.
48069
2.TEMPORARILY TIGHTEN FRONT LOWER SUSPENSION ARM SUB-ASSEMBLY LH
Install the front lower suspension arm sub-assembly LH with the bolt.
48068
3.TEMPORARILY TIGHTEN FRONT LOWER SUSPENSION ARM SUB-ASSEMBLY RH
Use the same procedure for the RH side as for the LH side.
48811
4.INSTALL FRONT STABILIZER BAR
48829A
5.INSTALL FRONT NO. 1 STABILIZER BRACKET LH
48824A
6.INSTALL FRONT NO. 1 STABILIZER BRACKET RH
Use the same procedure for the RH side as for the LH side.
45510
7.INSTALL MANUAL STEERING GEAR
51201
8.INSTALL FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY
Place wooden blocks or plate lift attachments on an engine lifter, and then set the front suspension crossmember sub-assembly so that the attachments are in the positions shown in the illustration.
|
Front of the Vehicle |
|
Attachment Placement Positions |
Provisionally install the front suspension crossmember sub-assembly onto the body with the 6 bolts.
By inserting SST into the datum holes in the front suspension crossmembers RH and LH alternately, tighten bolts A, B and C on both sides to the specified torque, in several steps.
| *a | Datum Hole | - | - |
|
Front of the Vehicle | - | - |
Insert SST into the datum hole in a vertical orientation.
If SST cannot be inserted into the datum hole vertically, loosen all the bolts and then insert SST again.
Install the engine moving control rod with the bolt.
48069
9.INSTALL FRONT LOWER SUSPENSION ARM SUB-ASSEMBLY LH
48068
10.INSTALL FRONT LOWER SUSPENSION ARM SUB-ASSEMBLY RH
Use the same procedure for the RH side as for the LH side.
45047
11.INSTALL TIE ROD END SUB-ASSEMBLY LH
45046
12.INSTALL TIE ROD END SUB-ASSEMBLY RH
Use the same procedure for the RH side as for the LH side.
48810
13.INSTALL FRONT STABILIZER LINK ASSEMBLY LH
Install the front stabilizer link assembly LH with the nut.
Using a socket hexagon wrench 6 to hold the stud.
48820B
14.INSTALL FRONT STABILIZER LINK ASSEMBLY RH
Use the same procedure for the RH side as for the LH side.
45025D
15.INSTALL NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY
Install clip B onto the body portion and install the No. 1 steering column hole cover onto the body portion with clip A.
Make sure that the lip portion of steering column hole cover is not damaged.
45209
16.INSTALL STEERING SLIDING YOKE SUB-ASSEMBLY
Align the matchmarks and install the steering sliding yoke sub-assembly onto the manual steering gear.
| *1 | Steering Sliding Yoke Sub-assembly |
| *a | Matchmarks |
Install the bolt B.
Tighten bolt A.
45259A
17.INSTALL COLUMN HOLE COVER SILENCER SHEET
18.INSTALL FRONT WHEEL
19. POSITION WHEELS FACING STRAIGHT AHEAD
20. STABILIZE SUSPENSION
Lower the vehicle.
Bounce the vehicle up and down several times to stabilize the suspension.
48069
21.FULLY TIGHTEN FRONT LOWER SUSPENSION ARM SUB-ASSEMBLY LH
48068
22.FULLY TIGHTEN FRONT LOWER SUSPENSION ARM SUB-ASSEMBLY RH
Use the same procedure for the RH side as for the LH side.
51405A
23.INSTALL ENGINE UNDER COVER SUB-ASSEMBLY (for Metal Type)
24.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT
25. CHECK SPEED SENSOR SIGNAL (w/ ABS)
26. CHECK SPEED SENSOR SIGNAL (w/ VSC)