Home › Engine / Hybrid System › 2NZ-FE ENGINE MECHANICAL › ENGINE ASSEMBLY › 2011.08–2014.07
RM19S0E _51 Engine / Hybrid System _051451 2NZ-FE ENGINE MECHANICAL _0248090 ENGINE ASSEMBLY A

2NZ-FE ENGINE MECHANICAL  ENGINE ASSEMBLY  REMOVAL  


PROCEDURE

Hide 1.DISCHARGE FUEL SYSTEM PRESSURE

Hide 2.REMOVE FRONT WHEELS

Hide 51442C 3.REMOVE ENGINE UNDER COVER LH (for Plastic Type)

Hide 51441C 4.REMOVE ENGINE UNDER COVER RH (for Plastic Type)

Hide 5.REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY (for Metal Type)

Hide 7.DRAIN AUTOMATIC TRANSAXLE FLUID (for Automatic Transaxle)

Hide 8.DRAIN MANUAL TRANSAXLE OIL (for Manual Transaxle)

Hide 9.REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Hide 55815E 10.REMOVE FRONT NO. 1 VENTILATOR SEAL (for LHD)

Hide 55815E 11.REMOVE FRONT NO. 1 VENTILATOR SEAL (for RHD)

Hide 55735D 12.REMOVE FRONT AIR SHUTTER SEAL RH (for LHD)

Hide 55735D 13.REMOVE FRONT AIR SHUTTER SEAL RH (for RHD)

Hide 55722C 14.REMOVE INNER COWL TOP TO COWL BRACE (for LHD)

Hide 55722C 15.REMOVE INNER COWL TOP TO COWL BRACE (for RHD)

Hide 55711 16.REMOVE OUTER COWL TOP PANEL (for LHD)

Hide 55711 17.REMOVE OUTER COWL TOP PANEL (for RHD)

Hide 28800 18.REMOVE BATTERY

A248909

a.

Disconnect the cable from the battery terminal.


b.

Loosen the 2 nuts and remove the battery clamp.


c.

Remove the battery.


Hide 74431 19.REMOVE BATTERY TRAY

Hide 17700 21.REMOVE AIR CLEANER ASSEMBLY

a.
A249575

Disengage the clamp and disconnect the fuel vapor feed hose assembly from the No. 1 air cleaner hose.


b.

Loosen the 2 hose clamps and disconnect the fuel vapor feed hose assembly from the No. 1 air cleaner hose and vacuum switching valve assembly.


c.
A249576

Disconnect the No. 2 fuel vapor feed hose from the intake manifold.


d.
A249577

Disengage the 2 clamps and disconnect the wire harness from the air cleaner cap sub-assembly and vacuum switching valve assembly.


e.

Disconnect the mass air flow meter connector.


f.

Disconnect the vacuum switching valve connector.


g.
A249578

Loosen the hose clamp and disconnect the No. 1 air cleaner hose from the throttle with motor body assembly.


h.

Disengage the 2 clamps and remove the air cleaner cap sub-assembly with No. 1 air cleaner hose.


i.
A246503

Remove the air cleaner element.


j.
A249653

Disengage the clamp and disconnect the wire harness from the air cleaner case.


k.

Remove the 2 bolts and the air cleaner case from the air cleaner bracket.


Hide 17771A 22.REMOVE AIR CLEANER BRACKET

A381783

a.

Disengage the clamp and disconnect the wire harness from the air cleaner bracket.


b.

Remove the 2 bolts and the air cleaner bracket.


Hide 74411 23.REMOVE BATTERY CARRIER (for LHD)

A259809

a.

Disengage the 6 wire harness clamps and separate the wire harness from the battery carrier.


b.

Remove the 5 bolts and the battery carrier.


Hide 74411 24.REMOVE BATTERY CARRIER (for RHD)

A247997

a.

Disengage the 7 wire harness clamps and separate the wire harness from the battery carrier.


b.

Remove the 5 bolts and the battery carrier.


Hide 23820 25.REMOVE FUEL VAPOR FEED HOSE ASSEMBLY

A249654

a.

Loosen the 2 hose clamps and remove the fuel vapor feed hose assembly.


Hide 26.DISCONNECT RADIATOR RESERVOIR TANK HOSE

A246505

a.

