Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › REAR VIEW MONITOR SYSTEM › from 2014.07
RM19S0E _56 Audio / Visual / Telematics _051485 PARK ASSIST / MONITORING _0248279 REAR VIEW MONITOR SYSTEM C

PARK ASSIST / MONITORING  REAR VIEW MONITOR SYSTEM  C1622  Open or Short Circuit in Back Camera Signal  


DESCRIPTION

This DTC is stored if the radio and display receiver assembly*1 or navigation receiver assembly*2 judges as a result of its self check that the signals or signal lines between the radio and display receiver assembly and the rear television camera assembly are not normal.

*1: w/o Navigation System

*2: w/ Navigation System


DTC Code DTC Detection Condition Trouble Area
C1622 Open or Short Circuit in rear television camera signal
·

Harness or connector

·

Rear television camera assembly

·

Radio and display receiver assembly (w/o Navigation System)

·

Navigation Receiver Assembly (w/ Navigation System)



WIRING DIAGRAM

E299058E02
4.448,1.031 4.635,1.198 0.188,0.167 10 false 11 4.833,1.021 5.021,1.188 0.188,0.167 10 false 11 5.156,1.188 5.479,1.344 0.323,0.156 10 false CA+ 4.375,1.198 4.76,1.344 0.385,0.146 10 false F133 4.75,1.198 5.125,1.385 0.375,0.188 10 false F128 4.854,1.375 5.01,1.542 0.156,0.167 10 false *1 4.448,1.375 4.604,1.542 0.156,0.167 10 false *2 2.313,1.115 2.469,1.302 0.156,0.188 10 false 6 1.938,1.177 2.26,1.354 0.323,0.177 10 false CB+ 1.958,1.896 2.26,2.063 0.302,0.167 10 false CV+ 2.323,1.813 2.448,1.969 0.125,0.156 10 false 3 4.438,1.74 4.635,1.906 0.198,0.167 10 false 12 4.833,1.74 5.031,1.906 0.198,0.167 10 false 12 4.854,2.083 5.01,2.25 0.156,0.167 10 false *1 4.448,2.083 4.604,2.25 0.156,0.167 10 false *2 5.156,1.906 5.479,2.063 0.323,0.156 10 false V+ 5.156,2.604 5.479,2.76 0.323,0.156 10 false V- 4.854,2.781 5.01,2.948 0.156,0.167 10 false *1 4.448,2.792 4.604,2.958 0.156,0.167 10 false *2 4.854,3.5 5.01,3.667 0.156,0.167 10 false *1 4.448,3.5 4.604,3.667 0.156,0.167 10 false *2 4.458,2.438 4.646,2.604 0.188,0.167 10 false 24 4.854,2.438 5.042,2.604 0.188,0.167 10 false 24 4.438,3.156 4.625,3.313 0.188,0.156 10 false 23 4.833,3.156 5.021,3.313 0.188,0.156 10 false 23 5.146,3.313 5.656,3.531 0.51,0.219 10 false CGND 1.958,2.604 2.26,2.771 0.302,0.167 10 false CV- 1.823,3.313 2.26,3.635 0.438,0.323 10 false CGND 2.313,2.531 2.49,2.688 0.177,0.156 10 false 2 2.313,3.24 2.583,3.396 0.271,0.156 10 false 5 3.323,3.448 4.104,3.667 0.781,0.219 10 false Shielded 0.594,3.844 0.927,4 0.333,0.156 10 false P15 0.594,3.99 2.896,4.292 2.302,0.302 10 false Rear Television Camera Assembly 4.563,3.875 7.125,4.208 2.563,0.333 10 false Radio and Display Receiver Assembly*1 0.188,4.844 2.021,5.156 1.833,0.313 10 false *1: w/o Navigation System 0.188,5.156 1.99,5.5 1.802,0.344 10 false *2: w/ Navigation System 4.375,1.917 4.76,2.063 0.385,0.146 10 false F133 4.385,2.615 4.771,2.76 0.385,0.146 10 false F133 4.385,3.323 4.771,3.469 0.385,0.146 10 false F133 4.76,1.917 5.135,2.104 0.375,0.188 10 false F128 4.75,2.615 5.125,2.802 0.375,0.188 10 false F128 4.75,3.323 5.125,3.51 0.375,0.188 10 false F128 4.563,4.208 7.104,4.573 2.542,0.365 10 false Navigation Receiver Assembly*2

