Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM(for Built-in Type Yaw Rate Sensor)
RM19S0E _54 Brake _051475 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0248227 VEHICLE STABILITY CONTROL SYSTEM(for Built-in Type Yaw Rate Sensor) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM(for Built-in Type Yaw Rate Sensor)  C1381  Acceleration Sensor Power Supply Voltage Malfunction  


DESCRIPTION

The skid control ECU (brake actuator assembly) receives signals from the yaw rate and deceleration sensor (airbag sensor assembly) via the CAN communication system.

The yaw rate and deceleration sensor (airbag sensor assembly) has a built in deceleration sensor and detects the vehicle's condition using 2 circuits (GL1, GL2).

If there is trouble in the bus lines between the yaw rate and deceleration sensor (airbag sensor assembly) and the CAN communication system, the DTC U0124 (Lost Communication with Lateral Acceleration Sensor Module) is output.

These DTCs are also output when calibration has not been completed.

DTC No. DTC Detection Condition Trouble Area
C1381 At a vehicle speed of more than 3 km/h (2 mph), the acceleration sensor power source malfunction signal is received for 10 seconds or more.
·

Yaw rate and deceleration sensor (Airbag sensor assembly)

·

Yaw rate and deceleration sensor (Airbag sensor assembly) power source circuit



CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the brake actuator assembly, perform zero point calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Built-in Type Yaw Rate Sensor)>CALIBRATION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK TERMINAL VOLTAGE (IG2 TERMINAL)
a.
U158349E02
1.125,1.49 0.563,1.49 true 0.281,1.406 0.531,1.583 0.25,0.177 10 false IG2 0.146,0.125 0.333,0.281 0.188,0.156 10 false *a 1.635,0.385 1.927,0.563 0.292,0.177 10 false F16

Disconnect the yaw rate and deceleration sensor (airbag sensor assembly) connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F16-21 (IG2) - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Yaw Rate and Deceleration Sensor (Airbag Sensor Assembly))


d.

Turn the ignition switch off.



OK

2.CHECK HARNESS AND CONNECTOR (GND TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (IG CIRCUIT)

2.CHECK HARNESS AND CONNECTOR (GND TERMINAL)
a.
U126939E02
1.813,1.542 2.125,1.844 true 1.688,1.542 1.375,1.844 true 1.229,1.854 1.427,2.031 0.198,0.177 10 false E1 2.063,1.865 2.26,2.042 0.198,0.177 10 false E2 0.146,0.073 0.333,0.229 0.188,0.156 10 false *a 1.625,0.385 1.917,0.542 0.292,0.156 10 false F16

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F16-25 (E1) - Body ground Always Below 1 Ω
F16-26 (E2) - Body ground Always Below 1 Ω


NOTICE:

Check the yaw rate and deceleration sensor (airbag sensor assembly) signal after replacement (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Built-in Type Yaw Rate Sensor)>TEST MODE PROCEDURE).


HINT:

If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Built-in Type Yaw Rate Sensor)>PROBLEM SYMPTOMS TABLE).



Text in Illustration
*a Front view of wire harness connector
(to Yaw Rate and Deceleration Sensor (Airbag Sensor Assembly))

b.

Reconnect the yaw rate and deceleration sensor (airbag sensor assembly) connector.



OK

3.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND CIRCUIT)

3.RECONFIRM DTC

b.

Start the engine.


c.

Perform a road test.



Result
Result Proceed to
DTC C1381 is not output A
DTC C1381 is output B


A

B

REPLACE YAW RATE AND DECELERATION SENSOR (AIRBAG SENSOR ASSEMBLY)