Disconnect the radiator reservoir tank hose from the water filler.


Hide 16573B 27.DISCONNECT NO. 3 RADIATOR HOSE

A246723

a.

Loosen the hose clamp and disconnect No. 3 radiator hose from the water filler.


Hide 16572D 28.DISCONNECT NO. 2 RADIATOR HOSE

A104893

a.

Loosen the hose clamp and disconnect No. 2 radiator hose from the water inlet.


Hide 23842A 29.REMOVE EFI FUEL PIPE CLAMP

A149873

a.

Remove the fuel pipe clamp.


Hide 23901 30.DISCONNECT FUEL TUBE SUB-ASSEMBLY

a.
A250097E03
1.573,0.677 0.896,0.969 false 0.698,0.917 0.865,1.115 0.167,0.198 10 true *1

Pinch the retainer as illustrated, then pull the fuel tube connector out of the pipe.

Text in Illustration
*1 Retainer
V100135

Pinch
V100136

Pull

NOTICE:
·

Remove any dirt and foreign matter from the fuel tube connector before performing this work.

·

Do not allow any scratches or foreign matter on the parts when disconnecting, as the fuel tube connector has the O-rings that seal the pipe.

·

Perform this work by hand. Do not use any tools.

·

Do not forcibly bend, twist or turn the nylon tube.

·

Protect the disconnected parts by covering them with vinyl bags after disconnecting the fuel tube.

·

If the fuel tube connector and pipe are stuck, push and pull to release them.




Hide 31.DISCONNECT INLET OIL COOLER HOSE (for Automatic Transaxle)

A117306

a.

Loosen the clip and disconnect the oil cooler outlet hose.


Hide 32.DISCONNECT OUTLET OIL COOLER HOSE (for Automatic Transaxle)

A117307

a.

Loosen the clip and disconnect the oil cooler inlet hose.


Hide 44773F 33.DISCONNECT UNION TO CHECK VALVE HOSE

A246727

a.

Loosen the hose clamp and disconnect the union to check valve hose from the booster vacuum tube.


Hide 87246A 34.DISCONNECT OUTLET HEATER WATER HOSE A

A246728

a.

Loosen the hose clamp and disconnect outlet heater water hose A from the heater unit.


Hide 87245A 35.DISCONNECT INLET HEATER WATER HOSE A

A246729

a.

Loosen the hose clamp and disconnect inlet heater water hose A from the heater unit.


Hide 16361A 36.REMOVE FAN AND GENERATOR V BELT

Hide 31470 37.SEPARATE CLUTCH RELEASE CYLINDER ASSEMBLY (for Manual Transaxle)

Hide 88310 38.SEPARATE COMPRESSOR WITH PULLEY ASSEMBLY (w/ Air Conditioning System)

A249659

a.

Disconnect the connector.


b.

Remove the 4 bolts and separate the with pulley compressor assembly.

HINT:

Remove the compressor assembly together with the low and high pressure hoses, then suspend them from the body with a piece of rope.



Hide 39.DISCONNECT ENGINE WIRE

a.

for Automatic Transaxle:

i.
A248925

Disengage the clamp and disconnect the wire harness from the automatic transaxle.


ii.

Remove the bolt and separate the wire harness from the automatic transaxle.



b.
A235042

Disengage the wire harness clamp and separate the wire harness.


c.

Pull up the lever and disconnect the connector of the engine control computer.


d.
A249656

Disengage the clamp and disconnect the wire harness.


e.

Disconnect the 2 connectors.


f.
A249657

Disengage the 2 claws and disconnect the wire harness from the engine room relay block.


g.
A248920

Disconnect the 2 connectors from the battery positive terminal.


h.

Disconnect all the wire harnesses and connectors. Make sure that no wire harness is connected between the body and engine.


Hide 58910C 40.REMOVE REAR CONSOLE BOX ASSEMBLY

Hide 57533B 41.REMOVE FRONT FLOOR CENTER BRACE (w/ Side Mudguard)

Hide 17451 43.REMOVE EXHAUST PIPE GASKET

Hide 17451A 44.REMOVE NO. 2 EXHAUST PIPE GASKET

Hide 33820B 45.SEPARATE TRANSMISSION CONTROL CABLE ASSEMBLY (for Automatic Transaxle)

Hide 33820B 46.SEPARATE TRANSMISSION CONTROL CABLE ASSEMBLY (for Manual Transaxle)

Hide 43420 47.REMOVE FRONT DRIVE SHAFT ASSEMBLY

Hide 11361J 48.REMOVE FLYWHEEL HOUSING UNDER COVER (for Automatic Transaxle)

a.
C156192

Remove the flywheel housing cover.