PROCEDURE

1.CHECK FOR DTC

A

B

2.CHECK HARNESS AND CONNECTOR (RECEIVER ASSEMBLY - REAR TELEVISION CAMERA ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (RECEIVER ASSEMBLY - REAR TELEVISION CAMERA ASSEMBLY)
a.

Disconnect the F128*1 or F133*2 radio and display receiver assembly connector*1 or navigation receiver assembly connector*2.


b.

Disconnect the P15 rear television camera assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F128-11 (CA+) - P15-6 (CB+)*1 Always Below 1 Ω
F128-12 (V+) - P15-3 (CV+)*1 Always Below 1 Ω
F128-23 (CGND) - P15-5 (CGND)*1 Always Below 1 Ω
F128-24 (V-) - P15-2 (CV-)*1 Always Below 1 Ω
F128-11 (CA+) - Body ground*1 Always 10 kΩ or higher
F128-12 (V+) - Body ground*1 Always 10 kΩ or higher
F128-23 (CGND) - Body ground*1 Always 10 kΩ or higher
F128-24 (V-) - Body ground*1 Always 10 kΩ or higher
F133-11 (CA+) - P15-6 (CB+)*2 Always Below 1 Ω
F133-12 (V+) - P15-3 (CV+)*2 Always Below 1 Ω
F133-23 (CGND) - P15-5 (CGND)*2 Always Below 1 Ω
F133-24 (V-) - P15-2 (CV-)*2 Always Below 1 Ω
F133-11 (CA+) - Body ground*2 Always 10 kΩ or higher
F133-12 (V+) - Body ground*2 Always 10 kΩ or higher
F133-23 (CGND) - Body ground*2 Always 10 kΩ or higher
F133-24 (V-) - Body ground*2 Always 10 kΩ or higher


*1: w/o Navigation System

*2: w/ Navigation System




OK

3.CHECK RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK RECEIVER ASSEMBLY
a.
U158723E02
0.927,1.271 0.677,1.521 true 1.083,1.271 0.938,1.896 true 2.469,0.271 2.917,0.438 0.448,0.167 10 false *B 2.021,0.292 2.469,0.458 0.448,0.167 10 false F133 1.344,0.281 1.792,0.448 0.448,0.167 10 false *A 0.906,0.292 1.354,0.458 0.448,0.167 10 false F128 0.708,1.896 1.198,2.094 0.49,0.198 10 false CGND 0.51,1.51 0.75,1.708 0.24,0.198 10 false V- 0.094,0.083 0.333,0.281 0.24,0.198 10 false *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F128-23 (CGND) - Body ground*1 Always Below 1 Ω
F128-24 (V-) - Body ground*1 Always Below 1 Ω
F133-23 (CGND) - Body ground*2 Always Below 1 Ω
F133-24 (V-) - Body ground*2 Always Below 1 Ω


*1: w/o Navigation System

*2: w/ Navigation System


Text in Illustration
*A w/o Navigation System
*B w/ Navigation System
*a Component with harness connected
(Radio and Display Receiver Assembly*1 or Navigation Receiver Assembly*2)


Result
Result Proceed to
OK A
NG (w/o Navigation System) B
NG (w/ Navigation System) C


