Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM › 2011.08–2017.01
RM19S0E _54 Brake _051475 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0248226 ANTI-LOCK BRAKE SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  TC and CG Terminal Circuit  


DESCRIPTION

Connecting terminals TC and CG of the DLC3 causes the ECU to display the DTC by blinking the ABS warning light.

WIRING DIAGRAM

C243297E02
0.931,2.033 1.292,2.195 0.360,0.162 10 ECM 0.63,2.033 0.902,2.174 0.271,0.141 10 A74 1.096,1.54 1.320,1.694 0.224,0.154 10 TC 1.401,1.449 1.590,1.590 0.189,0.141 10 27 5.334,1.491 7.063,1.879 1.729,0.388 10 Skid Control ECU (Brake Actuator Assembly) 5.396,2.564 5.585,2.714 0.189,0.149 10 13 5.454,2.947 5.550,3.085 0.096,0.138 10 4 5.65,2.653 5.857,2.798 0.207,0.145 10 TC 5.654,3.032 5.888,3.172 0.233,0.141 10 CG 5.703,3.588 5.897,3.746 0.194,0.158 10 F4 5.917,3.588 6.309,3.729 0.392,0.141 10 DLC3 1.196,4.361 2.863,4.517 1.667,0.156 10 : CAN Communication line

HINT:

When the warning lights continue to blink, a ground short in the wiring of terminal TC of the DLC3 or an internal ground short in one or more ECUs is suspected.


PROCEDURE

2.INSPECT DLC3
a.
U126756E01
0.129,0.087 0.434,0.237 0.304,0.151 10 *a 2.158,0.207 2.462,0.358 0.304,0.151 10 CG 1.178,1.943 1.482,2.094 0.304,0.151 10 TC 0.23,1.44 0.438,1.591 0.208,0.151 10 F4

Turn the ignition switch to ON.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F4-13 (TC) - F4-4 (CG) Ignition switch ON 11 to 14 V



Result
Result Proceed to
NG A
OK B

Text in Illustration
*a Front view of DLC3


A

3.CHECK HARNESS AND CONNECTOR (TC of DLC3 - ECM)

B

5.INSPECT ECM (TC of DLC3 INPUT)
3.CHECK HARNESS AND CONNECTOR (TC of DLC3 - ECM)
a.

Turn the ignition switch off.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F4-13 (TC) - A74-27 (TC) Always Below 1 Ω
F4-13 (TC) - Body ground Always 10 kΩ or higher



d.

Reconnect the ECM connector.



OK

4.CHECK HARNESS AND CONNECTOR (CG of DLC3 - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (CG of DLC3 - BODY GROUND)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F4-4 (CG) - Body ground Always Below 1 Ω




OK

5.INSPECT ECM (TC of DLC3 INPUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT ECM (TC of DLC3 INPUT)
a.
U126757E01
0.129,0.087 0.434,0.237 0.304,0.151 10 *a 2.158,0.207 2.462,0.358 0.304,0.151 10 CG 1.178,1.943 1.482,2.094 0.304,0.151 10 TC 0.238,1.44 0.418,1.591 0.180,0.151 10 F4

Turn the ignition switch off.


b.

Using SST, connect terminals TC and CG of the DLC3.


c.

Turn the ignition switch to ON.


d.

Check that the malfunction indicator lamp is blinking.


Text in Illustration
*a Front view of DLC3

Result
Result Proceed to
Malfunction indicator lamp is blinking A
Malfunction indicator lamp is not blinking (for LHD) B
Malfunction indicator lamp is not blinking (for RHD) C


A

REPAIR OR REPLACE WIRE HARNESS OR ECM (TC of ECM CIRCUIT)

B

C