Home › Steering › STEERING COLUMN › STEERING COLUMN ASSEMBLY(for LHD)
RM19S0E _55 Steering _051481 STEERING COLUMN _0248256 STEERING COLUMN ASSEMBLY(for LHD) A

STEERING COLUMN  STEERING COLUMN ASSEMBLY(for LHD)  REMOVAL  


CAUTION / NOTICE / HINT

CAUTION:

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (w/ VSC/Built-in Type Yaw Rate Sensor)>PRECAUTION).


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 2. POSITION FRONT WHEELS FACING STRAIGHT AHEAD

Hide 3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


Hide 45100 5.REMOVE STEERING WHEEL ASSEMBLY

Hide 45287 6.REMOVE LOWER STEERING COLUMN COVER

C241416

a.

Remove the 3 screws.


b.
C241417

Disengage the 4 claws and remove the lower steering column cover.


Hide 45286B 7.REMOVE UPPER STEERING COLUMN COVER

C241418

a.

Disengage the claw and remove the upper steering column cover.


Hide 8.REMOVE COMBINATION SWITCH ASSEMBLY

a.

Disconnect all connectors from the combination switch assembly.


b.
C241419

Use pliers to hold the clamp and raise the claw with a screwdriver. Remove the combination switch assembly from the steering column assembly.


Hide 55106 9.REMOVE BRAKE PEDAL SUPPORT SUB-ASSEMBLY

Hide 45259A 10.REMOVE COLUMN HOLE COVER SILENCER SHEET

a.
C229653

Remove the 2 clips and the column hole cover silencer sheet.


Hide 45209 11.REMOVE STEERING SLIDING YOKE SUB-ASSEMBLY

C205442E07
1,1.667 0.604,1.708 0.604,1.708 0.969,1.75 true 2.469,0.208 2.146,0.104 2.146,0.104 2.406,0.25 true 2.042,0.958 1.75,0.958 false 1.792,1.802 1.552,1.802 1.552,1.802 1.24,1.51 false 1.625,1.51 1.76,1.667 0.135,0.156 10 false A 1.385,1.906 1.51,2.063 0.125,0.156 10 false B 2.594,0.604 2.719,0.76 0.125,0.156 10 false C 0.427,1.625 0.594,1.781 0.167,0.156 10 false *a 1.979,0 2.146,0.156 0.167,0.156 10 false *a 2.052,0.885 2.219,1.042 0.167,0.156 10 false *1 1.813,1.719 1.979,1.875 0.167,0.156 10 false *2

a.

Place matchmarks on the No. 2 steering intermediate shaft assembly and the steering column assembly.

Text in Illustration
*1 No. 2 Steering Intermediate Shaft Assembly
*2 Steering Sliding Yoke Sub-assembly
*a Matchmark


b.

Place matchmarks on the steering sliding yoke sub-assembly and the steering gear assembly.


c.

Loosen bolt A.


d.

Loosen bolt C.


e.

Remove bolt B and detach the steering sliding yoke sub-assembly from the steering gear assembly.


Hide 45250 12.REMOVE STEERING COLUMN ASSEMBLY

a.
C241420

Separate the wire harness clamp from the power steering ECU assembly.


b.

Disconnect the 2 steering column assembly connectors from the power steering ECU assembly.


c.

Disconnect all connectors and detach all wire harness clamps from the steering column assembly.


d.
C241421

Remove the bolt, 2 nuts and the steering column assembly from the instrument panel reinforcement assembly.