Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › BRAKE ACTUATOR (for RHD)
RM19S0E _54 Brake _051475 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0248229 BRAKE ACTUATOR(for RHD) A

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  BRAKE ACTUATOR(for RHD)  REMOVAL  


PROCEDURE

Hide 1.DRAIN BRAKE FLUID

NOTICE:

Immediately wash off any brake fluid that comes into contact with any painted surfaces.


Hide 74431 3.REMOVE BATTERY TRAY

Hide 44510 5.REMOVE BRAKE ACTUATOR ASSEMBLY (w/o VSC)

a.
C228099E03
2.156,1.427 2.396,1.365 false 1.99,1.354 2.156,1.583 0.167,0.229 10 false *1

Release the lock lever and disconnect the brake actuator connector.

Text in Illustration
*1 Lock lever

NOTICE:

Be careful not to allow brake fluid to enter the removed connector.



b.
C420067C01
1.604,0.698 2.135,0.302 2.135,0.302 2.24,0.302 true 0.729,0.24 0.802,0.24 0.802,0.24 1.24,0.604 true 0.25,1.083 0.354,1.083 0.354,1.083 1.448,0.958 true 0.354,0.667 0.458,0.667 0.458,0.667 1.042,0.792 true 1.74,0.781 2.198,0.552 2.198,0.552 2.302,0.552 true 1.438,0.646 1.813,0.188 1.813,0.188 1.917,0.188 true 0.188,0.594 0.375,0.771 0.188,0.177 10 true *a 0.063,1 0.26,1.198 0.198,0.198 10 true *b 2.344,0.469 2.563,0.667 0.219,0.198 10 true *c 2.281,0.219 2.479,0.417 0.198,0.198 10 true *d 1.958,0.115 2.135,0.281 0.177,0.167 10 true *e 0.542,0.177 0.74,0.375 0.198,0.198 10 true *f
*a From 1st Chamber of Brake Master Cylinder Sub-assembly
*b From 2nd Chamber of Brake Master Cylinder Sub-assembly
*c To Front Wheel Cylinder Assembly LH
*d To Rear Wheel Cylinder Assembly RH
*e To Rear Wheel Cylinder Assembly LH
*f To Front Wheel Cylinder Assembly RH


Use tags or make a memo to identify the places to reconnect the brake tubes.


c.
C232052

Using a union nut wrench 10 mm, separate the 6 brake tubes from the brake actuator assembly.


d.
C169912

Remove the 3 bolts and brake actuator with bracket.

NOTICE:

Do not damage the brake tubes or wire harness.



Hide 44510 6.REMOVE BRAKE ACTUATOR ASSEMBLY (w/ VSC)

a.
C228099E03
2.156,1.427 2.396,1.365 false 1.99,1.354 2.156,1.583 0.167,0.229 10 false *1

Release the lock lever and disconnect the brake actuator connector.

Text in Illustration
*1 Lock lever

NOTICE:

Be careful not to allow brake fluid to enter the removed connector.



b.
C420068C01
1.594,0.594 2.135,0.302 2.135,0.302 2.24,0.302 true 0.729,0.24 0.802,0.24 0.802,0.24 1.156,0.49 true 0.229,0.969 0.333,0.969 0.333,0.969 1.469,0.896 true 0.354,0.667 0.458,0.667 0.458,0.667 0.99,0.76 true 1.76,0.635 2.198,0.552 2.198,0.552 2.302,0.552 true 1.417,0.542 1.813,0.188 1.813,0.188 1.917,0.188 true 0.188,0.594 0.375,0.771 0.188,0.177 10 true *a 0.063,0.896 0.26,1.094 0.198,0.198 10 true *b 2.344,0.469 2.563,0.667 0.219,0.198 10 true *c 2.281,0.219 2.479,0.417 0.198,0.198 10 true *d 1.958,0.115 2.135,0.281 0.177,0.167 10 true *e 0.542,0.177 0.74,0.375 0.198,0.198 10 true *f
*a From 1st Chamber of Brake Master Cylinder Sub-assembly
*b From 2nd Chamber of Brake Master Cylinder Sub-assembly
*c To Front Wheel Cylinder Assembly LH
*d To Rear Wheel Cylinder Assembly RH
*e To Rear Wheel Cylinder Assembly LH
*f To Front Wheel Cylinder Assembly RH


Use tags or make a memo to identify the places to reconnect the brake tubes.


c.
C232505

Using a union nut wrench 10 mm and union nut wrench 12 mm, separate the 6 brake tubes from the brake actuator assembly.

Text in Illustration
V100135

Flare Nut 10 mm
V100136

Flare Nut 12 mm


d.
C228794

Remove the 3 bolts and brake actuator with bracket.

NOTICE:

Do not damage the brake tubes or wire harness.



Hide 44590 7.REMOVE BRAKE ACTUATOR BRACKET ASSEMBLY

a.
C228795

Remove the 3 bolts and brake actuator bracket assembly.


Hide 44546A 8.REMOVE BRAKE ACTUATOR BOLT CUSHION

a.

Remove the 3 brake actuator case collars from the brake actuator bolt cushion.


b.

Remove the 3 brake actuator bolt cushions from the brake actuator bracket assembly.