Hide 32101G 49.REMOVE TORQUE CONVERTER SETTING BOLT (for Automatic Transaxle)

A107285E07
1.698,1.823 2.083,1.823 true 2.135,1.75 2.583,1.969 0.448,0.219 10 true SST

a.

Hold the crankshaft with SST.

SST
09960-10010  (09962-01000, 09963-01000)


b.
A117323

Remove the 6 torque converter set bolts.


Hide 45259A 50.REMOVE COLUMN HOLE COVER SILENCER SHEET

Hide 45209 51.SEPARATE STEERING SLIDING YOKE SUB-ASSEMBLY

Hide 45025D 52.REMOVE NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY

Hide 53.REMOVE ENGINE ASSEMBLY WITH TRANSAXLE

A381784E01
0.167,0.083 0.479,0.281 0.313,0.198 10 false *A 3.927,0.094 4.24,0.292 0.313,0.198 10 false *B

a.

Place the wooden blocks or plate lift attachments in the positions shown in the illustration and set an engine lifter underneath the engine assembly with transaxle.

Text in Illustration
*A for Automatic Transaxle
*B for Manual Transaxle
V100155

Attachment Placement Position

NOTICE:
·

Place the wooden blocks or plate lift attachments so that the front suspension crossmember sub-assembly is level.

·

As the engine assembly with transaxle is very heavy, be sure to support it securely.

·

To prevent deformation of the oil pan, never set any attachments against the oil pan of the engine assembly.




b.
A246919

Remove the bolt, 2 nuts and the engine mounting insulator RH.


c.
A246920

Remove the through bolt and the nut and separate the engine mounting insulator LH.


d.
A246189

Remove the 6 bolts, and remove the engine assembly with transaxle and the front suspension crossmember from the vehicle.

NOTICE:

When removing the engine, be careful not to damage any wire harnesses of the steering shaft.



Hide 12281A 54.INSTALL NO. 1 ENGINE HANGER

a.

Remove the bolt and the oxygen sensor wiring bracket.


b.
A369825E04
0.865,1.063 1.604,0.479 1.604,0.479 2.667,1.052 false 0.344,0.115 0.656,0.313 0.313,0.198 10 false *a 2.135,0.125 2.448,0.323 0.313,0.198 10 false *b 1.521,0.281 1.833,0.479 0.313,0.198 10 false *1

Install the 2 engine hangers with the 2 bolts, as shown in the illustration.

Text in Illustration
*1 No. 1 Engine Hanger
*a Front Side
*b Rear Side

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)

HINT:
Part Name Part No.
Engine hanger 12281-21010
Bolt 91642-81025



Hide 55.REMOVE FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY

A259815

a.

Using an engine sling device and a chain block, suspend the engine assembly with transaxle and front suspension crossmember.


b.

Remove the through bolt from the engine moving control rod and remove the front suspension crossmember.


Hide 82121 56.REMOVE ENGINE WIRE

A259825

a.

Disconnect the 2 ground bolts.


b.

Disconnect all the wire harnesses and connectors. Make sure that no wire harnesses are connected to the engine.


Hide 12261 58.REMOVE VENTILATION HOSE

A259822

a.

Loosen the 2 hose clamps and remove the ventilation hose.


Hide 16502 59.REMOVE WATER FILLER SUB-ASSEMBLY

A246924

a.

Loosen the hose clamp and disconnect radiator hose No. 1 from the cylinder head.


b.
A246925

Remove the 2 nuts and the water filler sub-assembly.


Hide 17111 60.REMOVE INTAKE MANIFOLD

A117312

a.

Loosen the hose clamp and disconnect the union to connector tube hose from the booster vacuum tube.


b.
A117313

Loosen the hose clamp and disconnect the water by-pass hose from the cylinder head.


c.

