Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM(for Built-in Type Yaw Rate Sensor) › 2011.08–2017.01
RM19S0E _54 Brake _051475 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0248227 VEHICLE STABILITY CONTROL SYSTEM(for Built-in Type Yaw Rate Sensor) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM(for Built-in Type Yaw Rate Sensor)  C1232  Acceleration Sensor Stuck Malfunction  C1243  Acceleration Sensor Stuck Malfunction  C1245  Acceleration Sensor Output Malfunction  C1279  Acceleration Sensor Output Voltage Malfunction (Test Mode DTC)  C1473  Yaw Rate Sensor (Test Mode DTC)  


DESCRIPTION

The skid control ECU (brake actuator assembly) receives signals from the yaw rate and deceleration sensor (airbag sensor assembly) via the CAN communication system.

The yaw rate and deceleration sensor (airbag sensor assembly) has a built in deceleration sensor and detects the vehicle's condition using 2 circuits (GL1, GL2).

If there is trouble in the bus lines between the yaw rate and deceleration sensor (airbag sensor assembly) and the CAN communication system, the DTC U0124 (malfunction in CAN communication with the acceleration sensor) is output.

These DTCs are also output when calibration has not been completed.

DTCs C1279 and C1473 can be cleared when the yaw rate and deceleration sensor (airbag sensor assembly) sends a yaw rate and/or deceleration signal or the Test Mode ends. DTCs C1279 and C1473 are output only in the Test Mode.

DTC No. DTC Detection Condition Trouble Area
C1232 At a vehicle speed of 10 km/h (6 mph) or more, either GL1 or GL2 (input signal) does not change for 30 seconds or more.
·

Yaw rate and deceleration sensor (Airbag sensor assembly)

·

Yaw rate and deceleration sensor (Airbag sensor assembly) circuit


C1243 While the vehicle speed changes from 30 km/h (19 mph) to 0 km/h (0 mph), the condition that the values of GL1 and GL2 do not change 0.0294 G or more occurs 16 times or more.
·

Yaw rate and deceleration sensor (Airbag sensor assembly)

·

Yaw rate and deceleration sensor (Airbag sensor assembly) circuit


C1245 At a vehicle speed of 30 km/h (19 mph) or more, the difference between the forward and backward G calculated from the acceleration sensor value and that calculated from the vehicle speed exceeds 0.35 G for 60 seconds or more.
·

Yaw rate and deceleration sensor (Airbag sensor assembly)

·

Yaw rate and deceleration sensor (Airbag sensor assembly) circuit

·

Sensor installation


C1279 Detected only during Test Mode.
·

Yaw rate and deceleration sensor (Airbag sensor assembly)

·

Sensor installation


C1473 Detected only during Test Mode. Yaw rate and deceleration sensor (Airbag sensor assembly)

WIRING DIAGRAM

C240027E04
5.227,3.324 6.902,3.638 1.675,0.314 10 Skid Control ECU (Brake Actuator Assembly) 0.72,4.166 2.395,4.338 1.675,0.172 10 : CAN Communication line 2.824,1.901 3.094,2.060 0.271,0.159 10 IG2 0.961,1.748 1.231,1.907 0.271,0.159 10 IG2 1.276,1.632 1.457,1.789 0.181,0.156 10 21 1.276,2.591 1.457,2.747 0.181,0.156 10 26 1.276,2.213 1.457,2.369 0.181,0.156 10 25 1.001,2.693 1.204,2.853 0.203,0.159 10 E2 1.001,2.329 1.204,2.488 0.203,0.159 10 E1 0.024,3.375 2.213,3.702 2.189,0.326 10 Yaw Rate and Deceleration Sensor (Airbag Sensor Assembly) 0.024,3.198 0.295,3.375 0.271,0.178 10 F16

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the brake actuator assembly, perform zero point calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Built-in Type Yaw Rate Sensor)>CALIBRATION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



HINT:

When U0124 and/or U0126 is output together with C1232, C1243 and/or C1245, inspect and repair the trouble areas indicated by U0124 and/or U0126 first (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Built-in Type Yaw Rate Sensor)>U0073).


PROCEDURE

1.CHECK DTC

b.

At a speed of 30 km/h (19 mph) or more, drive the vehicle, turn the steering wheel, and decelerate (depress the brake pedal) the vehicle.



d.

Check if DTCs for zero point calibration of the yaw rate sensor undone (C1210) or for zero point calibration of the deceleration sensor undone (C1336) are output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Built-in Type Yaw Rate Sensor)>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC (relating to yaw rate and deceleration sensor) is output A
DTC (relating to CAN communication system) is output B
DTC (C1210 and/or C1336) are output C



A

2.CHECK YAW RATE AND DECELERATION SENSOR (AIRBAG SENSOR ASSEMBLY) INSTALLATION

B

C

2.CHECK YAW RATE AND DECELERATION SENSOR (AIRBAG SENSOR ASSEMBLY) INSTALLATION
a.

Turn the ignition switch off.


b.

Check that the yaw rate and deceleration sensor (airbag sensor assembly) has been installed properly (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CENTER AIRBAG SENSOR ASSEMBLY>INSTALLATION).

OK:

The sensor should be tightened to the specified torque.

The sensor should not be tilted.




OK

REPLACE YAW RATE AND DECELERATION SENSOR (AIRBAG SENSOR ASSEMBLY)

NG

INSTALL YAW RATE AND DECELERATION SENSOR (AIRBAG SENSOR ASSEMBLY) CORRECTLY