Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(for Radio and Display Type) › from 2014.07
RM19S0E _56 Audio / Visual / Telematics _051483 AUDIO / VIDEO _0248274 AUDIO AND VISUAL SYSTEM(for Radio and Display Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type)  Radio Broadcast cannot be Received or Poor Reception  


WIRING DIAGRAM

E291132E18
0.833,0.313 2.125,1 1.292,0.688 10 false Roof Antenna Pole Sub-assembly 5.781,2.521 7.094,3.25 1.313,0.729 10 false Radio and Display Receiver Assembly 4.406,2.344 5.469,2.99 1.063,0.646 10 false Antenna Cord Sub-assembly 2.031,2.344 3.375,3.042 1.344,0.698 10 false No. 2 Antenna Cord Sub-assembly 4.177,1.271 4.302,1.427 0.125,0.156 10 false 2 4.167,1.552 4.396,1.708 0.229,0.156 10 false 1 3.24,1.26 3.365,1.417 0.125,0.156 10 false 2 3.24,1.542 3.469,1.698 0.229,0.156 10 false 1 6.042,1.333 6.75,1.49 0.708,0.156 10 false MAIN 6.042,1.656 6.667,1.813 0.625,0.156 10 false ANT+ 5.469,1.26 5.573,1.417 0.104,0.156 10 false 3 5.469,1.542 5.698,1.698 0.229,0.156 10 false 5 2.083,1.271 2.188,1.427 0.104,0.156 10 false 2 2.083,1.552 2.313,1.708 0.229,0.156 10 false 3 5.781,2.365 6.063,2.521 0.281,0.156 10 false RA 0.208,2 1.552,2.688 1.344,0.688 10 false No. 1 Amplifier Antenna Assembly

CAUTION / NOTICE / HINT

NOTICE:

Check that the wire harness is properly installed and does not have any sharp bends, pinching or loose connections (See page General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE).


PROCEDURE

1.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY
a.

Check the radio automatic station search function by activating it.

OK:

Automatic station search function stops on a station.




OK

NG

2.CHECK OPTIONAL COMPONENTS
2.CHECK OPTIONAL COMPONENTS
a.

Check if any optional components that may decrease reception capacity, such as sunshade film or a telephone antenna, are installed.

OK:

Optional components are not installed.


NOTICE:

Do not remove optional components without the permission of the customer.




OK

3.CHECK RADIO ANTENNA

NG

REMOVE OPTIONAL COMPONENTS AND CHECK AGAIN (SEE NOTICE ABOVE)

3.CHECK RADIO ANTENNA
a.

Remove the roof antenna pole sub-assembly from the amplifier antenna assembly.


b.

Turn the ignition switch to ACC with the radio and display receiver assembly connector connected.


c.

Place a screwdriver, thin wire or other metal object on the amplifier antenna threaded installation position for the roof antenna pole sub-assembly, and check that noise can be heard from the speakers.

OK:

Noise can be heard from the speakers.




OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

4.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY
4.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY
a.
E276819

Remove the antenna connector from the radio and display receiver assembly.


b.

Turn the ignition switch to ACC with the radio and display receiver assembly connector connected.


c.

Turn the radio on and tune into AM mode.


d.

Place a screwdriver, thin wire or other metal object on the radio and display receiver assembly antenna jack and check that noise can be heard from the speakers.

OK:

Noise can be heard from the speakers.




OK

5.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

5.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY
a.
E188455E48
1.521,1.125 1.115,1.479 true 0.833,1.479 1.229,1.646 0.396,0.167 10 false ANT+

Disconnect the RA radio and display receiver assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
5 (ANT+) - Body ground Ignition switch ACC
Radio switch on and FM or AM selected
11 to 14 V




OK

6.CHECK ANTENNA CORD SUB-ASSEMBLY

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

6.CHECK ANTENNA CORD SUB-ASSEMBLY
a.
U158745E02
1.698,1.24 1.104,1.458 true 2.729,0.771 2.146,0.979 true 0.927,0.875 1.135,1.052 0.208,0.177 10 false RA 0.104,0.125 0.333,0.323 0.229,0.198 10 false *a 0.115,1.813 0.344,2.01 0.229,0.198 10 false *b 2.771,0.667 3.219,0.865 0.448,0.198 10 false ANT+ 0.698,1.385 1.146,1.583 0.448,0.198 10 false MAIN

Disconnect the radio and display receiver assembly connector.


b.

Remove the antenna connector from the No. 2 antenna cord sub-assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
RA-3 (MAIN) - 2 Always Below 1 Ω
RA-5 (ANT+) - 1 Always Below 1 Ω
RA-3 (MAIN) - Body ground Always 10 kΩ or higher
RA-5 (ANT+) - Body ground Always 10 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)
*b Front view of wire harness connector
(to No. 2 Antenna Cord Sub-assembly)



OK

7.CHECK NO. 2 ANTENNA CORD SUB-ASSEMBLY

NG

REPLACE ANTENNA CORD SUB-ASSEMBLY

7.CHECK NO. 2 ANTENNA CORD SUB-ASSEMBLY
a.
E298846E04
0.519,0.231 0.748,0.444 0.230,0.213 10 *a 0.582,1.9 0.812,2.113 0.230,0.213 10 *b

Remove the antenna connector from the antenna cord sub-assembly.


b.

Remove the antenna connector from the No. 1 amplifier antenna assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 - 2 Always Below 1 Ω
1 - 3 Always Below 1 Ω
2 - Body ground Always 10 kΩ or higher
1 - Body ground Always 10 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to Antenna Cord Sub-assembly)
*b Front view of wire harness connector
(to No. 1 Amplifier Antenna Assembly)



OK

8.CHECK ROOF ANTENNA POLE SUB-ASSEMBLY

NG

REPLACE NO. 2 ANTENNA CORD SUB-ASSEMBLY

8.CHECK ROOF ANTENNA POLE SUB-ASSEMBLY
a.

Check that the roof antenna pole sub-assembly is securely installed.

OK:

The roof antenna pole sub-assembly is installed properly.




OK

9.CHECK ROOF ANTENNA POLE SUB-ASSEMBLY

NG

REINSTALL ROOF ANTENNA POLE SUB-ASSEMBLY

9.CHECK ROOF ANTENNA POLE SUB-ASSEMBLY
a.

Replace the roof antenna pole sub-assembly and check if radio broadcasts can be received normally.

OK:

Radio broadcasts can be received normally.




OK

END (ROOF ANTENNA POLE SUB-ASSEMBLY WAS DEFECTIVE)

NG

10.CHECK NO. 1 AMPLIFIER ANTENNA ASSEMBLY
10.CHECK NO. 1 AMPLIFIER ANTENNA ASSEMBLY
a.

Replace the No. 1 amplifier antenna assembly and check if radio broadcasts can be received normally (See page Audio / Visual / Telematics>AUDIO / VIDEO>AMPLIFIER ANTENNA>REMOVAL).

OK:

Radio broadcasts can be received normally.




OK

END (NO. 1 AMPLIFIER ANTENNA ASSEMBLY WAS DEFECTIVE)

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY