Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM(for Built-in Type Yaw Rate Sensor)
RM19S0E _54 Brake _051475 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0248227 VEHICLE STABILITY CONTROL SYSTEM(for Built-in Type Yaw Rate Sensor) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM(for Built-in Type Yaw Rate Sensor)  C1281  Master Cylinder Pressure Sensor Output Malfunction (Test Mode DTC)  C1421  Open or Short in Master Cylinder Pressure Sensor  C1423  Master Cylinder Pressure Sensor Zero Point Low Malfunction  C1424  Master Cylinder Pressure Sensor Output Malfunction  


DESCRIPTION

The master cylinder pressure sensor is connected to the skid control ECU.

C234442E10
3.76,3.677 5.385,3.885 1.625,0.208 10 false Brake Actuator Assembly 0.24,1.813 1.677,2.167 1.438,0.354 10 false from Stop Light Switch 2.823,1.823 3.271,2.031 0.448,0.208 10 false STP 3.854,1.5 4.323,1.708 0.469,0.208 10 false VCM 3.885,2.177 4.333,2.385 0.448,0.208 10 false PMC 3.979,2.906 4.292,3.125 0.313,0.219 10 false E2 0.229,4.073 3.885,4.281 3.656,0.208 10 false VCM: Power Supply for Master Cylinder Pressure Sensor 0.229,4.469 3.156,4.677 2.927,0.208 10 false PMC: Master Cylinder Pressure Sensor Input 0.365,4.833 3.302,5.229 2.938,0.396 10 false E2: Master Cylinder Pressure Sensor Ground 2.979,0.813 4.115,1 1.135,0.188 10 false Skid Control ECU 5.729,1.75 6.313,2.406 0.583,0.656 10 false Master Cylinder Pressure Sensor

DTC No. DTC Detection Condition Trouble Area
C1421 Either of the following is detected:
1.

With the IG1 terminal voltage between 9.5 and 17.4 V, the VCM terminal voltage is not between 4.4 and 5.6 V for 1.2 seconds or more.

2.

When the VCM terminal voltage is between 4.8 and 5.2 V, the PMC terminal voltage is not between 0.19 and 4.57 V for 1.2 seconds or more.


Brake actuator assembly (Master cylinder pressure sensor)
C1423 The PMC terminal voltage is less than 0.27 V for 5 seconds or more. Brake actuator assembly (Master cylinder pressure sensor)
C1424 Any of the following is detected:
1.

Noise occurs in the PMC terminal 7 times or more within 5 seconds.

2.

When the vehicle speed drops from 40 km/h (25 mph) to 10 km/h (6 mph), the master cylinder pressure does not change by at least 0.048 MPa.

3.

At a vehicle speed of 7 km/h (4.3 mph) or more, the PMC terminal voltage is between 0.86 and 1.0 V and does not change by at least 0.048 MPa for 60 seconds or more.

4.

At a vehicle speed of 7 km/h (4.3 mph) or more, the PMC terminal voltage is 1.0 V or more and does not change by at least 0.048 MPa for 30 seconds or more.

5.

At a vehicle speed of 7 km/h (4.3 mph) or more with the stop switch ON, a state in which the pressure sensor input value is sufficiently greater than the estimated master pressure continues for 1 second or more and this state occurs 5 or more times each time the ignition switch is turned to ON, and this occurs 8 or more times consecutively.


Brake actuator assembly (Master cylinder pressure sensor)

Test Mode Diagnosis Code
DTC No. DTC Detection Condition Trouble Area
C1281 Detected only during Test Mode. Brake actuator assembly (Master cylinder pressure sensor)

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the brake actuator assembly (skid control ECU), perform zero point calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Built-in Type Yaw Rate Sensor)>CALIBRATION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.REPLACE BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU)
a.

Replace the brake actuator assembly (master cylinder pressure sensor (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for RHD)>REMOVAL)).



NEXT

END