Home › Steering › STEERING COLUMN › STEERING COLUMN ASSEMBLY(for RHD)
RM19S0E _55 Steering _051481 STEERING COLUMN _0248257 STEERING COLUMN ASSEMBLY(for RHD) A

STEERING COLUMN  STEERING COLUMN ASSEMBLY(for RHD)  REMOVAL  


CAUTION / NOTICE / HINT

CAUTION:

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (w/ VSC/Built-in Type Yaw Rate Sensor)>PRECAUTION).


PROCEDURE

Hide 1. POSITION FRONT WHEELS FACING STRAIGHT AHEAD

Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


Hide 45100 4.REMOVE STEERING WHEEL ASSEMBLY

Hide 45287 5.REMOVE LOWER STEERING COLUMN COVER

a.
C232521

Remove the 3 screws, disengage the 4 claws, release the tilt lever and remove the lower steering column cover.


Hide 45286B 6.REMOVE UPPER STEERING COLUMN COVER

a.
C232522

Disengage the claw and remove the upper steering column cover.


Hide 7.REMOVE COMBINATION SWITCH ASSEMBLY

a.

Disconnect all connectors from the combination switch assembly.


b.
C233274E01
2.103,0.265 2.267,0.413 0.164,0.148 10 *a 2.103,0.601 2.267,0.749 0.164,0.148 10 *b 2.092,0.346 1.805,0.346 false

Use pliers to hold the clamp and raise the claw with a screwdriver. Remove the combination switch assembly from the steering column assembly.

Text in Illustration
*a Loosen The Clamp
*b Raise The Claw


Hide 55106 8.REMOVE BRAKE PEDAL SUPPORT SUB-ASSEMBLY

Hide 45259A 9.REMOVE COLUMN HOLE COVER SILENCER SHEET

a.
C234877

Remove the floor carpet and 2 clips and remove the column hole cover silencer sheet.


Hide 45209 10.REMOVE STEERING SLIDING YOKE SUB-ASSEMBLY

a.
C205442E07
1,1.667 0.604,1.708 0.604,1.708 0.969,1.75 true 2.469,0.208 2.146,0.104 2.146,0.104 2.406,0.25 true 2.042,0.958 1.75,0.958 false 1.792,1.802 1.552,1.802 1.552,1.802 1.24,1.51 false 1.625,1.51 1.76,1.667 0.135,0.156 10 false A 1.385,1.906 1.51,2.063 0.125,0.156 10 false B 2.594,0.604 2.719,0.76 0.125,0.156 10 false C 0.427,1.625 0.594,1.781 0.167,0.156 10 false *a 1.979,0 2.146,0.156 0.167,0.156 10 false *a 2.052,0.885 2.219,1.042 0.167,0.156 10 false *1 1.813,1.719 1.979,1.875 0.167,0.156 10 false *2

Place matchmarks on the No. 2 steering intermediate shaft assembly and the steering column assembly.

Text in Illustration
*1 No. 2 Steering Intermediate Shaft Assembly
*2 Steering Sliding Yoke Sub-assembly
*a Matchmark


b.

Place matchmarks on the steering sliding yoke sub-assembly and the steering gear assembly.


c.

Loosen bolt A.


d.

Loosen bolt C.


e.

Remove bolt B and detach the steering sliding yoke sub-assembly from the steering gear assembly.


Hide 45250 11.REMOVE STEERING COLUMN ASSEMBLY

a.
C233275

Separate the wire harness clamp from the power steering ECU assembly.


b.

Disconnect the 2 steering column assembly connectors from the power steering ECU assembly.


c.

Disconnect all connectors and detach all wire harness clamps from the steering column assembly.


d.
C232524

Remove the bolt, the 2 nuts and the steering column assembly from the instrument panel reinforcement assembly.