A

4.CHECK RECEIVER ASSEMBLY

B

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

C

4.CHECK RECEIVER ASSEMBLY
a.
U158710E02
1.906,1.5 2.719,1.635 true 1.635,1.5 0.813,1.625 true 0.104,0.083 0.5,0.271 0.396,0.188 10 false *a 1.583,0.281 1.948,0.469 0.365,0.188 10 false P15 2.781,1.583 3.219,1.771 0.438,0.188 10 false CB+ 0.365,1.542 0.802,1.729 0.438,0.188 10 false CGND

Disconnect the rear television camera assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
P15-6 (CB+) - P15-5 (CGND) Ignition switch ACC 5.5 to 7.1 V


Text in Illustration
*a Front view of wire harness connector
(to Rear Television Camera Assembly)


Result
Result Proceed to
OK A
NG (w/o Navigation System) B
NG (w/ Navigation System) C


A

5.CHECK REAR TELEVISION CAMERA ASSEMBLY

B

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

C

5.CHECK REAR TELEVISION CAMERA ASSEMBLY
a.

Using an oscilloscope, check the waveform.

U158716E02
0.583,1.323 0.354,0.781 true 0.583,1.51 0.354,2.063 true 2.792,1.906 2.573,2.427 false 2.906,1.792 3.073,2.438 false 5.427,1.74 5.292,2.427 false 5.563,1.677 5.75,2.417 false 0.146,0.656 0.385,0.823 0.24,0.167 10 false V+ 0.073,0.146 0.313,0.313 0.24,0.167 10 false *a 2.281,0.146 2.521,0.313 0.24,0.167 10 false *b 2.469,2.438 2.708,2.604 0.24,0.167 10 false *d 4.833,0.146 5.073,0.313 0.24,0.167 10 false *c 2.021,1.354 2.427,1.521 0.406,0.167 10 false GND 1.5,0.719 1.708,0.885 0.208,0.167 10 false *B 0.667,0.719 0.865,0.885 0.198,0.167 10 false *A 1.427,0.458 1.833,0.625 0.406,0.167 10 false F133 0.583,0.469 0.99,0.635 0.406,0.167 10 false F128 4.604,1.354 5.01,1.521 0.406,0.167 10 false GND 0.26,2.073 0.5,2.24 0.24,0.167 10 false V- 3.021,2.448 3.26,2.615 0.24,0.167 10 false *e 5.219,2.448 5.458,2.615 0.24,0.167 10 false *d 5.677,2.427 5.917,2.594 0.24,0.167 10 false *e

Text in Illustration
*A w/o Navigation System *B w/ Navigation System
*a Component with harness connected
(Radio and Display Receiver Assembly*1 or Navigation Receiver Assembly*2)
*b Waveform 1
*c Waveform 2 *d Synchronized Signal
*e Video Waveform - -

Measurement Condition
Item Content
Tester Connection F128-12 (V+) - F128-24 (V-)*1
F133-12 (V+) - F133-24 (V-)*2
Tool Setting 0.2 V/DIV., 50 μs/DIV.
Condition

Waveform 1: Ignition switch ON, shift lever in R

Waveform 2: Ignition switch ON, shift lever in R, screen blacked out by covering camera lens



*1: w/o Navigation System

*2: w/ Navigation System


OK:

Waveform is as shown in illustration.


HINT:

The video waveform changes according to the image sent by the rear television camera assembly.




OK

NG

6.REPLACE REAR TELEVISION CAMERA ASSEMBLY
6.REPLACE REAR TELEVISION CAMERA ASSEMBLY
a.

Replace the rear television camera assembly with a new or normally functioning one (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>TELEVISION CAMERA>REMOVAL).



NEXT

7.CHECK FOR DTC
7.CHECK FOR DTC

b.

Check for DTCs (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>REAR VIEW MONITOR SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
No DTC is output A
DTC is output (w/o Navigation System) B
DTC is output (w/ Navigation System) C



A

END (REAR TELEVISION CAMERA ASSEMBLY WAS DEFECTIVE)

B

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

C