Refer to DTCs C1403 and C1404 (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Separate Type Yaw Rate Sensor)>C1273).
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| C1407
C1408 |
Either of the following is detected:
1.
An open in the speed sensor signal circuit continues for 0.5 seconds or more. 2.
With the IG1 terminal voltage 9.5 V or more, the sensor power supply voltage decreases for 0.5 seconds or more. |
·
Rear speed sensor RH/LH ·
Skid control sensor wire RH/LH ·
Speed sensor circuit ·
Skid control ECU (Brake actuator assembly) |
DTC C1407 is for the rear speed sensor RH.
DTC C1408 is for the rear speed sensor LH.
Refer to DTCs C1403 and C1404 (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Separate Type Yaw Rate Sensor)>C1273).
When replacing the brake actuator assembly, perform zero point calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Separate Type Yaw Rate Sensor)>CALIBRATION).
Disassembly of the rear speed sensor from the rear axle hub and bearing assembly is prohibited.
Using the intelligent tester, check for any momentary interruption in the wire harness and connector corresponding to the DTC (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Separate Type Yaw Rate Sensor)>CHECK FOR INTERMITTENT PROBLEMS).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| RR Speed Open | RR speed sensor open detection / Normal or Error | Normal: Normal
Error: Momentary interruption |
- |
| RL Speed Open | RL speed sensor open detection / Error or Normal or Error | Normal: Normal
Error: Momentary interruption |
- |
There are no momentary interruptions.
Perform the above inspection before removing the sensor and connector.
OK
NG
OK
NG
Turn the ignition switch off.
Start the engine.
Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.
Check if the same DTC is recorded (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Separate Type Yaw Rate Sensor)>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTCs C1407 and C1408 are not output | A |
| DTCs C1407 and/or C1408 are output | B |
If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Separate Type Yaw Rate Sensor)>PROBLEM SYMPTOMS TABLE).
A
B
Turn the ignition switch off.
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
Disconnect the skid control sensor wire connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| W1-2 (+) - WK1-1 | Always | Below 1 Ω |
| W1-1 (-) - WK1-2 | Always | Below 1 Ω |
| W1-2 (+) - WK1-2 | Always | 10 kΩ or higher |
| W1-2 (+) - Body ground | Always | 10 kΩ or higher |
| W1-1 (-) - WK1-1 | Always | 10 kΩ or higher |
| W1-1 (-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| V1-2 (+) - VK1-1 | Always | Below 1 Ω |
| V1-1 (-) - VK1-2 | Always | Below 1 Ω |
| V1-2 (+) - VK1-2 | Always | 10 kΩ or higher |
| V1-2 (+) - Body ground | Always | 10 kΩ or higher |
| V1-1 (-) - VK1-1 | Always | 10 kΩ or higher |
| V1-1 (-) - Body ground | Always | 10 kΩ or higher |
Check the speed sensor signal after replacement (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Separate Type Yaw Rate Sensor)>TEST MODE PROCEDURE).
Reconnect the skid control sensor wire connector.
OK
NG
Turn the ignition switch off.
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
Disconnect the skid control ECU connector and the rear speed sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A54-17 (RR+) - W1-2 (+) | Always | Below 1 Ω |
| A54-16 (RR-) - W1-1 (-) | Always | Below 1 Ω |
| A54-5 (RL+) - V1-2 (+) | Always | Below 1 Ω |
| A54-4 (RL-) - V1-1 (-) | Always | Below 1 Ω |
| A54-17 (RR+) - Body ground | Always | 10 kΩ or higher |
| A54-16 (RR-) - Body ground | Always | 10 kΩ or higher |
| A54-5 (RL+) - Body ground | Always | 10 kΩ or higher |
| A54-4 (RL-) - Body ground | Always | 10 kΩ or higher |
Reconnect the skid control ECU connector.
OK
NG
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| W1-2 (+) - Body ground | Ignition switch ON | 8 to 14 V |
| V1-2 (+) - Body ground | Ignition switch ON | 8 to 14 V |
Check the speed sensor signal after replacement (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Separate Type Yaw Rate Sensor)>TEST MODE PROCEDURE).
If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Separate Type Yaw Rate Sensor)>PROBLEM SYMPTOMS TABLE).
| *a | Front view of wire harness connector
(to Rear Speed Sensor) |
Reconnect the rear speed sensor connector.
OK
NG