Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM
RM19S0E _55 Steering _051480 POWER ASSIST SYSTEMS _0248253 POWER STEERING SYSTEM C

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM  C1553  PIG Power Supply Overvoltage  


DESCRIPTION

If the power steering ECU assembly determines that the motor power source voltage and the IG voltage are not within the specified range, it stops the power assist as a fail-safe function.

DTC No. DTC Detection Condition Trouble Area
C1553
·

PIG power source overvoltage

·

IG power source overvoltage


·

IG and PIG power source circuits

·

Power steering ECU assembly



WIRING DIAGRAM

C240046E02
0.802,0.573 2.167,0.823 1.365,0.25 10 false from IG1 NO. 1 Relay 1.365,1.042 2.188,1.323 0.823,0.281 10 false from Battery 2.5,0.729 3.438,0.927 0.938,0.198 10 false ECU-IG NO. 1 2.792,1.229 3.146,1.458 0.354,0.229 10 false EPS 5.323,0.583 5.5,0.729 0.177,0.146 10 false IG 5.031,0.583 5.219,0.729 0.188,0.146 10 false F6 5.073,0.396 5.177,0.563 0.104,0.167 10 false 1 5.073,0.875 5.177,1.042 0.104,0.167 10 false 1 4.99,1.052 5.26,1.208 0.271,0.156 10 false A42 5.073,1.375 5.208,1.563 0.135,0.188 10 false 2 4.979,1.563 5.25,1.719 0.271,0.156 10 false A42 5.333,1.063 5.604,1.208 0.271,0.146 10 false PIG 5.333,1.573 5.885,1.719 0.552,0.146 10 false PGND 4.771,2.125 6.708,2.385 1.938,0.26 10 false Power Steering ECU Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

If the power steering ECU assembly has been replaced, perform the torque sensor zero point calibration and assist map writing (See page Steering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>CALIBRATION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (IG)
a.
U126950E03
0.844,2.396 1.042,2.813 true 2.24,2.51 2.083,2.823 true 0.188,0.115 0.375,0.271 0.188,0.156 10 false *a 1,2.833 1.229,3.031 0.229,0.198 10 false IG 1.802,2.844 2.25,3.01 0.448,0.167 10 false PGND 0.677,1.771 0.865,1.927 0.188,0.156 10 false F6 2.302,1.771 2.594,1.927 0.292,0.156 10 false A42

Disconnect the power steering ECU assembly connectors.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F6-1 (IG) - A42-2 (PGND) Ignition switch ON 11 to 14 V


Text in Illustration
*a Rear view of wire harness connector
(to Power Steering ECU Assembly)



OK

2.CHECK HARNESS AND CONNECTOR (POWER STEERING ECU ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (POWER STEERING ECU ASSEMBLY - BODY GROUND)

A

REPAIR OR REPLACE HARNESS OR CONNECTOR

B

REPLACE POWER STEERING ECU ASSEMBLY

C

REPLACE POWER STEERING ECU ASSEMBLY