Disconnect the water by-pass hose from the No. 1 water by-pass pipe.


d.
A105631

Remove the 3 bolts, 2 nuts and the intake manifold.


e.

Remove the gasket from the intake manifold.


Hide 17167 61.REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

A259840

a.

Remove the 3 bolts and the No. 1 exhaust manifold heat insulator.


Hide 25591 62.REMOVE MANIFOLD SUPPORT BRACKET

A259841

a.

Remove the 3 bolts and the manifold support bracket.


Hide 17141 63.REMOVE EXHAUST MANIFOLD

A260991

a.

Remove the 3 bolts, 2 nuts and the exhaust manifold.


Hide 11361J 64.REMOVE FLYWHEEL HOUSING UNDER COVER

Hide 65.FIX ENGINE ASSEMBLY

A259819

a.

Using an engine sling device and a chain block, hold the engine assembly.


b.

To enable removal of the engine assembly, adjust the positions of the plate lift attachments and set them in place.

NOTICE:
·

Set plate lift attachments so that the engine assembly with transaxle is level.

·

Do not perform any procedure while the engine assembly is suspended because doing so may cause the engine assembly to drop, resulting in injury. However, the engine assembly needs to be suspended when it is installed to or removed from an engine stand.

·

To prevent deformation of the oil pan, never set any attachments against the oil pan of the engine assembly.




c.

Use a belt with a tightening mechanism or a rope to secure the engine assembly with transaxle to the engine lifter.

NOTICE:
·

Do not tighten the belt with a tightening mechanism or the rope any more than is necessary.

·

Set the engine assembly with transaxle so that is horizontal.




Hide 11363A 66.REMOVE FLYWHEEL HOUSING SIDE COVER

Hide 30500 68.REMOVE AUTOMATIC TRANSAXLE ASSEMBLY (for Automatic Transaxle)

A259823

a.

Remove the bolt and wire harness bracket from the automatic transaxle assembly.


b.
C118504

Remove the 7 bolts and the automatic transaxle with torque converter.


Hide 33524F 69.REMOVE CONTROL CABLE BRACKET (for Manual Transaxle)

Hide 32101 70.REMOVE DRIVE PLATE AND RING GEAR SUB-ASSEMBLY (for Automatic Transaxle)

A107285E07
1.698,1.823 2.083,1.823 true 2.135,1.75 2.583,1.969 0.448,0.219 10 true SST

a.

Hold the crankshaft with SST.

SST
09960-10010  (09962-01000, 09963-01000)


b.
U134100

Remove the 6 bolts, drive plate spacer FR, drive plate and ring gear sub-assembly and drive plate spacer RR.


Hide 30300 71.REMOVE MANUAL TRANSAXLE ASSEMBLY (for Manual Transaxle)

a.
C063143

Remove the 7 bolts and the manual transaxle assembly.


Hide 31210 72.REMOVE CLUTCH COVER ASSEMBLY (for Manual Transaxle)

Hide 31250 73.REMOVE CLUTCH DISC ASSEMBLY (for Manual Transaxle)

Hide 13405 74.REMOVE FLYWHEEL SUB-ASSEMBLY (for Manual Transaxle)

A107285E07
1.698,1.823 2.083,1.823 true 2.135,1.75 2.583,1.969 0.448,0.219 10 true SST

a.

Hold the crankshaft with SST.

SST
09960-10010  (09962-01000, 09963-01000)


b.
A249640

Remove the 6 bolts and flywheel.


Hide 87245A 75.REMOVE INLET HEATER WATER HOSE A

A260209

a.

Disconnect heater water inlet hose A from the cylinder head.


Hide 12321B 76.REMOVE DRIVE SHAFT HEAT INSULATOR SUB-ASSEMBLY

A117317

a.

Remove the bolt, nut and the drive shaft heat insulator.


Hide 12305 77.REMOVE ENGINE MOUNTING INSULATOR RH

HINT:

Only perform this procedure when replacement of the engine mounting insulator RH is necessary.


a.
A246921

Remove the 3 bolts and engine mounting insulator RH.


Hide 12372A 78.REMOVE ENGINE MOUNTING INSULATOR LH

HINT:

Only perform this procedure when replacement of the engine mounting insulator RH is necessary.


a.
A249703

Remove the 5 bolts and engine mounting insulator LH.