Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM › from 2014.07
RM19S0E _56 Audio / Visual / Telematics _051484 NAVIGATION / MULTI INFO DISPLAY _0248277 NAVIGATION SYSTEM J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  Microphone Circuit between Microphone and Navigation Receiver Assembly  


DESCRIPTION

The navigation receiver assembly and telephone microphone assembly are connected to each other using the microphone connection detection signal lines.

Using this circuit, the navigation receiver assembly sends power to the telephone microphone assembly, and the telephone microphone assembly sends microphone signals to the navigation receiver assembly.

WIRING DIAGRAM

B378031E04
5.594,0.667 6.323,0.823 0.729,0.156 10 false MACC 5.594,1.51 6.094,1.667 0.5,0.156 10 false MIN+ 5.594,1.073 6.063,1.229 0.469,0.156 10 false MIN- 1.458,0.677 1.896,0.833 0.438,0.156 10 false MACC 1.448,1.51 1.896,1.667 0.448,0.156 10 false MCO+ 1.49,1.073 1.896,1.229 0.406,0.156 10 false MCO- 5.594,2.375 6.094,2.531 0.5,0.156 10 false SNS2 5.594,1.969 6.063,2.125 0.469,0.156 10 false SGND 3.656,2.115 4.229,2.313 0.573,0.198 10 false Shielded 1.5,2.406 1.896,2.563 0.396,0.156 10 false SNS2 5.385,3 6.688,3.427 1.302,0.427 10 false Navigation Receiver Assembly 0.708,3.052 2.094,3.479 1.385,0.427 10 false Amplifier Microphone Assembly 2.01,0.542 2.219,0.74 0.208,0.198 10 false 1 5.354,0.542 5.563,0.74 0.208,0.198 10 false 4 5.292,0.969 5.5,1.167 0.208,0.198 10 false 19 5.292,1.865 5.5,2.063 0.208,0.198 10 false 18 5.365,1.385 5.573,1.583 0.208,0.198 10 false 5 5.365,2.281 5.573,2.479 0.208,0.198 10 false 6 2.01,0.958 2.219,1.156 0.208,0.198 10 false 3 2.01,1.385 2.219,1.583 0.208,0.198 10 false 2 2.01,2.271 2.219,2.469 0.208,0.198 10 false 4 0.719,2.833 1.115,3.031 0.396,0.198 10 false F95 5.375,2.823 5.771,3.021 0.396,0.198 10 false F132

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - AMPLIFIER MICROPHONE ASSEMBLY)
a.

Disconnect the F132 navigation receiver assembly connector.


b.

Disconnect the F95 amplifier microphone assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F132-6 (SNS2) - F95-4 (SNS2) Always Below 1 Ω
F132-4 (MACC) - F95-1 (MACC) Always Below 1 Ω
F132-5 (MIN+) - F95-2 (MCO+) Always Below 1 Ω
F132-19 (MIN-) - F95-3 (MCO-) Always Below 1 Ω
F132-6 (SNS2) - Body ground Always 10 kΩ or higher
F132-4 (MACC) - Body ground Always 10 kΩ or higher
F132-5 (MIN+) - Body ground Always 10 kΩ or higher
F132-19 (MIN-) - Body ground Always 10 kΩ or higher
F132-18 (SGND) - Body ground Always 10 kΩ or higher




OK

2.CHECK NAVIGATION RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK NAVIGATION RECEIVER ASSEMBLY
a.

Reconnect the F132 navigation receiver assembly connector.


b.

Reconnect the F95 amplifier microphone assembly connector.


c.
U158707E02
2.219,1.021 2.792,0.396 true 2.188,1.229 2.625,1.74 true 2.042,1.24 2.01,1.74 true 2.844,0.292 3.26,0.531 0.417,0.24 10 false MACC 2.479,1.75 3.01,1.938 0.531,0.188 10 false SGND 0.063,0.031 0.219,0.198 0.156,0.167 10 false *a 0.177,0.385 0.542,0.531 0.365,0.146 10 false F132 1.854,1.75 2.198,1.885 0.344,0.135 10 false MIN-

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F132-4 (MACC) - Body ground Ignition switch ACC 4 to 6 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F132-18 (SGND) - Body ground Always Below 1 Ω
F132-19 (MIN-) - Body ground Always Below 1 Ω



Text in Illustration
*a Component with harness connected
(Navigation Receiver Assembly)


OK

3.INSPECT AMPLIFIER MICROPHONE ASSEMBLY

NG

3.INSPECT AMPLIFIER MICROPHONE ASSEMBLY
a.
E228890E09
0.157,0.082 0.348,0.273 0.191,0.191 10 *a 1.725,1.762 2.138,1.930 0.412,0.167 10 MCO- 1.057,1.762 1.469,1.930 0.412,0.167 10 SNS2 1.519,1.254 1.302,1.762 false 1.657,1.254 1.917,1.762 false

Remove the amplifier microphone assembly (See page Audio / Visual / Telematics>AUDIO / VIDEO>MICROPHONE AMPLIFIER>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4 (SNS2) - 3 (MCO-) Always Below 1 Ω


Text in Illustration
*a Component without harness connected
(Amplifier Microphone Assembly)



OK

4.CHECK AMPLIFIER MICROPHONE ASSEMBLY

NG

REPLACE AMPLIFIER MICROPHONE ASSEMBLY

4.CHECK AMPLIFIER MICROPHONE ASSEMBLY
a.
U158691E02
1.563,1.344 1.073,1.74 false 1.917,1.344 2.396,1.74 false 0.177,0.115 0.573,0.406 0.396,0.292 10 false *a 0.542,1.646 0.99,1.833 0.448,0.188 10 false MCO- 2.438,1.646 2.885,1.833 0.448,0.188 10 false MCO+ 1.635,0.26 1.917,0.417 0.281,0.156 10 false F95

Turn the ignition switch to ACC.


b.

Connect an oscilloscope to terminals 2 (MCO+) and 3 (MCO-).


c.

Check the waveform of the amplifier microphone assembly using the oscilloscope.

Text in Illustration
*a Component with harness connected
(Amplifier Microphone Assembly)

Result
Result Proceed to
A waveform synchronized with the voice input to the amplifier microphone assembly is output A
A waveform synchronized with the voice input to the amplifier microphone assembly is not output B



A

B

REPLACE AMPLIFIER MICROPHONE ASSEMBLY