The display signal of the rear television camera assembly is transmitted to the radio and display receiver assembly*1 or navigation receiver assembly*2.
*1: w/o Navigation System
*2: w/ Navigation System
Disconnect the F128 radio and display receiver assembly connector*1 or F133 navigation receiver assembly connector*2.
Disconnect the P15 rear television camera assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F128-11 (CA+) - P15-6 (CB+)*1 | Always | Below 1 Ω |
| F128-12 (V+) - P15-3 (CV+)*1 | Always | Below 1 Ω |
| F128-24 (V-) - P15-2 (CV-)*1 | Always | Below 1 Ω |
| F128-23 (CGND) - P15-5 (CGND)*1 | Always | Below 1 Ω |
| F128-11 (CA+) - Body ground*1 | Always | 10 kΩ or higher |
| F128-12 (V+) - Body ground*1 | Always | 10 kΩ or higher |
| F128-24 (V-) - Body ground*1 | Always | 10 kΩ or higher |
| F128-23 (CGND) - Body ground*1 | Always | 10 kΩ or higher |
| F133-11 (CA+) - P15-6 (CB+)*2 | Always | Below 1 Ω |
| F133-12 (V+) - P15-3 (CV+)*2 | Always | Below 1 Ω |
| F133-24 (V-) - P15-2 (CV-)*2 | Always | Below 1 Ω |
| F133-23 (CGND) - P15-5 (CGND)*2 | Always | Below 1 Ω |
| F133-11 (CA+) - Body ground*2 | Always | 10 kΩ or higher |
| F133-12 (V+) - Body ground*2 | Always | 10 kΩ or higher |
| F133-24 (V-) - Body ground*2 | Always | 10 kΩ or higher |
| F133-23 (CGND) - Body ground*2 | Always | 10 kΩ or higher |
Reconnect the radio and display receiver assembly connector*1 or navigation receiver assembly connector*2.
Reconnect the rear television camera assembly connector.
*1: w/o Navigation System
*2: w/ Navigation System
OK
NG
Disconnect the radio and display receiver assembly connector*1 or navigation receiver assembly connector*2.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F128-24 (V-) - Body ground*1 | Always | 10 kΩ or higher |
| F128-23 (CGND) - Body ground*1 | Always | 10 kΩ or higher |
| F133-24 (V-) - Body ground*2 | Always | 10 kΩ or higher |
| F133-23 (CGND) - Body ground*2 | Always | 10 kΩ or higher |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| F128-11 (CA+) - F128-23 (CGND)*1 | Ignition switch ON, shift lever in R | 5.5 to 7.05 V |
| F133-11 (CA+) - F128-23 (CGND)*2 | Ignition switch ON, shift lever in R | 5.5 to 7.05 V |
| *A | w/o Navigation System |
| *B | w/ Navigation System |
| *a | Component with harness connected
(Radio and Display Receiver Assembly*1 or Navigation Receiver Assembly*2) |
*1: w/o Navigation System
*2: w/ Navigation System
| Result | Proceed to |
|---|---|
| OK | A |
| NG (w/o Navigation System) | B |
| NG (w/ Navigation System) | C |
A
B
C
Reconnect the rear television camera assembly connector.
Check the waveform of the rear television camera assembly using an oscilloscope.
| *A | w/o Navigation System |
| *B | w/ Navigation System |
| *a | Component with harness connected
(Radio and Display Receiver Assembly*1 or Navigation Receiver Assembly*2) |
A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the radio and display receiver assembly*1 or navigation receiver assembly*2 with the connector connected.
| Item | Content |
|---|---|
| Terminal No. (Symbol) | F128-12 (V+) - F128-24 (V-)*1
F133-12 (V+) - F133-24 (V-)*2 |
| Tool Setting | 200 mV/DIV., 50 μsec./DIV. |
| Condition | Waveform 1: Ignition switch ON, shift lever in R
Waveform 2: Ignition switch ON, shift lever in R, screen blacked out by covering camera lens |
Waveform is as shown in the illustration.
The video waveform changes according to the image sent by the rear television camera assembly.
| *a | Waveform 1 |
| *b | Waveform 2 |
| *c | Synchronized Signal |
| *d | Video Waveform |
*1: w/o Navigation System
*2: w/ Navigation System
OK
(See pageAudio / Visual / Telematics>PARK ASSIST / MONITORING>REAR VIEW MONITOR SYSTEM>PROBLEM SYMPTOMS TABLE)
NG