Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM(for Separate Type Yaw Rate Sensor)
RM19S0E _54 Brake _051475 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0248235 VEHICLE STABILITY CONTROL SYSTEM(for Separate Type Yaw Rate Sensor) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM(for Separate Type Yaw Rate Sensor)  C1225  SM Solenoid Circuit  C1468  SFR Solenoid Circuit  C1469  SFL Solenoid Circuit  C146A  SRR Solenoid Circuit  C146B  SRL Solenoid Circuit  


DESCRIPTION

These solenoids turn on when signals are received from the skid control ECU (brake actuator assembly) and they control the pressure acting on the wheel cylinders to control the braking force.

DTC No. DTC Detection Condition Trouble Area
C1225 When any of the following is detected:
1.

While outputting switching solenoid (SM1 or SM2) ON, overcurrent continues for 0.1 seconds or more.

2.

While outputting switching solenoid (SM1 or SM2) OFF, an open circuit continues for 0.05 seconds or more.

3.

While outputting switching solenoid (SM1 or SM2) ON, an open circuit continues for 0.05 seconds or more.

4.

While outputting switching solenoid (SM1 or SM2) OFF, current continues to be applied for 0.05 seconds or more.

5.

A condition in which the outputs from switching solenoids 1 and 2 are different continues for 0.2 seconds or more.


·

Brake actuator assembly


C1468
C1469
C146A
C146B
Open or short in the solenoid circuit continues for 0.05 seconds or more.
·

Brake actuator assembly



WIRING DIAGRAM

C243287E05
4.438,8.01 6.063,8.229 1.625,0.219 10 false Brake Actuator Assembly 4.51,3.594 5.646,3.771 1.135,0.177 10 false Skid Control ECU 5.948,1.719 6.385,1.906 0.438,0.188 10 false SFRH 5.948,2.219 6.385,2.406 0.438,0.188 10 false SFLH 5.948,2.729 6.385,2.917 0.438,0.188 10 false SRRH 5.948,3.74 6.385,3.927 0.438,0.188 10 false SFRR 5.948,3.24 6.385,3.427 0.438,0.188 10 false SRLH 5.948,4.25 6.385,4.438 0.438,0.188 10 false SFLR 5.948,4.75 6.385,4.938 0.438,0.188 10 false SRRR 5.948,5.25 6.385,5.438 0.438,0.188 10 false SRLR 6,5.75 6.313,5.938 0.313,0.188 10 false SM1 6,6.25 6.333,6.438 0.333,0.188 10 false SM2 4.563,0.771 5.531,0.938 0.969,0.167 10 false Solenoid Relay 3.552,1.365 3.854,1.531 0.302,0.167 10 false +BS 3.177,1.104 3.375,1.26 0.198,0.156 10 false 12 3.552,5.073 3.979,5.25 0.427,0.177 10 false GND1 1.51,1.385 2.24,1.552 0.729,0.167 10 false ABS NO. 2 0.667,4.156 0.958,4.313 0.292,0.156 10 false ALT 0.771,6.063 1.458,6.396 0.688,0.333 10 false Battery 3.24,4.979 3.438,5.135 0.198,0.156 10 false 1 4.438,7.854 4.708,8 0.271,0.146 10 false A54

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the brake actuator assembly, perform zero point calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Separate Type Yaw Rate Sensor)>CALIBRATION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.RECONFIRM DTC
HINT:

These codes are detected when a problem is determined in the skid control ECU (brake actuator assembly).

The solenoid circuits are in the skid control ECU (brake actuator assembly).

Therefore, solenoid circuit inspection and solenoid unit inspection cannot be performed. Be sure to check if any DTCs are output before replacing the skid control ECU (brake actuator assembly).



b.

Start the engine.


c.

Drive the vehicle at the speed of 20 km/h (12 mph) or more for 30 seconds or more.



Result
Result Proceed to
DTC is not output A
DTC is output B

HINT:
·

If a speed signal of 6 km/h (4 mph) or more is input to the skid control ECU (brake actuator assembly), with the ignition switch ON and the stop light switch off, the ECU performs self diagnosis of the motor and solenoid circuits.

·

If the normal system code is output (the trouble code is not output), slightly jiggle the connectors, wire harness, and fuses of the skid control ECU (brake actuator assembly). Make sure that no DTCs are output.

·

If any DTCs are output while jiggling a connector or wire harness from the brake actuator assembly (skid control ECU (brake actuator assembly)), inspect and repair the connector or wire harness.

·

The DTCs were probably output due to a bad connection of the connector terminal.




A

B