Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM
RM19S0E _54 Brake _051475 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0248226 ANTI-LOCK BRAKE SYSTEM D

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  FREEZE FRAME DATA  


FREEZE FRAME DATA


a.

Whenever a DTC is detected, the skid control ECU (brake actuator assembly) stores the current vehicle (sensor) state as Freeze Frame Data.


b.

The skid control ECU (brake actuator assembly) stores the number of times (maximum: 31) the ignition switch has been turned from off to ON since the last time the ABS was activated.

HINT:
·

However, if the vehicle is stopped or at a low speed (7 km/h (4.3 mph) or less), or if a DTC is detected, the skid control ECU (brake actuator assembly) will stop counting the number.

·

Freeze Frame Data at the time the ABS operates:

The skid control ECU (brake actuator assembly) stores and updates data whenever the ABS system operates.

When the ECU stores data at the time a DTC is detected, the data stored during ABS operation is cleared.

·

Freeze Frame Data at the time a DTC is detected:

When the skid control ECU (brake actuator assembly) stores data at the time a DTC is detected, no updates will be performed until the data is cleared.





CHECK FREEZE FRAME DATA


a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Check the freeze frame data by following the prompts on the intelligent tester display.

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Elapsed Time after Freeze Trigger Elapsed time after freeze trigger/Min.: 0 msec, Max.: 500 msec - -
Number of IG ON Number of operations of ignition switch being turned to ON after storing Freeze Frame Data/0 to 31 - -
Stop Light SW Stop light switch/OFF or ON OFF: Brake pedal released
ON: Brake pedal depressed
-
Parking Brake SW Parking brake switch/OFF or ON OFF: Parking brake released
ON: Parking brake applied
-
Operated System Operated system status/Non, ABS, VSC, TRC, BA, HAB, Fail, PBA, PB, HA-CTRL, Sys Non: No operation activated
ABS: ABS activated
Fail: Fail safe mode activated
Sys: System prohibit activated
-
Forward and Rearward G Forward and backward G/Min.: -25.10 m/s2, Max.: 24.90 m/s2 - During acceleration/deceleration:
Changes in proportion with acceleration
FR Wheel Speed FR wheel speed sensor reading/Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) 0 km/h: Vehicle stopped When driving at constant speed:
No large fluctuations
FL Wheel Speed FL wheel speed sensor reading/Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) 0 km/h: Vehicle stopped When driving at constant speed:
No large fluctuations
RR Wheel Speed RR wheel speed sensor reading/Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) 0 km/h: Vehicle stopped When driving at constant speed:
No large fluctuations
RL Wheel Speed RL wheel speed sensor reading/Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) 0 km/h: Vehicle stopped When driving at constant speed:
No large fluctuations
Vehicle Speed Maximum wheel speed sensor reading/Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Actual vehicle speed Speed indicated on speedometer
Vehicle Speed Grade Vehicle speed grade/Min.: -25.10 m/s2, Max.: 24.90 m/s2 0 m/s2: Vehicle stopped During driving: Changes in proportion with vehicle acceleration/deceleration



CLEAR FREEZE FRAME DATA


NOTICE:

Clearing the DTC will also clear the Freeze Frame Data.


a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.