Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM
RM19S0E _54 Brake _051475 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0248226 ANTI-LOCK BRAKE SYSTEM D

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  DTC CHECK / CLEAR  


DTC CHECK/CLEAR (When Using Intelligent Tester)


a.

Check the DTC.

i.

Turn the ignition switch off.


ii.

Connect the intelligent tester to the DLC3.


iii.

Turn the ignition switch to ON.


iv.

Turn the tester on.


v.

Read the DTCs following the prompts on the tester screen. Enter the following menus: Chassis / ABS/VSC/TRC / DTC.


vi.

Check the details of the DTCs (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DIAGNOSTIC TROUBLE CODE CHART).

HINT:

Refer to the intelligent tester operator's manual for further details.




b.

Clear the DTC.

i.

Turn the ignition switch off.


ii.

Connect the intelligent tester to the DLC3.


iii.

Turn the ignition switch to ON.


iv.

Turn the tester on.


v.

Operate the intelligent tester to clear the codes. Enter the following menus: Chassis / ABS/VSC/TRC / DTC / Clear.


vi.

Clear the DTCs by following the prompts on the intelligent tester.

HINT:

Refer to the intelligent tester operator's manual for further details.





DTC CHECK/CLEAR (When not Using Intelligent Tester)


a.
U126760E01
0.108,0.087 0.413,0.237 0.304,0.151 10 *a 2.137,0.207 2.441,0.358 0.304,0.151 10 CG 1.157,1.943 1.461,2.094 0.304,0.151 10 TC

Check the DTC.

i.

Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.

SST
09843-18040  


ii.

Turn the ignition switch to ON.


iii.

Observe the blinking pattern of the ABS warning light in order to identify the DTC.

HINT:

If no code appears, inspect the TC and CG terminal circuit, and ABS warning light circuits.


Trouble Area See Procedure
TC and CG terminal circuit (Click here)
ABS warning light circuit (Remains on) (Click here)
ABS warning light circuit (Does not come on) (Click here)

Text in Illustration
*a Front view of DLC3

HINT:
·

When the system is operating correctly, each light will blink continuously in a pattern of 0.25 seconds on, and then 0.25 seconds off.

·

When one DTC is output, each light will output the same code at 4 second intervals (for example, code 21 would be output as 2 flashes, a 1.5 second pause, and then 1 flash).

·

When 2 or more DTCs are output, each light will output a different code at 2.5 second intervals, and when all codes have been output, there will be a 4 second pause and the sequence will repeat.

·

When multiple codes are stored, they are output in order starting with the lowest DTC number




iv.

Check the details of the DTCs.

ABS DTC
Warning Light Display Intelligent Tester Display
11 C146E
12 C146F
13 C146C
14 C146D
21 C1468
22 C1469
23 C146A
24 C146B
31 C1401
C1405
32 C1402
C1406
33 C1403
C1407
34 C1404
C1408
35 C1413
36 C1414
38 C1415
39 C1416
41 C1241
C1417
49 C1425
51 C1427
C1428
59 C1203
94 U0073
A2 U0142


v.

After completing the check, disconnect terminals TC and CG of the DLC3 to turn off the display.

HINT:

If 2 or more DTCs are detected at the same time, the DTCs will be displayed in ascending order.




b.

Clear the DTC.

i.
U126760E01
0.108,0.087 0.413,0.237 0.304,0.151 10 *a 2.137,0.207 2.441,0.358 0.304,0.151 10 CG 1.157,1.943 1.461,2.094 0.304,0.151 10 TC

Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.

SST
09843-18040  


ii.

Turn the ignition switch to ON.

Text in Illustration
*a Front view of DLC3


iii.

Clear the DTCs stored in the ECU by depressing the brake pedal 8 times or more within 5 seconds.


iv.

Check that the warning light indicates a normal system code.


v.

Remove SST from the terminals of the DLC3.

HINT:

Clearing the DTCs cannot be performed by disconnecting the battery terminal or the ECU-IG fuse.





END OF DTC CHECK/CLEAR


a.

Turn the ignition switch to ON.


b.

Check that the ABS warning light go off within approximately 3 seconds after turning the ignition switch to ON.