Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM(for Built-in Type Yaw Rate Sensor)
RM19S0E _54 Brake _051475 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0248227 VEHICLE STABILITY CONTROL SYSTEM(for Built-in Type Yaw Rate Sensor) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM(for Built-in Type Yaw Rate Sensor)  C1241  Low Power Supply Voltage Malfunction  


DESCRIPTION

If a malfunction is detected in the power supply circuit, the skid control ECU (brake actuator assembly) stores this DTC and the fail-safe function prohibits ABS operation.

This DTC is stored when the IG1 terminal voltage deviates from the DTC detection condition due to a malfunction in the power supply or charging circuit such as the battery or generator circuit, etc.

The DTC is cancelled when the IG1 terminal voltage returns to normal.

DTC No. DTC Detection Condition Trouble Area
C1241 When any of the following is detected:
1.

At a vehicle speed of 3 km/h (2 mph) or more, the IG1 terminal voltage is less than 9.5 V for 10 seconds or more.

2.

When the solenoid relay remains ON and the IG1 terminal voltage is less than 9.5 V, the relay contact is open for 0.22 seconds or more.

3.

With the IG1 terminal voltage 9.5 V or less, the vehicle speed sensor power supply decreases for 60 seconds or more.

4.

When the motor fail safe relay is ON after the motor relay turns ON, the IG1 terminal voltage is 9.5 V or less and the actuator pump drive motor is OFF for 0.22 seconds or more.


·

ECU-IG NO. 2 fuse

·

Battery

·

Charging system

·

Power source circuit

·

Internal power supply circuit of the skid control ECU



WIRING DIAGRAM

C243288E01
1.786,0.854 2.737,1.027 0.951,0.174 10 ECU-IG NO. 2 4.075,0.626 4.255,0.787 0.180,0.161 10 34 4.337,0.738 4.594,0.878 0.258,0.140 10 IG1 4.101,1.242 4.199,1.404 0.098,0.161 10 1 4.337,1.355 5.004,1.495 0.667,0.140 10 GND1 3.819,1.734 4.111,1.883 0.291,0.149 10 A54 3.819,1.899 6.655,2.073 2.836,0.174 10 Skid Control ECU (Brake Actuator Assembly)

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the brake actuator assembly, perform zero point calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Built-in Type Yaw Rate Sensor)>CALIBRATION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.INSPECT BATTERY
a.

Check the battery voltage.

Standard voltage:

11 to 14 V


Result
Result Proceed to
OK A
NG (for 1NZ-FE) B
NG (for 2NZ-FE) C



A

2.CHECK TERMINAL VOLTAGE (IG1 TERMINAL)

B

C

2.CHECK TERMINAL VOLTAGE (IG1 TERMINAL)
a.

Disconnect the skid control ECU (brake actuator assembly) connector.


b.

Turn the ignition switch to ON.


c.
U158451E01
0.044,0.021 0.243,0.183 0.199,0.162 10 *a 1.589,0.159 1.872,0.307 0.284,0.149 10 A54 1.932,1.836 2.196,1.984 0.263,0.149 10 IG1 2.219,1.377 2.06,1.825 false

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A54-34 (IG1) - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Skid control ECU)


d.

Turn the ignition switch off.



OK

3.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (IG1 CIRCUIT)

3.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)
a.
U158452E01
0.044,0.021 0.243,0.183 0.199,0.162 10 *a 1.589,0.159 1.872,0.307 0.284,0.149 10 A54 0.434,1.911 0.867,2.059 0.433,0.149 10 GND1 1.055,1.015 0.678,1.871 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A54-1 (GND1) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Skid control ECU)


b.

Reconnect the skid control ECU (brake actuator assembly) connector.



OK

4.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND1 CIRCUIT)

4.RECONFIRM DTC

b.

Start the engine.


c.

Drive the vehicle at a speed of 20 km/h (12 mph) or more for 30 seconds or more.



Result
Result Proceed to
DTC is not output A
DTC is output B

HINT:

If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Built-in Type Yaw Rate Sensor)>PROBLEM SYMPTOMS TABLE).



A

B