Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM
RM19S0E _55 Steering _051480 POWER ASSIST SYSTEMS _0248253 POWER STEERING SYSTEM C

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM  C1524  Motor Circuit Malfunction  C1555  Motor Relay Welding Failure  


DESCRIPTION

The power steering ECU assembly supplies the current to the power steering motor through the motor circuit.

DTC No. DTC Detection Condition Trouble Area
C1524 Short (or open) in motor circuit or abnormal voltage or current in motor circuit.
·

Power steering motor assembly

·

Power steering ECU assembly


C1555 Motor relay circuit malfunction.
·

Power steering motor assembly

·

Power steering ECU assembly



WIRING DIAGRAM

C243322E01
1.004,3.87 1.690,4.196 0.685,0.326 10 Battery 2.04,2.83 2.342,3.148 0.302,0.319 10 EPS 0.919,3.122 1.222,3.457 0.303,0.335 10 ALT 4.85,4.127 6.809,4.282 1.960,0.155 10 Power Steering ECU Assembly 5.322,3.6 5.759,3.797 0.437,0.197 10 PGND 5.316,2.668 5.606,2.841 0.290,0.174 10 PIG 5.316,1.325 5.557,1.488 0.240,0.163 10 M2 5.316,0.509 5.536,0.671 0.220,0.162 10 M1 4.992,0.507 5.189,0.672 0.196,0.166 10 z5 4.978,1.305 5.173,1.471 0.194,0.166 10 z5 5.022,0.331 5.130,0.497 0.108,0.166 10 1 5.022,1.128 5.130,1.293 0.108,0.166 10 2 4.94,3.605 5.206,3.770 0.266,0.166 10 A42 5.022,3.429 5.130,3.595 0.108,0.166 10 2 4.94,2.648 5.206,2.814 0.266,0.166 10 A42 5.022,2.473 5.130,2.638 0.108,0.166 10 1 2.608,1.81 4.625,1.973 2.017,0.163 10 Power Steering Motor Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

If the power steering ECU assembly or power steering motor assembly has been replaced, perform the torque sensor zero point calibration and assist map writing (See page Steering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>CALIBRATION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.INSPECT POWER STEERING ECU ASSEMBLY
a.

Start the engine.


U126947E02
2.333,1.365 2.802,1.865 true 1.604,1.375 0.979,1.865 true 1.896,1.375 1.896,1.854 true 2.625,1.885 3.073,2.063 0.448,0.177 10 false PGND 1.823,1.885 2.063,2.073 0.24,0.188 10 false M1 0.802,1.875 1.094,2.052 0.292,0.177 10 false M2 0.198,0.146 0.385,0.302 0.188,0.156 10 false *a 1.688,0.51 1.896,0.667 0.208,0.156 10 false z5 2.313,0.521 2.625,0.688 0.313,0.167 10 false A42

b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
z5-1 (M1) - A42-2 (PGND) Engine running
Steering wheel turned to right
11 to 14 V
Engine running
steering wheel turned to left
6 to 11 V
z5-2 (M2) - A42-2 (PGND) Engine running
Steering wheel turned to right
6 to 11 V
Engine running
steering wheel turned to left
11 to 14 V


Text in Illustration
*a Component with harness connected
(Power Steering ECU Assembly)



OK

2.INSPECT POWER STEERING MOTOR ASSEMBLY

NG

3.CHECK HARNESS AND CONNECTOR (POWER STEERING ECU ASSEMBLY - BATTERY AND BODY GROUND)
2.INSPECT POWER STEERING MOTOR ASSEMBLY
a.

Disconnect the power steering ECU assembly connector.


U126948E02
1.531,2.469 1.323,2.75 true 1.854,2.469 2.063,2.75 true 2.01,2.781 2.281,2.99 0.271,0.208 10 false M1 1.177,2.781 1.438,2.979 0.26,0.198 10 false M2 0.156,0.135 0.385,0.354 0.229,0.219 10 false *a 0.896,2.333 1.104,2.49 0.208,0.156 10 false z5

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z5-1 (M1) - z5-2 (M2) Always 0.1 to 1.0 Ω
z5-1 (M1) - Body ground Always 1 MΩ or higher
z5-2 (M2) - Body ground Always 1 MΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to Power Steering ECU Assembly)

Result
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C



A

3.CHECK HARNESS AND CONNECTOR (POWER STEERING ECU ASSEMBLY - BATTERY AND BODY GROUND)

B

REPLACE POWER STEERING MOTOR ASSEMBLY

C

REPLACE POWER STEERING MOTOR ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (POWER STEERING ECU ASSEMBLY - BATTERY AND BODY GROUND)
a.

Disconnect the power steering ECU assembly connector.


U126949E02
2.25,2.438 2.01,2.979 true 2.615,2.427 2.844,2.969 true 2.76,2.99 3.073,3.198 0.313,0.208 10 false PIG 1.813,3 2.26,3.188 0.448,0.188 10 false PGND 0.125,0.104 0.313,0.26 0.188,0.156 10 false *a 1.563,2.26 1.854,2.458 0.292,0.198 10 false A42

b.

Measure the voltage according to the value(s) in the table below.


Standard Voltage:
Tester Connection Condition Specified Condition
A42-1 (PIG) - Body ground Always 11 to 14 V


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A42-2 (PGND) - Body ground Always Below 1 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Power Steering ECU Assembly)

Result
Result Proceed to
NG A
OK (for LHD) B
OK (for RHD) C



A

REPAIR OR REPLACE HARNESS OR CONNECTOR

B

REPLACE POWER STEERING ECU ASSEMBLY

C

REPLACE POWER STEERING ECU ASSEMBLY